Printable Version of Topic

Posted by: J P Stein Sep 29 2009, 09:47 AM

GA mainshaft gearset......excellent. $350

2 intermediate plates with good bearings
early $200 (tapped hole for -6 throttle linkage)
late $150

F mainshaft gearset....very good $200

'B' first gear set....less reverse, excellent $300

Lots of other gearsets @ $100.....all very good or better.
Also spare cases and R&Ps....cheep.

All of the above have VG dog teeth & syncros.

R & Ps are NOT sold.

All above + shipping.

I don't do Pay Pal.

Posted by: DNHunt Sep 29 2009, 03:05 PM

Hey JP

You got 3rd gear L preferrably or M?

How about T 4th?

Dave

Posted by: koozy Sep 29 2009, 04:35 PM

I'm looking for M-S-X. Any or all. Let me know what ya have and I'll send ya a check. I have your address.

Thanks.

Posted by: J P Stein Sep 29 2009, 05:50 PM

None of those, guys. All of the 100 buck sets are stock 914 box sets.

Posted by: koozy Sep 29 2009, 10:03 PM

I figured. It was worth a shot... ha ha ha

Posted by: carr914 Sep 30 2009, 06:19 AM

Got a Billit Intermediate Plate hiding in a box?

T.C.

Posted by: J P Stein Oct 1 2009, 06:55 AM

QUOTE(carr914 @ Sep 30 2009, 05:19 AM)

Posted by: J P Stein Oct 17 2009, 04:44 PM

The R & Ps are solt.

Still have the rest of the stuff. I'll even throw in a slider assy with the gearsets....till they run out.

I wanna move this stuff so I'll entertain decent offers.....even for all......bout 75 lbs worth.

Posted by: dangrouche Oct 17 2009, 10:41 PM

so how much for a stock 1st gear & good dogteeth with its mating gear, a 1st gear slider, both items with sharp teeth, and for two good syncros. i figure a flat rate priorty mail shipping box should contain this stuff. I guess a postal money order is the way you want money? TIA for response

Posted by: J P Stein Oct 18 2009, 09:44 AM

I have good 1st gear sets but no slider....those are tough to come by and THE part in demand. Dr. Evil has a source for new ones.

Posted by: pete-stevers Oct 18 2009, 10:41 AM

do you have any tranny rebuilding tools?

Posted by: bag5rcg Oct 18 2009, 03:02 PM

Would you have any end covers?...Mine has a busted ear...

Posted by: J P Stein Oct 18 2009, 05:19 PM

The only rebuild tools I have left are those for checking backlash.....home made rig.

I have 2 end covers for side shifters. $25 each + shipping.

Posted by: pete-stevers Oct 18 2009, 11:48 PM

how much do you want for it?
nuttin the matter with homemade

Posted by: J P Stein Oct 19 2009, 10:15 AM

The pricy bit is the dial indicator set up. As you can see in the pic, it is mountable bout every where and the arm flexs & locks in place. It also works great for setting cam timing on a 911 engine...which is why I bought it.

The bcklash set up is stuff I fabbed (no rocket science here). The blue tape is no longer there. JB weld (with a release agent) in the 30mm socket took care of the "no wiggle" on the expansion bolt......note, there is no speedo drive in the bolt.

$100 + shipping


Attached thumbnail(s)

Posted by: zig-n-zag Oct 19 2009, 12:59 PM

PM sent

Posted by: J P Stein Dec 5 2009, 10:13 AM

Bump
Still have trans bits.