Printable Version of Topic

Posted by: rwfms Feb 15 2017, 10:38 PM

Garage reduction sale. Most parts from '73 1.7or a '76 914. More photos available by request. PMs welcome . Located in Derby KS 67037 (Wichita). Buyer pays shipping. Many other 914 parts later.

1. Weber 40 IDF setup.----$360 SOLD
Purchased new. Worked well on my ‘73 1.7 until engine broke, did a 6 conversion instead. Carbs are in very good condition with no play in the butterfly shafts. Made in ?? On the shelf about 10 years, will need rebuild kits and air filter elements.

3. 009 distributor for dual carbs----$50
4. 050 Distributor for dual carbs----$50 SOLD
5. Bosch stock 1.7 vacuum advance distributor ----$25
6. 5-lug Fuchs replicas, steel stems, very nice set. (2) 7x15, (2) 8x15 ----$400 SOLD
7. ’73 1.7 engine tin – ten pieces . Solid, straight, surface rust, no rot----$35 SOLD
8. Heat exchanger heater ducts – six pieces ----$35
9. Heat exchangers – pair ----$30 SOLD
10. Exhaust pipe & muffler, good condition, nice sound ----$35 SOLD
11. Exhaust pipe & muffler – rough ----$10
12. Motor Mount cross bar only ----$25 SOLD
13. Rubber motor mounts – pair ----$15 SOLD
Both 12. and 13 ----$35 SOLD
14. Engine bay Blower, very good ----$35 SOLD
15. Engine bay blower, good motor and fan, loose fan shaft bearing ----$10 SOLD
Both blowers ----$40 SOLD
16. Firewall sound deadener blanket, nice condition ----$30 SOLD
17. Rear luggage pad and floormat ----$25 ea. $45 both SOLD
19. Window glass set from ‘72 914, no windshield. Exceptional condition ----$85
L&R tinted window glass SOLD
L&R tinted vent glass SOLD
1 clear back glass
20. Other window glass, original VW/Porsche
1 early clear driver side window w/bracket ----$25
1 late clear passenger side window w/brackets ----$25
1 clear back glass ----$25
1 NOS tinted L front vent glass w/original brackets, rubber seal and manufacturer’s label. Still has some rubber protectant goo on the seals ---$40
21. Trailing arm stiffener plates – pair ----$50 SOLD


Attached image(s)

Posted by: Jett Feb 15 2017, 10:59 PM

Hello, I'll take #12, 13, 16 and 17 please.

Shipping to 98073

Please PM.

Cheers

Posted by: N_Jay Feb 15 2017, 11:15 PM

How well did those wheels work?
Spacers? Tire size?
Did you have to flair at all?

Posted by: brant Feb 16 2017, 12:05 AM

I'd like the 050 distributor to 80503. (Colorado)
Brant

Posted by: euro911 Feb 16 2017, 01:04 AM

Damn ... I need # 13. Rubber motor mounts – pair ---- $15 ... if Jett passes

I'll grab # 17. Rear luggage pad ... (the rubber one) ---- $25 ea.

Posted by: sterr11 Feb 16 2017, 05:43 AM

I'll take 14 and 15.

Posted by: 74ravenna Feb 16 2017, 06:00 AM

Item #7 Please (engine tins)

Thanks

Posted by: mepstein Feb 16 2017, 07:14 AM

If you have the early metal brackets for the window glass, I'll buy them.
Thanks, Mark

Posted by: JOEPROPER Feb 16 2017, 08:09 AM

#6 Do you have the center caps? Have they been spun and checked for streightness?

#10 and #11 What year? I have a "75 2.0...

Thanks.

Joe

Posted by: eric914 Feb 16 2017, 09:30 AM

Ill take #6

PM sent

Posted by: rwfms Feb 16 2017, 10:06 AM

PM sent

Posted by: Wayne Feb 16 2017, 10:21 AM

#19 Please if Mepstein backs out

Posted by: rwfms Feb 16 2017, 10:52 AM

You got em. PM sent

Posted by: rwfms Feb 16 2017, 10:53 AM

Will do.
Thanks

Posted by: rwfms Feb 16 2017, 11:05 AM

PM sent

Posted by: rwfms Feb 16 2017, 11:07 AM

Sorry, talk to Jett

Posted by: rwfms Feb 16 2017, 11:11 AM

Joe, The heat exchangers and exhaust will not fit your 2.0. Thanks for your inquiry on the wheels, have a buyer.

Posted by: rwfms Feb 16 2017, 11:46 AM

PM sent

Posted by: rwfms Feb 16 2017, 01:16 PM

N Jay, these would be more for a flared car. I'm not an expert on clearances but I know guys who have put 7 inchers on the rear by bowing the fenders out slightly. Not sure if you could do the same in the front but the 8 inchers definitely wouldn't work. I am running wider wheels with flared quarter panels and I didn't use these on my car. Thanks for your interest.

Posted by: euro911 Feb 16 2017, 01:40 PM

I didn't notice that he grabbed #17 as well ... I guess I'm getting old

Posted by: brant Feb 16 2017, 04:36 PM

rwfms,

oddly I didn't get a Personal message
maybe my box is full or something
I will send you one
thanks
brant

Posted by: rwfms Feb 16 2017, 05:09 PM

PM sent

Posted by: rwfms Feb 16 2017, 05:13 PM

Sorry I'm having trouble with PM. I will get a shipping quote and try again.
Ron

Posted by: forrestkhaag Feb 16 2017, 09:17 PM

I would like to purchase 21 stiffening kit to 92651. I can PayPal or other after confirmation of shipping add on . Cheers.

Posted by: rwfms Feb 16 2017, 10:23 PM

Sorry, they are already taken. Thanks so much for the reply.

Posted by: Tbrown4x4 Feb 17 2017, 03:53 AM

Interested in #9 and #10. I'll PM you for shipping info.

Posted by: AZBanks Feb 17 2017, 09:32 AM

What parts do you have left?

Posted by: rwfms Feb 17 2017, 02:10 PM

I will post SOLD soon as I figure out how to edit the original post. I know it's here somewhere. Help?

Posted by: mepstein Feb 17 2017, 02:27 PM

Posted by: brant Feb 17 2017, 03:03 PM

Ron,

if your logged in (with password)
then there is an edit button on the bottom right of the post
and you should be able to add or remove text in the edit screen

Posted by: forrestkhaag Feb 17 2017, 03:14 PM

And please let us know how to recieve shipping cost to add to purchase cost. thanks

Posted by: rwfms Feb 17 2017, 08:53 PM

Thanks Brant!