So, I restored a few of the early fog lights for a project I'm working on, and it dawned on me that this would be a perfect situation for a GB.
I would include a new seal for the glass and new grommet for the wirring.
I would need you to dissassemble the unit and send in only the main body, ring and mounting bracket.
You would recieve a professionally powdercoated assembly in return with a gasket for the glass and a grommet for the wirring. Cost would be $15 per assembly and return shipping at cost USPS priority mail with tracking.
You would get back something that looks like this
Attached thumbnail(s)
The powder is BK-08 Black. And the grommets are a nice tight fit.
Attached thumbnail(s)
ha, I just ordered foglight seals.. I was gonna rattlecan mine.. but if you're going to do them all up nice.. I'm in.
I probably have some spares lying around I can dissect, then assemble the best-of-the-parts.
I figured that as I was doing some BK-08 I should have some of these done at the same time. If I can get 10 sets it would be worth doing. I figured it would be ince to be able to have these blasted down to the metal and the professionally finished.
the only downside is that if there is a lot of rust, you may want to check to make sure it's not all the way through. Ask me how I know.
Mark, I'd go in for this. I can send a pair of fog light parts, just say when.
I'm in for a set.
Jim
Well, that looks like 6 sets are in.. Mark says he needs 10. Anyone else?
Everyone go out and look at the leading edges of your fog lights - you will be mortified by how sand blasted and rusty they are. Then sign up.
I'm in for a set.
I'm in for 2 sets
Looks like we are pretty close and this will pan out. I'm thinking that to keep these straight it would be worth scribing initials on the inside on the plate where they will not be coated. Is this ok with everyone?
Also,
The amount of rust on the units will determine the success of the finish, ask me how I know. This was pretty bad to start with, but I'll use some silicone to patch it on mine.
I would ask on these that they be accompanied with a check or money order as to not have any paypal fees as you have to ship these anyhow.
Thx
Mark
Attached thumbnail(s)
I will do 2 sets
Thank you
I'll have to find them, but I do have a pair of fog lights that would benefit from this
Put me down for 1 pair please.
Sorry for the stupid question but the only way to remove the fog light from the car is to cut the harness ?
No you have to remove the lenses and unscrew the wire posts
Do i need to remove the front bumper to get the foglights out ... (never removed any before)
I'm in for one set.
I'm in for a set. where do I ship them to?
Is this going to be a go?
Is it too late to get on board with this GB?
Thanks
David
Yes this is a go. I'll start PMing the shipping info tomorrow. I plan to keep this open until the end of the month to give a chance for a few more to get in on this.
-Mark
I know I have an old pair boxed up somewhere. If I can find them I will join the group buy. I'll verify by this weekend. Thanks, Mark, as usual!
Yes, These are going to go now.
just needed to clear my schedule a bit.
I'm sending a message to each one of you with my address. Simply send in your units to be stripped and coated COMPLETELY dissasembled. Include $15 per unit and include what you paid for shipping (include tracking ) to the total. Please send a check or money order no need to use paypal as you'll have to send in the units anyhow.
-Mark
I have recieved lights from
Euro 911 1 set
Jentz 2 sets
Harmon 2 sets
Lui 2 sets
I imagine that there will be a few more soon, so 10 will not be a problem. I'm looking at dropping these off the 1st of April. GB cut off will be at my door March 30th so I can get these set up to go.
-Mark
Pulled & stripped mine today, they'll be on the way tomorrow.
Thanks Mark.
2 sets Tolentino - Please call me Yours were recieved today
Mitsch recieved 1 set
Knight 1 set
Mark, From the above it looks like this GB is still going on ? I have a set of 2 to send it, will ship these right away to you so you get them this week. Please email me payment and shipping address.
TIA.
OK,
I got enough in to make this happen. For those that didn't have clear markings I added a small scribe on the inside of the rings and the mount inside of the main housing.
Here's the breakdown-
Euro911- 2 housings and 2rings
Knight - 2 housings and 2rings - You left 8 springs in, they will be returned.
Calkins - 2 housings and 2rings + 2 bases
Lui- 4 housings and 4 rings +4 bases
Jentz and Meridith 4 housings and 4 rings
Plasket-2 housings and 2rings
Mitsch2 housings and 2rings + 2 bases
Harmon 2 housings and 2rings
20 unist - going in tomorrow - should be ready in about a week.
These are done. I will be picking them up On Wed morning when I get back in and getting them shipped out !
Got these back this week. I had to have them recoated as they had bubbles in the 1st run. I'm getting these packed up tomorrow and wil be getting them out in the next few days.
-mark
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)