Printable Version of Topic
Click here to view this topic in its original format
914World.com _ FS/WTB: 914 Parts _ FS: This Nor East 75 followed me home
Posted by: okieflyr Nov 21 2010, 08:07 PM
A friend of a friend had this abandonded car that supposedly "ran well" a few years ago.
So on the way back from MUSR, Leesa and I stopped to check it out. It was I figured, rusty and sitting outside for a few years. It did have a nice easter egg though, a CRACK FREE DASH! and Euro lenses on all corners. The hell hole is a two fisted perforation on two planes, but the doors still open and close like a dream.
I hate to cut it up, but it is very rusty and and there is no title. I'm going to part it out for certain pieces that I want to keep, and I'm considering keeping the rear half for a trailer. 
I pulled the plugs and they looked good. Oiled the top of the cylinders, and will do a makeshift fuel sytem to get it running before I pull it apart.
Unless someone is looking for a project????
Posted by: ws91420 Nov 21 2010, 08:11 PM
Hey Kev if you dont want them can I have the speaker pods?
Posted by: mepstein Nov 21 2010, 08:11 PM
I'm looking for a windshield if this one looks good. Will pick up. Let me know. Thanks, Mark
- also the center console and driver side rear view mirror if the price is right. Might have some stuff you want for trade. 
Posted by: okieflyr Nov 21 2010, 08:13 PM
A few more pic's..
Posted by: RJMII Nov 21 2010, 08:14 PM
OUCH, Kevin! That's a HUGE whole in the hell hole area. The d-side quarter seems to be a different shade of silver than the door and front fender... was it in a fender bender, too? (and been repaired from it) or is it just the shadowing?
Posted by: okieflyr Nov 21 2010, 08:20 PM
OUCH, Kevin! That's a HUGE whole in the hell hole area. The d-side quarter seems to be a different shade of silver than the door and front fender... was it in a fender bender, too? (and been repaired from it) or is it just the shadowing?
Yes it had been in a drivers side fender bender, and the front fender is a fiberglass replacement. Every corner on every panel is rusted, but it does have a small collection of factory "options".
Posted by: okieflyr Nov 21 2010, 08:26 PM
Hey Kev if you dont want them can I have the speaker pods?
I'll try and save them for you, they are of some custom plywood configuration, so I'm not sure how to get them apart yet.
Posted by: okieflyr Nov 21 2010, 08:33 PM
I'm looking for a windshield if this one looks good. Will pick up. Let me know. Thanks, Mark
- also the center console and driver side rear view mirror if the price is right. Might have some stuff you want for trade.
Mark, the drivers rear view is bent toast, I'll get the glass clean to see what kind of shape it's in (It's original) and it's almost loose enough to fall out. I'll keep you posted.
I'll start a parts thread in the classifieds when I get closer to stripping..
Posted by: mepstein Nov 21 2010, 08:42 PM
I'm looking for a windshield if this one looks good. Will pick up. Let me know. Thanks, Mark
- also the center console and driver side rear view mirror if the price is right. Might have some stuff you want for trade.
Mark, the drivers rear view is bent toast, I'll get the glass clean to see what kind of shape it's in (It's original) and it's almost loose enough to fall out. I'll keep you posted.
I'll start a parts thread in the classifieds when I get closer to stripping..
Loose is gud. Less likely to crack when removed. If that dash doesn't survive the removal process, I have a late model dash, in great condition, available for trade. Thanks, Mark
Posted by: type11969 Nov 21 2010, 08:50 PM
Are either of the rear fenders in decent enough shape to save? If so I am interested. Let me know.
-Chris
Posted by: abayer1969 Nov 22 2010, 03:55 AM
Hey Kevin whats up with the steering wheel? 
Posted by: stephenaki Nov 22 2010, 05:17 AM
The heater control unit looks in a lot better shape than mine, i'd be interested.
Posted by: 914runnow Nov 22 2010, 07:10 AM
Back Pad behind seats???
Available and condition???
