So, I installed a "rebuilt" set of 320i calipers that bought on evilbay. They had already been machined to take care of the clearance. Bolted them right up, went to bleed the system... and all of a sudden I find out that the pads are not squeezing together. There's fluid coming into the caliper, since I can bleed them... but the brake pedal is not getting any harder... and I'm not seeing that the pads are getting anywhere.
I'm guessing the calipers might have one of two problems. Either lack of lubrication from sitting around for a few weeks, or paint has dried on them (they were painted when I bought them).
Anybody got a suggestion to make 'em squeeze? Am I SOL with these?
Thanks,
Carlos
Take'em off.
Pop them open.
See what's wrong.
They are very straight forward to work on.
Don't take chances with an "on car" fiix.
you have a new MC right? new calipers and a new MC take forever to bleed!
i replaced to calipers and it took me 6gts of brake fluid to chase all the bubbles out. try tapping on the MC and the calipers with a rubber mallet. chase some airbubbles out...
pedal will NOT get hard until all bubbles are gone....
Keep bleeding...youll get it!
I didn't install a new MC (I decided to let a shop do this). So, I was hopnig to get enough fluid pressure to get the car to the shop, but I haven't been able to get them to move.
Would air in the line prevent the pads from moving AT ALL?
I mean, they are not moving... as if the caliper was frozen.
hmmm.... depends on how much air you got going on......
keep bleeding and report back
how long have you been bleeding? lots of bubbles come out?
A little air in the line shouldn't prevent them from moving. The difference is air compresses, fluid does not. Sounds like you have a "lot" of air somewhere compressing hence, making your pedal "not get any harder" and your pistons not move.
Also, no amount of paint should stop a piston from moving if it wants to. Rust or corrosion inside the cylinder is another story. They may have rusted while sitting.
If'n it was me? I'd bleed and bleed again. Go with A-a-ron's advice. (cause your pedal isn't getting any harder.) Have a partner and have them "SLAM" the brakes. Now... if after you beeld them again and you get a firm pedal and you still can't get those pistons to move then yank them like Marty recommends.
Soft pedal = air, not frozen pistons, especially if you're getting clean fluid up there.
Do gravity bleed: take a section of clear tubing, attach it to the bleeder screw, dangle it over the fender and into the open trunk. Put the end in a bottle if you're paranoid. Remove the cap from the reservior. Fill the reservoir completely. Open the bleeder. Put a board or brick or something on the brake pedal to hold it to the floor. Wait for awhile. If you watch, you'll see fluid rise slowly in the tube. After a bit, you should see some bubbles in the tube. You may also see bubbles in the MC reservoir. The fluid in the tube will stop rising once it reaches the level in the reservoir. Add fluid as necessary. Close the bleeder and repeat on the other caliper.
It would be best to do this AFTER you replace the MC. Replacing this really isn't that hard, it's just a knuckle buster.
If the gravity bleed method doesn't get you some brakes, with at least a medium pedal (not firm, not squishy), then there's something wrong with the calipers or the MC. The calipers may be frozen.
I'd say I've bled through about 1/4 of the "large" bottle... roughly 2-3 refills of the reservoir so far. but I should have had SOME pressure already building up, don't you think?
Are the Bleeders oriented to the top of the Caliper ???
Start at the passenger rear tire, the farest point from the master cylinder, have some body pump the pedal 6,7,8 times hold it, open the bleeder then close the bleeder, repeat this procedure untill you start getting some fluid, move to driver side rear tire, repeat prcedure, move to passenger front tire, repeat procedure, next driver side. Repeat intire procedure, the pasenger side rear, driver side rear, passenger side front, drivers side front, untill no more air bubbles. Some brake systems decide they don't want to be bled. are you going to let this brake system win?
And if that doesn't work, you could allways beat it till it bleeds
Richard
Do you still have the proportioning valve installed in the engine bay? If it is, there is your problem. You need to scrap it and get a "T" fitting.
Had a similar problem with mine when I first got it and was trying to get it road-worthy. I bled the system like 4 times and it never got any better. Finally found that one of the main seals inside of the MC had let go. This was in a NOS ATE MC that I had just installed. So my question is, did you ever have good brakes after your MC was replaced? Or did the problem just start when you swapped calipers?
(Eric answering for Carlos) He hasn't replaced the MC yet.
What's the weather like up there? We had nearly 60 down here yesterday. December 10th driving day!
Weather here was great the other day. Went pheasant hunting in a tee shirt. Looking forward to driving the teener all winter although it has been a bit ranier than usual for the past couple weeks. BTW, where is Sandy?
carlos,
try bleeding right rear first, the left rear, then right front, then left front. Bleed each caliper until thry have no bubbles... you will go through MORE than 2 qts....
to bad you didnt make the fun run today, next time
You can also potentially blow out the seals in your MC if it's tired and if you really vent some anger on it while attempting to bleed. I did this to my '78 F-150 (rusty parts hauler) recently and wound up messing up the MC to the point that no fluid was getting to the rear circuit, thus making it seem like I wasn't making any progress on the bleeding process. I used full but gentle compression of the brake pedal to bleed after installing the new MC and that worked fine.
Just another thought for consideration. I do agree with previous posts that air can be maddening to get out of the system after replacing calipers. I'm currently battling that on my '76 BMW 2002.
Tim
Welcome Tim!
Well, I decided to take a day off and went off with my pals to play paintball on Sunday instead.
Getting back to the questions and task at hand, I think I'm getting some air from the left rear hose, as this was the one that was leaking.. and the one I couldn't get out. So it doesn't surprise me that I'm getting so much air there. This could still be the main reason I couldn't get the front pads to squeeze... but I think I'm going to take my time on this one.
So... I think the order of business is... take out the old (17mm) MC and replace it with a 19mm as planned. After swapping out the MC, I will probably just have the car towed to the shop and ask them to relpace the rear hoses, bleed the brakes and be ready to go. So... new questions to follow on a new post.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)