Printable Version of Topic

Posted by: brant Nov 29 2022, 05:42 PM

not sure what to call this....
mine must have vibrated loose and fell off somewhere between colorado and SLC for the Red Rocks event....

does anyone have a spare to sell?

its the cover plate that attaches to the S-bend on the rear attachment point
to connect the HE with the S-bend for the heater system...


thanks in advance
here is the picture of the one plate I have.. and the smaller one I need.


Attached thumbnail(s)

Posted by: PCA7GGR Nov 29 2022, 05:52 PM

PM me if this is the part you need - thanks

Posted by: 914Sixer Nov 29 2022, 06:07 PM

Reproductions are available new. About $13. Heritage Parts Center


Attached thumbnail(s)

Posted by: GaroldShaffer Nov 29 2022, 06:32 PM

There is a difference in size left VS right. Left side is 3 1/8 inches between hole centers VS 2 7/8 on the right side. Make sure you get the correct one. I too have these available.

Posted by: brant Nov 29 2022, 06:44 PM

Thank you everyone

I need the drivers side small end

I measured Hole to hole at 2 and 3/8

Pictures I should have taken earlier



Attached thumbnail(s)

Posted by: brant Nov 29 2022, 06:44 PM

And


Attached thumbnail(s)

Posted by: brant Nov 29 2022, 06:47 PM

I should add

Used is fine for a driver car like this one

Posted by: PCA7GGR Nov 29 2022, 06:52 PM

Mine is 3 1/8 inches between hole centers.

Posted by: brant Nov 30 2022, 08:01 AM

My mistake
I couldn’t tell the dimensions well on yours and did not pm
But will send that message now.
Thank you!

Thanks everyone
Brant

Posted by: brant Dec 1 2022, 09:46 AM

bump...


still looking for the small end... driver side/Left

Garold, sent you a pm to see if you have one for sale also

brant

Posted by: brant Dec 2 2022, 07:39 AM

Still looking

Bump

Posted by: brant Dec 3 2022, 08:02 AM

Weekend bump

Posted by: TheCabinetmaker Dec 3 2022, 08:16 AM

I might have one, Brandt. I'll look in a bit

Posted by: TheCabinetmaker Dec 3 2022, 10:17 AM

Found one. Removed this from a driver's side "s" pipe

Posted by: brant Dec 3 2022, 11:42 AM

Curt

Thank you so much

It’s hard to tell length in a photo
Would you also mind checking the length between the bolt holes?

The one I need goes on the rear of the S connector with 2 and 1/4 bolt spacing

Thank you against n Curt
I’m excited to put things back together and move to the next project on the list

Posted by: TheCabinetmaker Dec 3 2022, 12:21 PM

Brandt, the holes are 3⅛ inches on center. It came off the the driver's side pipe from the fan shroud. I have a pair of repops. Neither are 2¼ inches

Posted by: brant Dec 3 2022, 12:33 PM

No problem Curt

Mine takes that size on the fan shroud end too
But the smaller size on the end that connectsn to the HE

I’m guessing it’s the small one that frequently vibrates loose and gets lost (like mine)

Where did you buy the repops?
Looks like I need to do that

The link in this thread is in Europe…. So I’ll see if there is a US option that doesn’t want more for shipping than the part costs

Posted by: TheCabinetmaker Dec 3 2022, 12:44 PM

Gotcha. The other end is just a piece of bent sheet metal. It's not like the shroud end. I'm not home till later. I'm sure to have one.

Posted by: brant Dec 3 2022, 12:53 PM

I thought about making one because it’s simple
But I’m lazy

No rush
But if you do have an extra I’m a customer!

TIA
Brant

Posted by: GaroldShaffer Dec 4 2022, 08:33 AM

I need to work on my reading comprehension. This is what your are looking for?




Attached thumbnail(s)


Attached image(s)