Every now and again we get a pair of late 912 rear calipers in-house. These rare calipers share the 38mm piston diameter with the 914-6 and all 911's (for practical purposes) through 1983. These also have the same #31 pad size associated with the 914-6 and 911 calipers. So... larger pistons and larger pad size.
What are these good for? If you've moved to 5-lug up front and you're now using anything from an M-Caliper (stock 914-6), an S-Caliper (911S, RS, 930), an A-Caliper (911SC through 1983) or a Wide A-Caliper (911 Carrera) these would be a bolt on caliper that would retain the braking bias those cars were set up with (48mm pistons up front and 38mm pistons in the rear).
These are true late 912 calipers vs. 911 rear M-Calipers. What's the difference? They don't have the 10mm spacers. They have the same Ribe R6 cap head fasteners just in the shorter length to accomodate the spacerless application. Because there's no spacers, these fit over a solid 914 or 914-6 rotor (keeps weight down). With the 3" mounting ear spacing, these bolt right on to a 914 rear control arm.
***There is no handbrake option if you install these. This is why they are recommended as race calipers only*** You can add a spot caliper or, install the early 911 handbrake assembly to your arms but, these are really a great solution for the track car that needs proper rear bias and a larger pad without worrying about the DMV and their rules and regulations. You'll probably want a 19mm MC as well.
Comes with everything you need (pins springs and bleeders) with the exception of pads (we can help there too...)
Our normal restoration price is $249.00 plus cores. These will sell fo $199.00 for the pair with no core required. Shipping is $9.85 Flat Rate to anywhere in the US. Ask for International shipping. Crappy picture below:
So are these better than using front 914 calipers on the rear?
I was thinking the same thing! Just cuz that's what I currently have...
Eric,
Thanks for the reply and I see your point about proper bias being crucial. However, isn't the front/rear bias dependent on what calipers are used up front?
I currently have "A" calipers up front and 914-4 fronts in the rear, and the bias is just about right from what I can tell. I do actually want to adjust it a teeny bit more toward the front though, so I am about to install an adjustable prop valve.
My car is nowhere near stock and I am using full race pads (Pagid), very stiff suspension, Hoosiers, etc. so my setup should not be construed as good for the street or for other cars/drivers...
Eric,
You have a PM.
You can also bias brakes with pad compound. ie: stickier pads up front and not so sticky in the rear... .
..........Question for ERIC SHEA.....With any or all of the calaper combinations you discussed....do any of the combinations ALLOW the removal of the stock... brake bias/brake pressure requlator?...or do to a specific combination,is the B.B. P.requlator... removed to achieve maximum breaking ability?...M.M.
Eric, are the 4 and 6 pressure regulators the same then?
Nope, they have different values but I think it is very small. I think(someone will have to check) the -4 has 17 stamped on the housing and the -6 has 19 stamped on it. I do not know if this refers to the diameter of the opening like the 17mm and 19mm master cylinder have. Things that make you go hummmm! I will get out the shop manuals and see what they say on the spec's.
I find that when I autocross and when I am on the track I am either on the gas or fill tilt boogie on the brakes. One thing I know for sure is I don't want the pressure regulator "shutting down" ANY of the brakes at ANY time under these driving conditions. No matter how well the thing is engineered, there are proper parts for each application and one should know what they are doing when messing with any of them. I, for instance, don't believe the stock pressure regulator is good for a race application. I don't need to know ALL the rates of grip for pads to know the difference of what works for me and what doesn't. If you don't do your own setup and know what is working for you and what doesn't, you need to have someone else tell you what to do. If you build, tune and test your own equipment then you can do the math yourself instead of relying on someone elses opinion of what is going to work for you.That's why I didn't list which compounds would work for any given situation. Because I don't know. You need to do some work to make that happen.
I do know that Dan is not the first one, nor is he the only one to do this succesfully. Many folks that race their cars tune brake bias with pads. Need proof... go to a GGR AX event and I'll show you.
That said, if you do not do your own work or can not test and tune your own equipment then one of the few folks I would trust with my brakes is Eric. No one person can know everything and race applications are very car/driver specific so that throws a monkey wrench into the whole game.
I actually subscribed to the school (5+ years ago) that it made sense to remove the regulator thingie and use a tee. I have found empirically through numerous track events that I can in fact get the balance "very close" with my particular setup and pads. I am actually using two different compounds front and rear, as Mike alludes to. That said, the car is not as stable as I want under extreme straight-line braking, even with an LSD and so I am going to try an adjustable prop valve and see what the result is.
Just an idea - there is some interesting stuff in this thread and maybe we can get an admin to copy/move it over to the Garage or Paddock since we aren't normally supposed to discuss tech details in the classifieds!
I was using differing pad compounds back in the early 90s and I was not the first by a long shot. My 2.7RS motors 6 had identical JFZ 4 pot calipers front and rear...I ran Pagid orange up front and cut down, stockish pads in the rear....worked great.
Is this for everyone, no way. Takes time patience and a well calibrated butt.
Listen to Eric's wise advice for a street car, he is right on the money.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)