Thanx Rx in Colorado
Posted by: plas76targa Nov 22 2010, 07:55 AM
Kevin,
You want the motor? I might be interested in the motor, empi wheels, and a dash switch or two (fog lights, emergency flash).
Matt
Posted by: TROJANMAN Nov 22 2010, 07:58 AM
Back Pad behind seats???
Available and condition???
Thanx Rx in Colorado
Rex,
I think I have a perfect backpad in my attic if you want it.
Posted by: garyb Nov 22 2010, 08:39 AM
I need the carpet for behind the seats if it's in good shape.
Thanks
Gary
Posted by: zonedoubt Nov 22 2010, 01:09 PM
I'll take the fuel pump cover and bracket if it's in good shape. PM sent.
Posted by: indianmort Nov 22 2010, 01:18 PM
that one is mint compared to mine. if you part would you have the front heater tube that is in the long on the passenger side. thanks.
Posted by: moparrob Nov 22 2010, 09:26 PM
I need to make an access cover for my _6 conversion, so I'm looking for the center section of the firewall to cut a section larger than the one I'm going to cut out.
if it is still intact and you're willing to ship it let me know.
Thanks.
Rob
robrose426@att.net
Posted by: okieflyr Nov 23 2010, 11:23 AM
I need to make an access cover for my _6 conversion, so I'm looking for the center section of the firewall to cut a section larger than the one I'm going to cut out.
if it is still intact and you're willing to ship it let me know.
Thanks.
Rob
robrose426@att.net
Rob, this should not be a problem. I'll get with you before I get to the sawsall for your desired dimensions.
Posted by: zy84 Nov 23 2010, 11:39 AM
How bad is the cowl section? I need a cowl section to replace my rusty one.
Posted by: BarberDave Nov 23 2010, 04:27 PM
Center Console looks good . I could use it for my chairty builds. How much shipped to 43567. Go easy on me. Let me know. Dave 
and the heater lever!
Posted by: dashgod Nov 24 2010, 12:56 PM
I'm looking for both a foglight switch and a headlight switch.
Thanks,
Dave
Posted by: draganc Nov 26 2010, 10:07 PM
hi,
i sent you a pm a few days and would take the rear sway bar incl. bolts. i could swing by next week - i'm in central nj.
Posted by: okieflyr Nov 27 2010, 12:58 PM
How bad is the cowl section? I need a cowl section to replace my rusty one.
From the topside it looks to be ok. are you looking for the piece to be cut just beyond fender to fender? I'm not cutting yet, but I look to start in the next week or two.
Kevin
Posted by: okieflyr Nov 27 2010, 01:03 PM
I'm looking for both a foglight switch and a headlight switch.
Thanks,
Dave
I'm going to hang on to them since I'll soon need replacements as well, sorry...
Posted by: okieflyr Nov 27 2010, 01:09 PM
I'll take the fuel pump cover and bracket if it's in good shape. PM sent.
I'll try and get you a picture today.
Posted by: type11969 Nov 27 2010, 04:47 PM
Kevin-
How about those rear fenders? Useable? I can come down to help you cut it up. Have sawzall, will travel. Let me know.
-Chris
Posted by: okieflyr Nov 27 2010, 05:35 PM
Kevin-
How about those rear fenders? Useable? I can come down to help you cut it up. Have sawzall, will travel. Let me know.
-Chris
Chris,
I got a few pics today for ya, I'll get them up this eve to give you an idea.
Posted by: okieflyr Nov 27 2010, 07:30 PM
Kevin-
How about those rear fenders? Useable? I can come down to help you cut it up. Have sawzall, will travel. Let me know.
-Chris
Here you go Chris, Driver's side, your call.
Posted by: okieflyr Nov 27 2010, 07:37 PM
Here is the passenger side.
Posted by: hashagen7 Nov 28 2010, 07:13 AM
How much for the front bumper, pad, and grilles? I can pick up.
Posted by: okieflyr Nov 28 2010, 07:45 AM
How much for the front bumper, pad, and grilles? I can pick up.
