Printable Version of Topic

Posted by: bdstone914 Oct 8 2014, 12:13 PM

I have a black 75 and a yellow 74 that are being cut up for parts. Many parts are already gone. The 75 has the front fenders cut off but are still available. The passenger quarter is gone. Not a lot of rust on most of the car.

The yellow 74 car has the passenger fender, rear trunk panel. pedal area and front passenger pan, and firewall cut out.

I can cut out sections as needed. Since a price is required I will say $50 -200. The price depends on the difficulty of cutting out the section and the size.

I can send pictures of specific areas. PM your email address.

And yes there is a good story that goes with the tire in the front trunk of the yellow car.

Bruce


Attached thumbnail(s)

Posted by: Sleepin Oct 8 2014, 12:39 PM

Hey Bruce, how is the passenger side cowl, fender seam area on the yellow car? I'm not 100% sure I need to replace mine, but it's close.


Attached image(s)

Posted by: ndfrigi Oct 8 2014, 12:58 PM

Sir, thus the 74 yellow has a good rear passenger side ear suspension? How much ship to 90630? God bless! Noel

Posted by: AvalonFal Oct 8 2014, 01:30 PM

What would LS inner wheel well on the '74 and shipping to 19136 cost? Here's what I'm trying to replace.

Posted by: Brian_Boss Oct 8 2014, 02:05 PM

If either car has a good front trunk floor i would want that and also the piece of the engine shelf near the battery tray that typically gets cut out for A/C installs. I can take a picture to clarify.

Shipping to 75214

Thanks,
Brian

Posted by: rstover Oct 12 2014, 04:19 PM

Looking for front left channel and a small area above and in front of left rear tail light housing

Posted by: Zinergy69 Oct 12 2014, 10:39 PM

I'm looking for the piece outlined, the shock if in good shape and the gusset just below. PM me with cost... I go to Riverside often, I can pick it up.
Thanks!

Posted by: rohrer914 Oct 13 2014, 09:14 PM

how about the fuel pump hatch door?.
I'm also looking for one engine lid hinge brake.

Posted by: OllieG Oct 14 2014, 03:36 AM

Hi Bruce,

How's the rear drivers body panel below the sail panel on the yellow car?…I'm looking for a section between the rear arch and door jamb.

Thanks.

Posted by: bdstone914 Oct 14 2014, 10:34 AM

The fuel pump cover is sold.
Just by the engine lid bracket new from Restoration designs. They are not that much.

Posted by: barebrad Mar 19 2015, 05:12 PM

Are you still cutting? I'm looking for the engine mount bracket under the battery tray?
Let me know if this is available.

Posted by: bdstone914 Mar 19 2015, 08:30 PM

Pm sent. Yellow 74 is cut into chunks. Black 75 about the same as pictured.
Bruce

Posted by: shuie Mar 20 2015, 07:26 AM

I need two of these if you still have them. The channel shaped bracket that is welded to the cross member w/toothed height adjuster. Shipped to 70769 please.

Posted by: 80cap Mar 20 2015, 07:50 AM

DO YOU HAVE THE 2 REAR TARGA LATCHES
BRIAN

Posted by: bdstone914 Mar 20 2015, 01:52 PM

Yes i have refinished rear targa latches for $60 a pair shipped. Can post a picture later.

Posted by: 914Sixer Mar 20 2015, 07:07 PM

Bruce,
How is the rear trunk floor on the 75? They are quite a bit different than the early ones.

Posted by: Jw4129 Feb 13 2018, 10:29 AM

I am lookin for all targa latches...

Posted by: bdstone914 Feb 13 2018, 04:08 PM

PM sent, BTW this ad id three years old so not much is left from these cars but I have lots of 914 parts.

Posted by: Nacho Feb 13 2018, 05:14 PM

Hi Bruce

How much for this area?



Thanks

Posted by: VRROOMM1 Feb 17 2018, 11:52 AM

how much for the trunk hinges?

Posted by: bdstone914 Feb 17 2018, 04:51 PM

Which ones ? front or rear? $25 shipped for either pair. I have several sets.
Bruce

Posted by: mgp4591 Feb 18 2018, 08:43 AM

Hey Bruce, how about a solid pedal box?
Thanks, Mike

Posted by: bdstone914 Feb 18 2018, 09:50 AM

I assume you mean the sheet metal where the pedals install ? I have a parts car with a good section. Send me a picture of the area where you want it cut.
Bruce

To all,
This post is over two years old. Most of the parts on these cars are long gone. I still have three parts cars and can still supply supply many parts.

Posted by: rick 918-S Feb 21 2018, 04:04 PM

Do you have a clean right rear floor pan? Fixing a really clean factory 6. Just a few small issues. I would rather piece in a section than use a RD panel.


Attached thumbnail(s)