Printable Version of Topic

Posted by: rnellums Nov 4 2013, 10:33 PM

Alright everyone! Ray and I are finally happy with the design quality and are planning to begin printing units Tuesday! This thread is going to be the official order thread, and orders will be filled as quickly as possible in the order of posts up here. Payment is preferred through Paypal (I’ll give the email for paypal out in a PM confirming your order) when it is ready to be shipped, but mailed check is also acceptable. Please, no payments until the item is packed and ready to be shipped.
There will be four models available, each priced at $45 shipped. Each model can hold a 32 oz “Big Gulp” comfortably, and excel equally well at holding more traditional 16oz coffee cups. The units will be printed in black ABS plastic, assembled using ABS glue. Each of these designs takes approximately 9 hours to print, allowing us to print two units per day. With the amount of interest in this item some will likely be waiting 30 days+ before delivery. The models are described below:

#1 The 914 Ashtray Cupholder - $45
This model has a printed front face and is intended as a direct slide-in replacement for the stock ashtray.







#4 The Stealth Ashtray Cupholder (Up to 73') -$45
This model re-uses the stock front from the ashtray, making the cupholder indistinguishable from a stock ashtray when closed.
There are differences between ashtrays! See http://www.914world.com/bbs2/index.php?showtopic=81276&hl=ashtray for more information. I expect that prior to mid-74 the ashtray fronts was held on with screws (100% compatible with stealth design), and after 74 they switched.

74 and LATER ASHTRAY CUPHOLDERS are now available!!

IMPORTANT: before placing your order, verify which ashtray you have (either a screw on ashtray front, or one with funny rivets).





There will also be several accessories available. The list of accessories, along with short descriptions of each are listed below.

#5 Soda-holding Insert -$8
This clips into the ashtray cupholder allowing it to hold a soda can or small water bottle



#6 Phone Holder -$15
This accessory clips into any of the ashtray cupholders and rotates to lock in place. I currently have holders for the following phones, but will be continuing to expand the models available.

• a. Galaxy S4
• b. Nokia Lumia 920
• c. Iphone 4
• d. Iphone 5

Posted by: ben*james Nov 4 2013, 10:49 PM

I will take the 914 ashtray cup holder!

Will take a phone adapter when you get one for the Samsung note 3.

Thanks, I'm pumped!

Posted by: billh1963 Nov 5 2013, 05:49 AM

Put me down for a number one ashtray holder, please

Posted by: naro914 Nov 5 2013, 06:45 AM

I will take a #4 holder, soda holder and iphone 5 holder (I assume 5 and 5s are the same??)

Posted by: Racer Chris Nov 5 2013, 07:38 AM

I'll take one of the #1 cupholder
and one of the #4 cupholder please.

Posted by: jfort Nov 5 2013, 08:13 AM

I would like the iPhone holder

Posted by: warrenoliver Nov 5 2013, 08:39 AM

Any pics of #2 and #3?

Warrenoliver

Posted by: JRust Nov 5 2013, 08:59 AM

I'll take a #1 with the pop can holder option & the Samsung s4 mount. My question is will it accommodate the case on the phone? Or will I have to remove the case to use the current setup?

Posted by: rnellums Nov 5 2013, 09:00 AM

QUOTE(jfort @ Nov 5 2013, 10:13 AM)

Posted by: rnellums Nov 5 2013, 09:00 AM

QUOTE(warrenoliver @ Nov 5 2013, 10:39 AM)

QUOTE(JRust @ Nov 5 2013, 10:59 AM)

Posted by: hcdmueller Nov 5 2013, 09:34 AM

I will take a #1 with soda can holder. Is it bad that I don't have a phone, much less a smart phone?

Posted by: wndsnd Nov 5 2013, 09:51 AM

I'm in for a basic #1

Posted by: Jeffs9146 Nov 5 2013, 10:06 AM

PM sent

I am in for

1-#1
1-#5

Posted by: boxsterfan Nov 5 2013, 11:57 AM

Awesome. The cupholder problem has been solved.

Posted by: poorsche914 Nov 5 2013, 12:11 PM

Has this been road tested? Seems the can would go flying first time you take off or take a turn

Otherwise, awesome product, Ross.

Posted by: 7TPorsh Nov 5 2013, 12:19 PM

A video of one of these being printed would be fascinating,

Posted by: x-faktory Nov 5 2013, 12:45 PM

I'll take a #4 stealth version

Posted by: Steve Nov 5 2013, 12:49 PM

I will take the following:
#4 Stealth.. I have a screw on front ash tray
#5 Can adapter
#6 d for an iPhone 5

thanks!!!

Posted by: Philip W. Nov 5 2013, 01:46 PM

I'm in for a #4 for my '75(not sure of type, i will check tonight)/
and - phone holder- droid razr maxx- dimensions posted on other thread)
and - water bottle thingy.