I'll do $25.00 for the bumper, pad, and mounted lights. It needs some cleaning but is otherwise in good shape. Are you talking about the eng compartment grills?
Posted by: okieflyr Nov 28 2010, 01:51 PM
I got the 1.8 engine running this weekend(history unknown) and it sounds fine and not smoking. I will be looking to sell it locally as I have no time to ship it. Iexpect to pull it out in the next week or so if anyone wants to listen and check it out beforehand. I will be including the motor, all fuel injection, good heat exchangers, and muffler system for $450.00
The side shift trans will also be available for $200. The system could be plug and play....
Posted by: type11969 Nov 28 2010, 06:29 PM
Kevin-
Thanks for the pics. Those fenders look pretty rough, I'll have to dig in my basement to find the spares I have, but I think they are in better shape than those. I'm sure those are fried under that vinyl too.
-Chris
Posted by: okieflyr Nov 29 2010, 07:28 PM
Kevin-
Thanks for the pics. Those fenders look pretty rough, I'll have to dig in my basement to find the spares I have, but I think they are in better shape than those. I'm sure those are fried under that vinyl too.
-Chris
Your welcome to any "patch" metal if you need some.
Posted by: Cairo94507 Dec 2 2010, 08:06 PM
Hello:
Looking for complete original front & rear sway bars. If the rear is still available I would be interested if it comes with all of the parts, including the reinforced trunk part. Also if the car has a stock 15mm front bar I would be equally interested.
Thanks,
Michael
Posted by: okieflyr Dec 2 2010, 10:40 PM
Hello:
Looking for complete original front & rear sway bars. If the rear is still available I would be interested if it comes with all of the parts, including the reinforced trunk part. Also if the car has a stock 15mm front bar I would be equally interested.
Thanks,
Michael
Michael,
I no longer have the rear bar, but I do have the factory front 15mm bar that is complete if that still helps. I was looking to get $150 +shipping. I could ship it out on Monday.
Posted by: sfrenck Dec 3 2010, 11:32 AM
Looking for the rear trunk lid and the right side door (maybe both doors) if they're straight and in good condition.
Thanks,
Scott
Posted by: okieflyr Dec 4 2010, 08:49 AM
Looking for the rear trunk lid and the right side door (maybe both doors) if they're straight and in good condition.
Thanks,
Scott
The rear trunk lid is very rusty as are the doors. I'm going to keep and use the drivers door, and decklid for parts, but your welcome to take a look at the pass door. It is straight and opens and closes very easy and smooth, but it like most of this car it is rusty with a perforation on the front lower edge.
I'm right off of Naamans Rd on the PA side. You can reach me at six one zero
five seven four five two zero eight if you want to look at this soon to be carcass.
Posted by: sfrenck Dec 4 2010, 10:13 AM
Looking for the rear trunk lid and the right side door (maybe both doors) if they're straight and in good condition.
Thanks,
Scott
The rear trunk lid is very rusty as are the doors. I'm going to keep and use the drivers door, and decklid for parts, but your welcome to take a look at the pass door. It is straight and opens and closes very easy and smooth, but it like most of this car it is rusty with a perforation on the front lower edge.
I'm right off of Naamans Rd on the PA side. You can reach me at six one zero
five seven four five two zero eight if you want to look at this soon to be carcass.
Thanks anyway - doesn't sound like your passenger door is any better than the one I have.
I think I've seen you in your 914 last summer - I live in Northminster off of Foulk Rd (right across from Safeway). There's actually another 914 up the street from me as well (Olympic blue). Funny how many of these cars are around when you start looking for them.
Posted by: okieflyr Dec 4 2010, 08:29 PM
I think I've seen you in your 914 last summer - I live in Northminster off of Foulk Rd (right across from Safeway). There's actually another 914 up the street from me as well (Olympic blue). Funny how many of these cars are around when you start looking for them.
[/quote]
Well since we are neighbors we should meet up. Do you know the other owner?
I've not seen any others on the road in this area but it would be nice.
