Quik search reveals HL switch a common point of failure.
Long NLA, I saw a late-model NOS selling for $285, which is less than the last OEM price. Way too much for me, and I have an early switch anyway.
Since the switches are prone to break down, it doesn't feel satisfying to replace it with a used switch that's likely to fail soon anyway. (Sorta like the MPS problem.)
The late Lapuwali suggested several times that a VW switch (@$40 OEM, $20 aftermarket) could be converted of 914. His reasoning was they functioned the same: 1 Off, 2, Non-keyed power to parking lights, etc., 3. Keyed power to headlights. His theory was that the Porsche switch internally ganged terminals while VW combined the wires before entering the switch and therefore VW switches had fewer connections. He proposed an adapter plate that spliced the proper terminals that could then be connected to the VW Switch. I couldn't find a thread where that had been accomplished
The other school of thought is to relay the headlight part of a functioning light switch, prolonging its life. This suggestion confuses me because my reading of the diagram is that the "combination relay" already does this. For instance, current for the headlights seems to be supplied from 56 on the relay via closing 56 on the ignition switch. In other words, the HL switch does not carry the headlight current. So why another relay?
Am I mistaken? Anyone done either modification? How?
AM
My suggestion is to use a "known good" used one.
There are two ...
Early is 10 pin
Later is 11 pin
Which do you need?
Adding relays lessens the current through a switch. Old wiring also increases resistance and commensurately heat.
Since the switch has probably lasted 40 years, who knows how many cycles it has seen.
I am not one who works out the diagrams to add relays or use different switches. When I am forced to, I will do it, but for now I stick with used switches.
I don't think I have any 10 pin switches, but will at least look.
I can use either, so they say (jump the extra terminal to keyed power? Or something like that.) Thanks.
Hi, EBay has some listed even as I speak. Some early style some late. I've had good sucess with the ones I've purchased in the past. If your handy and not in a hurry. Pelican has a good article on rebuilding the little buggers. I'm not all that handy and I managed to follow the directions correctly. I wouldn't recomend changing the wireing.
Here's all you wanted to know about the guts of the early switch:
http://members.rennlist.com/pbanders/headlight_switch_internals.htm
--DD
The headlight current does go through the high/low relay, but it goes through the headlight switch to get there. So it would probably be worthwhile to use a relay to reduce the current going through that part of the switch.
There's no relay in the engine bay light/instrument lights/license plate lights/etc. circuit. The instrument lights one comes out of the switch, through fuse 7, then back into it again to go through the dimmer (rheostat), and back out again to the lights. You could put a relay in before or after fuse 7 to offload that circuit.
The power to the headlight motors does not go through the switch, the switch triggers the relays that run the motors.
Power for the parking lights, under some circumstances, does go though the switch. There's no relay, but there are fuses, numbers 5 and 6.
I hope the above is of some use. The information in it comes from the 74 wiring diagram; the circuitry for the earlier cars is slightly different.
--DD
Thanks Dave, that does help. Ironically, the Pelican Tech page that also has Brad Anders switch disassembly article contains a follow up about late model switches. Apparently they separate the contacts for the head light illumination and head light motors: 56 and 56K.
Stuart,
http://www.google.com/url?sa=t&rct=j&q=rally%20lights&source=web&cd=1&ved=0CGcQFjAA&url=http%3A%2F%2Fwww.rallylights.com%2F&ei=V4OFT_rTIbLUiAL-h_H1BA&usg=AFQjCNGG9j7bwyscvFqY_sNLJ2R6peUaZQ
You can buy relay kits here and I think they have some electrical diagrams also explaining how to install. You will need to run heavy wire from the battery to the relays. I have seen discussions on here about installing relays for the high output headlights. One of the reasons some opted for the 6-way fuse block versus the 4-way. You may be able to find info at Bus Depot also.
Your turn signal stalk "toggles" the hi/low relay.
Tom
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)