Printable Version of Topic
Click here to view this topic in its original format
914World.com _ FS/WTB: 914 Parts _ WTB: Shaft Radio Faceplate
Posted by: 914Sixer Mar 28 2018, 03:14 PM
Need one of these. Not cut up ones please. Somebody enlarged the holes on this one.
Attached image(s)
Posted by: Mike Fitton Mar 28 2018, 03:41 PM
No those holes are correct for an early cars with the chrome trim that installs from the front. What Radio are you installing?
Posted by: 914Sixer Mar 28 2018, 04:17 PM
Chrome nose Becker radio with standard shaft.
Posted by: 914Sixer Apr 2 2018, 09:18 PM
Still looking
Posted by: rgalla9146 Apr 3 2018, 06:05 AM
Still looking
Do you know the diameter of the shaft holes ?
I'll check.
Posted by: 914Sixer Apr 3 2018, 06:45 AM
Rory,
I just need ones with the regular holes. This plate is the only example I had. I need the ones with rounded corners where the radio nose goes thry. Reproductions are incorrect, they have square corners and are too large.
Posted by: rgalla9146 Apr 3 2018, 01:31 PM
Rory,
I just need ones with the regular holes. This plate is the only example I had. I need the ones with rounded corners where the radio nose goes thry. Reproductions are incorrect, they have square corners and are too large.
Mark
Here's what I can offer.
I've concentrated on Blaupunkt Frankfurts ...not Beckers
The upper one is aftermarket and heavier.
The lower is real ....but the face hole has square corners.....can it work for you ?
Posted by: 914Sixer Apr 3 2018, 04:48 PM
Not seeing the pictures.
Posted by: 914Sixer Apr 12 2018, 06:42 PM
Still needing one good one. If I can get a good one maybe we can get it reproduced the correct thickness and rounded corners.
Posted by: Mike Fitton Apr 12 2018, 09:50 PM
Here you go: https://www.ebay.com/itm/6070s-Porsche-914-Faceplate-for-Blaupunkt-Frankfurt-Radios/302678586164?hash=item46790cb334:g:m8oAAOSwr21amtAy&vxp=mtr
Posted by: Garold Shaffer Apr 12 2018, 10:29 PM
let me check my stash of parts in the morning.
Posted by: 914Sixer Apr 13 2018, 06:34 AM
Thanks Garold.
Posted by: 914Sixer Apr 23 2018, 08:12 AM
Posted by: PCA7GGR Apr 23 2018, 10:53 AM
Let me know if this ones works for you. The desired cutout is outlined on the back. Thanks
Sergio
Posted by: 914Sixer Apr 23 2018, 07:07 PM
I will keep this one in mind. Hoping to find punched one with small holes.
Posted by: McMark Apr 24 2018, 02:03 PM
I have these reproductions I made. $15 http://PayPal.me/OriginalCustoms/15 Have 8 in stock. They're zinc plated too.
Attached thumbnail(s)
Posted by: Mikey914 Apr 25 2018, 12:42 AM
I know we did a run of them too, I'll have to check with Scott to make sure, but we can do the correct early vinyl and provide with self adhesive backing. We did jump down a gage on the metal so slightly thicker, and very sturdy.
Posted by: Mikey914 Apr 25 2018, 11:29 AM
I know we did a run of them too, I'll have to check with Scott to make sure, but we can do the correct early vinyl and provide with self adhesive backing. We did jump down a gage on the metal so slightly thicker, and very sturdy.
We have these and can add the correct vinyl and adhesive tape to the back for $25.00. That includes shipping. If this works I just need your email address to send you a PayPal invoice, and your shipping address.
Posted by: Garold Shaffer May 1 2018, 01:12 PM
let me check my stash of parts in the morning.
Final found it. If you haven't found one yet PM me. $30 includes shipping to you.
Attached thumbnail(s)
Posted by: 914Sixer May 1 2018, 04:59 PM
Yes that is the correct one.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)