Got my latest set of parts back from the platers and here is some of what I have to offer my fellow teeners. All parts are plus shipping, most will fit into an envelope for $5 and ALOT will fit into a flat rate box for $10.
Upper Front Trunk Latches, $30
http://img832.imageshack.us/i/dscf0057i.jpg/
http://img854.imageshack.us/i/dscf0058i.jpg/
Lower Front Trunk latches, $25
only one early <'72 latch (one spring)
http://img508.imageshack.us/i/dscf0050jh.jpg/
http://img607.imageshack.us/i/dscf0051z.jpg/
http://img19.imageshack.us/i/dscf0052t.jpg/
http://img41.imageshack.us/i/dscf0053xz.jpg/
Engine lid latch $17, $20 with replated backing plate.
http://img190.imageshack.us/i/dscf0059g.jpg/
Front trunk spare tire hold down screw and plate. $15
http://img823.imageshack.us/i/dscf0055s.jpg/
http://img219.imageshack.us/i/dscf0056v.jpg/
Rear trunk upper latch with unbreakable metal plungers $30
http://img846.imageshack.us/i/dscf0061e.jpg/
Transmission mount hardware. $35 per set
http://img847.imageshack.us/i/dscf0062ss.jpg/
Pedal board rubber stop holder. $10
http://img62.imageshack.us/i/dscf0065ax.jpg/
Transmission pulley mount. $25
http://img19.imageshack.us/i/dscf0066jy.jpg/
http://img684.imageshack.us/i/dscf0071df.jpg/
Ebrake handle cable. $40, $50 w/ equalizer and pin
http://img19.imageshack.us/i/dscf0081h.jpg/
gas tank mounted charcoal canister bracket. $15
http://img97.imageshack.us/i/dscf0070o.jpg/
Rear axle castle nut w/ washer. $20 per set.
http://img34.imageshack.us/i/dscf0072v.jpg/
Trailing arm bearing covers. $15/pr
http://img52.imageshack.us/i/dscf0073h.jpg/
Trailing arm pivot arm nuts. $12/pr
http://img833.imageshack.us/i/dscf0074oo.jpg/
Brake line clips 4/$10
http://img855.imageshack.us/i/dscf0075k.jpg/
Front suspension taper pins. $10 each
http://img811.imageshack.us/i/dscf0076u.jpg/
Balljoint star washers. $10/pr
http://img696.imageshack.us/i/dscf0077g.jpg/
Balljoint retainer nuts $25/pr
http://img816.imageshack.us/i/dscf0078c.jpg/
Front Strut top plates. $13/pr
http://img820.imageshack.us/i/dscf0079t.jpg/
And one pair of BMW drop links made to fit 914 rear sway bars. Selling these for the cost of machining them. $75
http://img219.imageshack.us/i/dscf0080e.jpg/
Beautiful work Bruce ! Will you be selling at the G & R Rusty Parts swapmeet Sunday May 1st ?
Smoking deals!!!!!
Bruce,
Are you bringing the parts to the Sunday bash? I want some of what I see.
I need to go over some things with you to arrange getting over after the bash to finalize what I need.
I am finally home for 2 months after 4 months on the road.
See you Sunday!
Thanks!
John
PM sent
PM SENT
Yes I will be at the G and R swap meet with all my shiny plated parts. All PMs replied. Also, if there are any parts you would like or need plated just ask, I have almost everything off these cars replated and in a box somewhere. o ya, BUMP!
I too have bought many parts from Bruce, clearly top quality at very fair prices !
Hey Bruce, I'll take a upper front truck latch, a lower front truck latch for a 73, a spare tire hold drown, and a rear truck upper latch, total please with S/H to 94531 and paypal address. Thanks John
Very nice...any door strikers?
Bruce,
I'll take a pair of the front strut top braces. Have any matching nuts?
Pat
Bruce,
Please put me down for the following: Upper Front Trunk latch, Lower Front Trunk Latch, Rear Trunk Upper Latch and a pair of Front Strut Top Plates. I'm going to try to make it to the G&R Swap meet on Sunday. If I don't see you there, let me know what you need from me to mail the parts.
Thanks,
Eric
for ya.
I would like the front top hood latch, one spare tire hold down screw & plate, Transmission mount set (side shift), set of brake line clips, and pair of ball joint star washers. PM me if you still have all these and I'll send paypal for order.
and I agree, Bruce has fair prices and excellent service!
Bruce called last Saturday, said my order has been sent. And I got
them Monday in all their plated and powdered glory. And his many tips
and suggestions on my vacuum line mis-match was easily fixed with tip
#4 (put the small hose into the big hose trick). Some rubber cement to
seal the hoses together and that was it. Buy parts from Bruce and
you will not be disappointed. I was not.
Bruce by chance did you have any of those heater cap straps for the engine tin replated?
Bruce much appreciated. Still need a nice cap & strap.
PM sent
Bruce
Got any front lower Hood latches and rear trunk latches left? Also may need the latch that mounts to the hood up front. For a 74 914.
Thanks
Phillip
I should have those still available. I will check later and get back to you.
Brruce I love you shiny parts and you never come by with them like you the 914 ice cream man anyumore..
seriously the expensive ball pin joints are not supposed to be re-use, I am not trying to be Knowledgeable just looking out for your protection and you customer. They are $20 each at Pelican but loose control of one wheel and your dead screwed, happend to me on a differnet part that one pin/bolt came out as I pulled from a stop at the end of a fwy off ramp 3;30 in the morngin... If i was doing 75 when it happend .. justy a heads up.,,
Joe,
Thanks for the heads up about the taper pins.
I wonder if the problem with the pin coming out was with the special retaining nut with the slit on the side?
I have a shop now where you and other 914 nuts ( not that you are one ) are welcome to come and salivate over Porsche parts. Free cup of chilled Sparklets water with any purchase.
The shop is at:
10000 Indiana Ave
Suite #9 Riverside CA
Call before coming as I am not at the shop that much but it is only 2 miles from the house.
Bruce
Bruce, If you still have the trailing arm nuts and the trailing arm bearing caps I'll take them and also a set of transmission hardware. paypal address John
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)