Posted by: Zimms Nov 5 2013, 02:07 PM

I am in for a #4

Posted by: rnellums Nov 5 2013, 02:12 PM

QUOTE(poorsche914 @ Nov 5 2013, 02:11 PM)

Has this been road tested? Seems the can would go flying first time you take off or take a turn

Otherwise, awesome product, Ross.

Posted by: JRust Nov 5 2013, 02:23 PM

QUOTE(rnellums @ Nov 5 2013, 08:00 AM)

QUOTE(JRust @ Nov 5 2013, 10:59 AM)

I'll take a #1 with the pop can holder option & the Samsung s4 mount. My question is will it accommodate the case on the phone? Or will I have to remove the case to use the current setup?

The mount is designed for a phone without the case, so a phone-in-case will likely not fit. If you want a custom size, i can make one using dimensions you send me after the main ashtray cupholder production run is done, but I can't verify the fit will be perfect(there is a lot of tweaking involved to get the fit right).

Posted by: peteyd Nov 5 2013, 02:33 PM

Hello,

Put me down for a #4 and a #6 for the iphone5

thanks,

Peter

Posted by: poorsche914 Nov 5 2013, 04:57 PM

QUOTE(rnellums @ Nov 5 2013, 03:12 PM)

Posted by: zambezi Nov 5 2013, 09:43 PM

Put me down for the #2 embossed holder with a #5 soda can insert.

Posted by: Kaduku Nov 5 2013, 10:04 PM

#4 please!

Posted by: eric9144 Nov 6 2013, 11:47 AM

#1, soda insert and iPhone insert

Posted by: damesandhotrods Nov 6 2013, 12:33 PM

She who must be obeyed would like a #2 embossed and a #5 soda insert…

Posted by: CptTripps Nov 6 2013, 01:54 PM

I've got a '75, so let me know when you have them ready.

Posted by: rnellums Nov 6 2013, 03:20 PM

QUOTE(eric9144 @ Nov 6 2013, 01:47 PM)

#1, soda insert and iPhone insert

QUOTE(CptTripps @ Nov 6 2013, 03:54 PM)

Posted by: jfort Nov 6 2013, 04:29 PM

QUOTE(rnellums @ Nov 5 2013, 07:00 AM)

QUOTE(jfort @ Nov 5 2013, 10:13 AM)

I would like the iPhone holder

The phone mount clips into the ashtray cupholder. Is there a specific model you would prefer (#1 or #4)?

Posted by: eric9144 Nov 6 2013, 05:20 PM

QUOTE(rnellums @ Nov 6 2013, 02:20 PM)

Posted by: Java2570 Nov 6 2013, 05:40 PM

Put me down for #4 stealth....these look great, Ross!!

Posted by: rnellums Nov 6 2013, 10:04 PM

Check out this cross section of one of your printed parts! We are using a 10% infill to decrease weight and print time(although still at 9 hours each!), while maintaining strength!

-Ross

Posted by: David Stowers Nov 7 2013, 09:17 AM

Hi,
I'd like a #1 and a#5 please plus shipping to the UK

Posted by: GulleyGulley Nov 7 2013, 09:22 AM

I will take a "stealth" holder, iPhone 5 holder & water bottle holder

QUOTE(rnellums @ Nov 4 2013, 11:33 PM)

Alright everyone! Ray and I are finally happy with the design quality and are planning to begin printing units Tuesday! This thread is going to be the official order thread, and orders will be filled as quickly as possible in the order of posts up here. Payment is preferred through Paypal (I’ll give the email for paypal out in a PM confirming your order) when it is ready to be shipped, but mailed check is also acceptable. Please, no payments until the item is packed and ready to be shipped.
There will be four models available, each priced at $45 shipped. Each model can hold a 32 oz “Big Gulp” comfortably, and excel equally well at holding more traditional 16oz coffee cups. The units will be printed in black ABS plastic, assembled using ABS glue. Each of these designs takes approximately 9 hours to print, allowing us to print two units per day. With the amount of interest in this item some will likely be waiting 30 days+ before delivery. The models are described below:

#1 The 914 Ashtray Cupholder - $45
This model has a printed front face and is intended as a direct slide-in replacement for the stock ashtray.






#2 The Embossed 914 Ashtray Cupholder - $45 ***Coming Soon
This model is identical to the Ashtray Cupholder above, but front face has the 914 script embossed on it.


*more photos to come soon


#3 The Engraved 914 Ashtray Cupholder -$45 ***Coming Soon
This model is identical to the Ashtray Cupholder, but the front face has the 914 script engraved on it.


*more photos to come soon


#4 The Stealth Ashtray Cupholder (Up to 73') -$45
This model re-uses the stock front from the ashtray, making the cupholder indistinguishable from a stock ashtray when closed.
There are differences between ashtrays! See http://www.914world.com/bbs2/index.php?showtopic=81276&hl=ashtray for more information. I expect that prior to mid-74 the ashtray fronts was held on with screws (100% compatible with stealth design), and after 74 they switched.

