Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ testing parts, is there a good way and bad?
Posted by: Gigamight Jun 24 2010, 09:16 AM
I want to test some things like headlight motors, fresh air box, etc. before I install them. Especially the fresh air system, since it is such a pain to put together. Can I safely test them on a bench with a 12 volt power source? If so, where can I find some pinouts for correct connections?
Posted by: vsg914 Jun 24 2010, 09:28 AM
Short answer, yes. 12 volt source? Small jumper cables ( zip cord and aligator clips).
Posted by: tradisrad Jun 24 2010, 09:36 AM
When I checked out my roller's wiring i just put the battery in and checked the lights, blower and anything else that could be powered up.
haynes manual should have the wiring diagram for the fresh air blower etc. besure to oil the bearing.
also with the the fresh air box, if you dont have the screen add one. I went as far as adding some black screen (door) mesh over the factory leaf screen. if you have an early car you can get a late gasket and fit the factory screen. and make sure you get a good seal as it's a great place for water to enter. don't forget to check the blower switch plate; they often are filthy.
Posted by: 70_914 Jun 24 2010, 11:30 AM
It's all about the power probe for this kind of work. Looks like a test light, but has positive and negative leads. Hook it to a battery and there is a rocker switch to add power and ground to the tip, and it is fuse protected (so you don't burn up your car/parts during testing).
Picked mine up pretty cheap because there are more advanced models on the market now.
Posted by: windforfun Jun 24 2010, 11:41 AM
Let the stuff run overnight (if appropriate).
Posted by: Gigamight Jun 24 2010, 12:46 PM
It's all about the power probe for this kind of work. Looks like a test light, but has positive and negative leads. Hook it to a battery and there is a rocker switch to add power and ground to the tip, and it is fuse protected (so you don't burn up your car/parts during testing).
Picked mine up pretty cheap because there are more advanced models on the market now.
Where would I get such a thing? Sounds perfect. Harbor Freight have anything like that I wonder...
I currently have no body harness installed, because I am swapping it out, otherwise I would just hook up the wires and a battery and go to town.
Posted by: vsg914 Jun 24 2010, 01:24 PM
Make one.
Posted by: Gigamight Jun 24 2010, 01:39 PM
Make one.
..........
I think maybe I have misrepresented myself, I'm not that smart. Luckily, I'm ok with that. But it does put me at a disadvantage when it comes to building such a device without a detailed diagram. I am probably looking at buying such a thing instead. Unless someone has one that I can borrow
Posted by: 70_914 Jun 24 2010, 05:40 PM
It's all about the power probe for this kind of work. Looks like a test light, but has positive and negative leads. Hook it to a battery and there is a rocker switch to add power and ground to the tip, and it is fuse protected (so you don't burn up your car/parts during testing).
Picked mine up pretty cheap because there are more advanced models on the market now.
Where would I get such a thing? Sounds perfect. Harbor Freight have anything like that I wonder...
I currently have no body harness installed, because I am swapping it out, otherwise I would just hook up the wires and a battery and go to town.
Google search shows that Amazon sells the power probe. Got mine off the Snappy truck.
Kevin
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)