Posted by: mepstein Dec 4 2010, 09:18 PM
[quote name='okieflyr' date='Dec 4 2010, 09:29 PM' post='1402073']
I think I've seen you in your 914 last summer - I live in Northminster off of Foulk Rd (right across from Safeway). There's actually another 914 up the street from me as well (Olympic blue). Funny how many of these cars are around when you start looking for them.
[/quote]
Well since we are neighbors we should meet up. Do you know the other owner?
I've not seen any others on the road in this area but it would be nice.
[/quote]
* We could always meet at my house. I need some help with an engine drop. I've never done it before and don't have jacks. Lunch/beer/whatever on me. I'm in Landenberg off 41. Only ~ 20 minutes from you guys.
Posted by: sfrenck Dec 5 2010, 07:51 AM
Time is pretty tight around the Holidays - but I'm game to helping with the engine drop. I'm sure Bryan (brenz) would help also (Kevin - Bryan works with me, has a 914, and lives down by Bellvue State Park)
The guy up the street doesn't seem to be into his 914 that much - got a "it's my wife's car" response when talking to him about it at Little League practice this past summer.
Posted by: mepstein Dec 5 2010, 04:20 PM
Time is pretty tight around the Holidays - but I'm game to helping with the engine drop. I'm sure Bryan (brenz) would help also (Kevin - Bryan works with me, has a 914, and lives down by Bellvue State Park)
The guy up the street doesn't seem to be into his 914 that much - got a "it's my wife's car" response when talking to him about it at Little League practice this past summer.
No problem waiting until after Christmas/New Year.
Posted by: okieflyr Dec 5 2010, 04:56 PM
Time is pretty tight around the Holidays - but I'm game to helping with the engine drop. I'm sure Bryan (brenz) would help also (Kevin - Bryan works with me, has a 914, and lives down by Bellvue State Park)
The guy up the street doesn't seem to be into his 914 that much - got a "it's my wife's car" response when talking to him about it at Little League practice this past summer.
No problem waiting until after Christmas/New Year.
Posted by: type11969 Dec 5 2010, 05:17 PM
Sounds like a good time, I'd be willing to make the drive, keep me in the loop.
-Chris
Posted by: plas76targa Dec 8 2010, 01:05 PM
Ditto. i'll drive up from MD. say when
Posted by: okieflyr Dec 8 2010, 09:36 PM
This could be a nice meet- n- greet to start the new year! I have to travel between Jan 4-11th, but i'm available before and after.
On the part-out front, I've now got the motor and transmission out and available for sale. This weekend sould give me some more garage time to begin the dismantled parts requests.
Posted by: mepstein Dec 9 2010, 10:16 AM
I will start a thread in the garage for the engine drop/meet-n-greet so Kevin can have his thread back. Mark
Posted by: MassTeener Dec 25 2010, 05:24 PM
Looking for side-shift conversion parts minus the trans...
Thanks
Posted by: okieflyr Dec 25 2010, 06:29 PM
I can set you up with the shift rods, and a late engine bar, but I'm going to keep the trans whole for now.
Posted by: chadhuskey Dec 26 2010, 08:11 AM
how much for the whole dash? (top pad face etc)?
thanks
-chad
Posted by: chadhuskey Dec 26 2010, 08:12 AM
and maybe a price on the targa top?
and drivers side door armrest
hahaha
-chad
Posted by: okieflyr Dec 27 2010, 07:00 PM
Chad,
I'm going to keep the dash top since it is crack free. The rest of the dash is available and dissasembled if needed. The driver's door pocket is in decent shape $30.00 shipped.
The Targa top $65.00 + shipping.
