Printable Version of Topic

Posted by: brant Feb 5 2020, 01:38 PM

so I have the typical parts (suspension) that I'm willing to give away

I'm not willing to ship all of this... packaging it would be a nightmare

but if you need something... we can maybe work out a connection, or short term storage... etc. just reach out, i'm reasonable

I'll put pictures up

-rear stock coil overs... hardware on top and bottom if someone needs a piece of it

- a couple of sets of loaded A arms... both sets have sway bar tabs, torsion bars in good useable shape, and end caps etc. both were late wedge pin arms if that matters

-4x front struts. complete.. hardware... I'm going to pull the rotors before I dump them, and take off a few bits, such as wheel bearing collars.. if you need a top mount, piece of hardware, etc.. let me know

-mufflers... I have various ones... doubt someone really needs an old muffler but if you have a project in mind, etc? I have measured and have 2.0 spacing, and also 1.7 spacing... old crusty mufflers... maybe you want a flange?

75-76 heat exchangers... some of the ends are rusty and clamped... but they also have bits of tin work on the ends if you need that …. oh... also lots of stub pipes


anyways I'll post pics
I'm sure i left something out
but reach out if you need any of it before I haul it away in the future
brant


Attached thumbnail(s)

Posted by: brant Feb 5 2020, 01:39 PM

and


Attached thumbnail(s)

Posted by: brant Feb 5 2020, 01:50 PM

and



Attached thumbnail(s)

Posted by: Shindog1961 Feb 5 2020, 03:04 PM

Where are you in Colorado?

Posted by: brant Feb 5 2020, 03:21 PM

Longmont.
north of Denver
80503

but I travel around in state too
and could always hold for a convenient time also
depending on space... I hope to put my car together in time for the spring RT66 in ALBQ. (no guarantees I'll have the wiring repaired in time)

brant

Posted by: Chris914n6 Feb 5 2020, 04:22 PM

If we both make it to Rt66....

I have a car that can use the a-arms w/ sway tabs and you can have the Rivs we talked about not long ago

Posted by: brant Feb 5 2020, 04:25 PM

sounds good to me
I'll set back a complete set of arms/bars/torsion caps...
brant

Posted by: brant Feb 6 2020, 10:35 AM

looks like there are claims on 1 set of a-arms, 1 set of struts, and 1 muffler....!

Posted by: 914 Pikachu Feb 7 2020, 11:31 PM

Interested in 75-76 heat exchangers with stub pipes to match. How much to pack and ship to Vermont 05450. Thanks, Perry

Posted by: Krieger Feb 8 2020, 08:56 AM

I'd like the other pair of a arms, no torsion bars. If you willing to ship to ca.

Posted by: brant Feb 9 2020, 08:42 AM

Perry,

sorry for the slow reply
I finally did a bunch of packing yesterday and a bunch of examining also

so I would advise against taking the 75 HE
the boxes are loose... they are clamped
Really not in good shape

the 75 style is a terrible design
you would be better served upgrading anyways to the early design exchanger

and due to the rust... I don't think these are worth a big shipping bill

sorry, but I'd hate for you to pay 75-100 shipping and then they would be rusted out anyways....

let me know if you disagree
but these boxes are mostly used up
brant

Posted by: brant Feb 9 2020, 08:42 AM

Andy,
I'll send a pm

Posted by: 914 Pikachu Feb 10 2020, 08:12 PM

Brant, thanks for the advice I will pass and look for the older heat exchangers then.