I have come to the conclusion that I will not be able to finish this project so therefore I will be selling everything piece by piece. I basically have every part to make a car plus many brand new upgraded parts from PMB, Patrick Motorsports, Pelican, AA, steel flares, F/G lids, bumpers, valances, for a GT from QRS, etc ..
I plan on inventorying everything I've got. My loss.
If you guys want to stop by and see what I got just shoot me a message or call me at 949-887-1274.
Thanks.
Ed
PS. Stand by for more inventory pics. You can let me know what you want to see too.
Is that an original black car?
Well crud, sorry to hear that, Ed. I came by your place a couple years back. IIRC, I bought a trunk or hood. Anyway I was looking forward to your build .
Ed,
which brand and how are the fiberglass front and rear lids made?
I've been wanting a pair...
I like that they are ribbed
but I don't have hinges for bolt on anylonger
brant
Is your rear lid with or without the spoiler? Is the front lid with or without headlight cutouts? Thanx
Bummer! wish I still lived in Huntington Beach.
How much for the steel flares? Which ones are they?
Thanks
-James
What kind of bumpers do you have? I've been looking for a set (F/R); either
chrome(at the right price) or fiberglass.
Thanks
- Chris
PS: Too bad about the project, but I know how those things go.
Looking for door panel parts . How much for the steel flares. What type of rims? Any front or rear sway bars?
Need Rear 1/4 panels do you have F/G or steel?
How much for steel fenders
Sorry to hear you're not going to finish it, Ed ...
I am interested in the flares, how much?
I've been getting tons of PM's for parts and prices. Stand by, I'll be posting a list of items with pricing soon.
Stay tuned.
Ed
Interested in the tub.
Here is my 1st phase of itemized parts with pricing.
PATRICK MOTORSPORTS PARTS
These parts are brand new and still in their boxes.
1. Oil filler neck kit - $158.00
2. 914-6 Conversion Oil Tank Aluminum - $735.00
3. 914-6 Oil Filter Console - $155.00
4. 914 GT Oil Cooler Kit - $790.00
a. SETRAB GT Oil Cooler
b. GT Shroud Kit ( 2 part fiberglass)
c. Electric Pusher Fans 6.5" - 2 fans
d. S.S. Mesh Sheet
FACTORY BLACK 1973 914 TUB (L041)
1. Patrick Motorsports Engine Carrier Mount (welded in) - $458.00
2. Restoration Design floorboards (welded in) - $450.00
3. New cross member repair (welded in) - $220.00
4. Floor Pan Reinforcement (welded in) - $55.00
5. Chassis Stiffening Kit (welded in) - $185.00
6. Rear Floor Pan Triangle, Right (welded in) - $82.50
7. Engman Inner Long Kit (welded in) - $180.00
8. Reproduction 914 GT Steel flare (not installed) - $1025.00
TOTAL IN ADDED PARTS - $2655.50
The tub still has few issues. Typical rust in the trunk that needs to be addressed and front suspension points appear to have been slightly hit from underneath. Possibly PO went over a parking lot cement stop. Hell hole has been been repaired and longs have been cleaned and coated with Eastwood's Internal Frame Coating. Dash, heater controls and wiring are still installed. Show up with a trailer, a way to move the car from my garage and $2500 TAKES TUB AND FLARES.
1987 PORSCHE 911 FRONT SUSPENSION
1. 911 Front Suspension Complete w/ lower sway bar - $800.00
2. New Bilstein Front Struts (2) - $290.00
3. New Elephant Racing PolyBronze Bearings - $260.00
4. New Turbo Tie Rod Ends - $65.50
5. New Underbody Sway Bar Bushings (4) - $20.00
6. PMB Rebuilt Front A-Calipers Yellow Zinc - $269.00
7. New Crossed Drilled SEBRO Front Rotors (2) - $188.00
TOTAL 911 FRONT SUSPENSION REBUILT INVESTED - $1892.50
This front end is pretty much ready to go. Bolt on breaks and rooter and you're good to go. I will let this front end go for $1500. This would be better than new.
QRS FIBERGLASS PARTS - 914-GT STYLE / NEW NEVER USED
1. Front Hood - $325.00
2. Rear Deck Lid - $325.00
3. Front GT Bumper - $200.00
4. Front GT Valance - $135.00
5. Rear GT Bumper - $200.00
6. Side GT Rocker Panel - $150.00
I'm hoping to at least get what I've paid for this minus the freight. Would like local pick up.
So sorry that you are not able to complete this project. Best of luck in the sale.
Bolt on breaks and rooter - maybe that was the issue
GLWTS
Ed, what are you asking for the Setram Gt oil cooler and the S.S. mess. John
I'm looking for a set of centerlines in the 5x130 pattern. I can ship other five lug wheels with tires mounted to keep your shell a roller. Can we make a deal?
Do have any engine parts like cylinder heads?
Thanks,
Do you have the ca. 6" circular front floor plate, part #91455924710, that looks like this:?
Keeping my fingers crossed,
Skip
Do you have the bumpers? Are they chrome or painted? How much for each?
Thanks,
Ken
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)