Posted by: grouperalley Jan 1 2011, 12:33 AM
what kind of shape is the front valance. i'd be intrested if shipping to 32789 doesn't kill me. thanks Brad
Posted by: okieflyr Jan 1 2011, 07:34 PM
what kind of shape is the front valance. i'd be intrested if shipping to 32789 doesn't kill me. thanks Brad
Brad,
The valance on this car is beat up. I do have another that on a scale of 1-10 rates 8-8.5. All the attatchment points are good and it is very straight. The loss of points are due to the fact there are very subtle soft indentions around both torsion bar crowns that are hard to see, and it will need to be painted. $30.00
The shipping is probably $15-20, but I'd need to make sure I can get a long enough box to pack it well. I can getyou some pics, but it will be mid week before I can get them sent. PM me and adress to send them if it is of interest.
Posted by: gsbeane Jan 9 2011, 08:46 PM
how much for the steering wheel with shipping to 45014?
Posted by: okieflyr Jan 13 2011, 08:15 PM
how much for the steering wheel with shipping to 45014?
I'm keeping the wheel for now...
Posted by: matteyp Jan 22 2011, 08:06 PM
Looking for switches, PM sent
Posted by: rwfms Jan 23 2011, 05:23 PM
Don't know what the market is for salvage wiring harnesses but I need a couple of individual female pin connectors with a length of wire from a 12 or 14 pin plug terminal to the relay board. I have a couple of terminal wires broken off at the pin and would like to splice in some good connector/wires from a partial or otherwise unuseable harness. My harness already has some modifications for a 6 conversion.
Thanks,
Ron
Posted by: de474 Jan 23 2011, 06:08 PM
Anything left over?
Posted by: okieflyr Jan 23 2011, 07:36 PM
Don't know what the market is for salvage wiring harnesses but I need a couple of individual female pin connectors with a length of wire from a 12 or 14 pin plug terminal to the relay board. I have a couple of terminal wires broken off at the pin and would like to splice in some good connector/wires from a partial or otherwise unuseable harness. My harness already has some modifications for a 6 conversion.
Thanks,
Ron
Ron,
I saved the complete harness from the car, but I need to separate a couple of circuits from it. PM me for your specific needs.
Kevin
Posted by: okieflyr Jan 23 2011, 08:19 PM
Anything left over?
Off the top of my head.....
Running 1.8 with all injection $300.00*****SOLD
Side shift trans w/excellant console boot $200*****SOLD
Fuel tank $25.00
Fuel pump $65.00
Axles/CV's $45.00 pr
Gauge cluster $65.00
Front swaybar $75.00*****SOLD
Crack free rain tray $50.00
Tail lights (avg cond) 35.00pr*****SOLD
Shiftrods for sideshift trans $25.00*****SOLD
Backpad $40.00
Late Targa Top $45.00 Local pickup only
SOLD ****** Nice Center Console with two working gauges $175.00 + shipping SOLD
****** Rear Factory Defroster glass/Harness/Relay tray/switch $150.00+shipping
All offers considered, and shipping is available for lighter/smaller items.
Posted by: dkos Jan 24 2011, 03:44 PM
did you sell the windshield?
Posted by: okieflyr Jan 24 2011, 07:35 PM
did you sell the windshield?
It has some scratches so I'm not really pushing it. May keep it as a spare though, lot,s o'crap flying on these roads.
Posted by: dkos Jan 25 2011, 08:09 AM
did you sell the windshield?
It has some scratches so I'm not really pushing it. May keep it as a spare though, lot,s o'crap flying on these roads.
lots o'crap flying in my garage too. I dropped a 2x4, off the rafters, thru my windshield. If you decide to sell it let me know.
Posted by: okieflyr Jan 25 2011, 11:24 AM
did you sell the windshield?
It has some scratches so I'm not really pushing it. May keep it as a spare though, lot,s o'crap flying on these roads.
lots o'crap flying in my garage too. I dropped a 2x4, off the rafters, thru my windshield. If you decide to sell it let me know.
OUCH!
In that case your welcome to come take a look. If you have a daily driver it may be ok.
It is not nice enough for a restored ride due to some blade scratches though.
Posted by: tjmonk Feb 4 2011, 05:14 PM
I am new to this and tried to read all of the post, but still need to know if the following are available:
Rear sway bar set up
euro lens
Thanks
A friend of a friend had this abandonded car that supposedly "ran well" a few years ago.
