914World.com [Powered by Invision Power Board]

Posted by: getkirk May 9 2016, 10:49 AM

My muffler has shaken itself to bits on what passes for roads in the great state of Vermont. Would like to find a Bursch, but I am open to anything that is not too loud and will fit. (early 1.7/1.8 4" bolt spacing)
Thanks!

Posted by: rhodyguy May 9 2016, 11:29 AM

You'll have better luck if you provide info on the type of heat exchangers that are on your car. If you're unsure, post a picture of the muffler ends.

Posted by: mhenderson57 May 13 2016, 10:11 AM

QUOTE(getkirk @ May 9 2016, 12:49 PM)

My muffler has shaken itself to bits on what passes for roads in the great state of Vermont. Would like to find a Bursch, but I am open to anything that is not too loud and will fit.
Thanks!

I have a Monza muffler that I am going to sell. Like new condition. $150 + shipping.
Cost $302.58 new.

Thanks,
Matt

Posted by: getkirk May 13 2016, 03:21 PM

QUOTE(mhenderson57 @ May 13 2016, 09:11 AM)

QUOTE(getkirk @ May 9 2016, 12:49 PM)

My muffler has shaken itself to bits on what passes for roads in the great state of Vermont. Would like to find a Bursch, but I am open to anything that is not too loud and will fit.
Thanks!

I have a Monza muffler that I am going to sell. Like new condition. $150 + shipping.
Cost $302.58 new.

Thanks,
Matt

Hi Matt, my old one was a Monza and I was hoping to move away from the Quads. But I will keep you in mind.
Thanks,
Kirk

Posted by: forrestkhaag May 15 2016, 06:54 PM

I have a set of very decent 1.7 headers mated to a barely used Magnaflow muffler and pre-resonator using a Bursch stock collector pipe setup.. A nice throaty sound with not too much noise for day to day use. I can send pictures if interested in the set and would like to get 300.00 + shipping CONTUS

Oh,.. and the tail pipe is chrome tipped and fits the non-early rear valance verses the early hole thru the valance..

Have a good day.

Posted by: greggearhead May 15 2016, 07:15 PM

I've got several Bursch for the 4-inlet trapezoid style heater box outlets. Is that what you are looking for?

Posted by: Wyvern May 16 2016, 12:01 AM

^^^ I am also after a muffler (will not jump in front of this OP)... but if you have multiple would like to see what you have)
Found this in the forum . can you measure what you have . & hope this is helpful to others.

IPB Image

Posted by: bdstone914 May 16 2016, 04:50 AM

What year car and what engine? They are not all the same.

Posted by: Papermaker May 16 2016, 07:32 AM

HI getkirk--

Have a 1.8 L Bursch. PM me when you figure out what type your looking for.

--Papermaker

Posted by: getkirk May 16 2016, 01:25 PM

QUOTE(bdstone914 @ May 16 2016, 03:50 AM)

What year car and what engine? They are not all the same.

The car is a 1975, the HE were replaced with the early style double pipe. 1.7-1.8.
Distance between lower bolt holes is 4 inches.

Posted by: getkirk May 16 2016, 01:48 PM

QUOTE(Wyvern @ May 15 2016, 11:01 PM)