Printable Version of Topic

Posted by: jeff88ix Aug 4 2013, 07:55 PM

Anyone have a template for the pedal board? I don't have the original and would like to make one. AutoCad, .dxf, or ? pretty sure I can use most file formats.

Thanks
Jeff

Posted by: ConeDodger Aug 4 2013, 07:58 PM

I think 914Rubber sells them... Peddle boards I mean...

Posted by: stugray Aug 4 2013, 08:03 PM

wondering if I could scan one......

I have a pristine blank.

Stu

Posted by: chad newton Aug 4 2013, 08:07 PM

Like a dumb a$$ I threw mine away. I probably won't install one now.

Posted by: stugray Aug 4 2013, 08:19 PM

My scans didn't look too good. out of focus & cant get the whole thing.
how about Hires photos?
Can you convert them?

If you could make two nice reproductions from a superior material, I would send you my perfect board as a master.

Stu

Posted by: jeff88ix Aug 4 2013, 08:24 PM

Stu,

I was just planning on making a wood one, I think I just need a good tracing, something full scale. I could then make an AutoCad file that would be available to others.

Thanks
Jeff

Posted by: speed metal army Aug 4 2013, 10:21 PM

914 rubber has em.

Posted by: Mark Henry Aug 5 2013, 08:05 AM

I wouldn't do that as the board has a stop that limits the clutch (IIRC) return travel. I can't remember the details, but I remember not using one causes stress on a component that can lead to a failure.

Posted by: lsintampa Aug 5 2013, 08:16 AM

Yeah, what happens is the cable (if not stopped) can be stretched and over time will brake. Same can happen with the throttle cable if you have it stretching at full throttle.

Posted by: Cap'n Krusty Aug 5 2013, 08:17 AM

Thet component would be the clutch cover, AKA pressure plate.

The Cap'n

Posted by: Bartlett 914 Aug 5 2013, 10:19 AM

Throttle stop is also important. You can damage the throttle body, break the cable or have it pull out of the clamp.

Posted by: Mikey914 Aug 6 2013, 06:44 PM

Got them if you want. I even put it on sale for you if you need it.
http://shop.914rubber.com/Plywood-floor-board-drivers-side-only-914FB-P.htm

Posted by: solex Aug 7 2013, 01:29 PM

I cut mine out of aluminum covered plywood the same thickness as the original except much stronger

Posted by: Mikey914 Aug 9 2013, 08:53 AM

Why not just cut it out of aluminum?

Posted by: LotusJoe Aug 9 2013, 10:01 AM

Like this one. I had it cut at my local hydro-cutter

Posted by: jimkelly Aug 9 2013, 10:06 AM

just buy it

http://shop.914rubber.com/Plywood-floor-board-drivers-side-only-914FB-P.htm;jsessionid=45E8362F0D384BC23923E1FD055A33E1.m1plqscsfapp04

Posted by: 7TPorsh Aug 9 2013, 10:20 AM

oooh...can I get on of these?

Posted by: LotusJoe Aug 9 2013, 11:12 AM

Sold all of my last batch. I might consider another run here soon.

Posted by: Wegeng_Haus Aug 9 2013, 12:01 PM

have the template for the passenger side floorboard, that I designed.



Attached thumbnail(s)

Posted by: solex Aug 9 2013, 01:53 PM

That's what I had lying around

Posted by: jeff88ix Aug 9 2013, 04:26 PM

Ok, I have found an original to copy, Thanks Van!

I plan on making an AutoCAD drawing of it which I will make available to others when done.

Thanks everyone!
Jeff