So on the way back from MUSR, Leesa and I stopped to check it out. It was I figured, rusty and sitting outside for a few years. It did have a nice easter egg though, a CRACK FREE DASH! and Euro lenses on all corners. The hell hole is a two fisted perforation on two planes, but the doors still open and close like a dream.
I hate to cut it up, but it is very rusty and and there is no title. I'm going to part it out for certain pieces that I want to keep, and I'm considering keeping the rear half for a trailer.
I pulled the plugs and they looked good. Oiled the top of the cylinders, and will do a makeshift fuel sytem to get it running before I pull it apart.Unless someone is looking for a project????
Posted by: okieflyr Feb 5 2011, 07:20 PM
[quote name='tjmonk' date='Feb 4 2011, 06:14 PM' post='1427125']
I am new to this and tried to read all of the post, but still need to know if the following are available:
Rear sway bar set up
euro lens
Thanks
The rear swaybar has been sold, and I've moved the lenses to my car to keep.
But there is still quite abit left!
Kevin
Posted by: okieflyr Feb 5 2011, 07:51 PM
******SOLD********
Center console with working gauges, and offset heater handle, but dead clock.
There are two very small punctures on the passenger side kick panel. NO CIGARETTE BURNS!
Posted by: okieflyr Feb 5 2011, 07:55 PM
Rear defroster glass/harness/relay board/ switch
Posted by: BarberDave Feb 6 2011, 05:48 AM
P.M. Sent on the console . Barberdave
Posted by: okieflyr Mar 1 2011, 08:46 PM
Bumping this thread back to life.
I'd rather sell it here than haul it to Hershey!
Pics to come: 1980's Gold Mesh BBS (2)15x7 (2) 15x8's $300.00 for the set
1970? Pair 110mm stub axles $75.00 shipped contus
Posted by: chuckc Mar 2 2011, 07:03 AM
Hey hey,
my low beams don't work, I think it's the headlight power relay...the square one with a kind of clip on top of it to hold it in place on the fuse panel? My dad lives in Kennett Square, I'm garaging at his place starting in April. If you have it and it works maybe I could get it from you then and see if it works? How much do you want?
peace,
Chuck
Posted by: edrotol Mar 2 2011, 08:42 AM
Bumping this thread back to life.
I'd rather sell it here than haul it to Hershey!
Pics to come: 1980's Gold Mesh BBS (2)15x7 (2) 15x8's $300.00 for the set
1970? Pair 110mm stub axles $75.00 shipped contus
Pm sent for defroster rear window, etc.
Posted by: okieflyr Mar 2 2011, 08:44 PM
Hey hey,
my low beams don't work, I think it's the headlight power relay...the square one with a kind of clip on top of it to hold it in place on the fuse panel? My dad lives in Kennett Square, I'm garaging at his place starting in April. If you have it and it works maybe I could get it from you then and see if it works? How much do you want?
peace,
Chuck
The relay is already gone. Check your grounds real well if you haven't already.
Give a heads up when you come down this way and maybe we could meet up!
Kennett is a beautiful area and drive.
Posted by: ppetion Mar 2 2011, 10:42 PM
Hey hey,
my low beams don't work, I think it's the headlight power relay...the square one with a kind of clip on top of it to hold it in place on the fuse panel? My dad lives in Kennett Square, I'm garaging at his place starting in April. If you have it and it works maybe I could get it from you then and see if it works? How much do you want?
peace,
Chuck
The relay is already gone. Check your grounds real well if you haven't already.
Give a heads up when you come down this way and maybe we could meet up!
Kennett is a beautiful area and drive.
pm sent for engine and possible tranny
Posted by: Griffinroydonald Mar 13 2011, 08:46 PM
Looking for late model front bumper parts -Anything left ?
Posted by: okieflyr Mar 14 2011, 05:57 AM
Looking for late model front bumper parts -Anything left ?
I do have the front and rear bumpers in decent shape, but given the shipping weight you may be better off looking closer to home.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)