Later ashtrays are not compatible with an early style mount. I am in the process of designing a compatible mount for 74 and later ashtrays, and hope to have it available soon.


IMPORTANT: before placing your order, verify that you have either a screw on ashtray front, have access to an ashtray with a screw on front.





There will also be several accessories available. The list of accessories, along with short descriptions of each are listed below.

#5 Soda-holding Insert -$8
This clips into the ashtray cupholder allowing it to hold a soda can or small water bottle



#6 Phone Holder -$15
This accessory clips into any of the ashtray cupholders and rotates to lock in place. I currently have holders for the following phones, but will be continuing to expand the models available.

• a. Galaxy S4
• b. Nokia Lumia 920
• c. Iphone 4
• d. Iphone 5

An anticipated accessory eventually is an adjustable holder, but no design work has been completed on it at this point.

In summary, the prices are as follows:
Any 914 ashtray cupholder - $45
Soda Holder -$8
Phone Mount - $15

Below are some videos of the ashtray in action. These represent the worst case of use for most users, as the test vehicle is a 2.4L typeIV, with the Koni suspension set to full stiff on bumpy roads! I did not go easy on it!

Cup Holder:
http://youtu.be/J3oRbCKoqnk

Phone Mount:
http://youtu.be/lG-zEAxf9WE


Thanks for looking ! Please PM me for any questions, as I would like to keep this thread strictly for orders!


Current Confirmed Orders *-Local Pickup
Ben*James - #1 914 Ashtray Cupholder, Samsung Note 3
Billh1963 - #1 914 Ashtray Cupholder
Kansas914* - #4 Stealth Ashtray Cupholder, Samsung Galaxy Note
MojoRisen* - 2 x #4 Stealth Ashtray Cupholder (74+)
Naro914 - #4 Stealth Ashtray Cupholder, Iphone 5, Soda
Racer_Chris - #1 Ashtray Cupholder, #4 Stealth Ashtray Cupholder
1stWorks* - ?, Galaxy Note 2, Soda
Jfort - #4 Stealth, Iphone 5
JRust - #1 914 Ashtray Cupholder, Galaxy S4, Soda
hcdmueller - #1 914 AShtray Cupholder, Soda
wndsnd - #1 914 Ashtray Cupholder
jeffs9146 - #1 914 Ashtray Cupholder, Soda
x-faktory - #4 Stealth
Steve - #4 Stealth, Iphone 5, Soda
Phillip W. - #4 Stealth (74+), Droid Razr Maxx, Soda
Zimms - #4 Stealth
peteyd - #4 Stealth, Iphone 5
Zambezi - #2 Embossed, Soda
914itis - #1 914 Ashtray Cupholder,Iphone 5, Soda
Kaduku - #4 Stealth
eric9144 - #1 914 Ashtray Cupholder, Iphone 4, Soda
DamesandHotrods - #2 Embossed, Soda
Ellisor3 - #1 914 Ashtray Cupholder, Soda
Java2570 - #4 Stealth
914four - #2 Embossed, Iphone 4



Current Tentative Order List

Pthompson509
Dave_Darling
David Stowers
Mstein95
PittsM12
Orthobiz
skeates
siverson
doorknobcollector
porbmw
warrenoliver
Turk22
flipb
timothy_nd28
no1uno
ConeDodger
mepstein
tornik550
cpttripps
gudhjem
gulleygulley
nolift914 (x2)
r_towle
Harpo
Scotty B
mrhyde
Michael7810
barefoot

Posted by: larryM Nov 7 2013, 03:03 PM

I will buy both a #1 and a #4

please send paypal invoice

Larrym

Posted by: krk Nov 8 2013, 09:41 PM

I love this project. (and, oh, I love 3D printing....)

I'm in for #1, #4 and #6. (I have a droid x -- hopefully it'll work, but I'll work with
what I get

PMO works best for me. PM me where to send it

--krk.

---
Kim Knuttila
mobile: 408 564 9545

Posted by: rnellums Nov 9 2013, 12:26 AM

QUOTE(krk @ Nov 8 2013, 11:41 PM)

I love this project. (and, oh, I love 3D printing....)

I'm in for #1, #4 and #6. (I have a droid x -- hopefully it'll work, but I'll work with
what I get

PMO works best for me. PM me where to send it

--krk.

---
Kim Knuttila
mobile: 408 564 9545

Posted by: Harpo Nov 9 2013, 08:17 AM

I would like #3 engraved & #6d iPhone 5


Edited

Change mine to #1 (late) and iphone 5 adapter
Thanks

David

Posted by: MrHyde Nov 10 2013, 05:16 PM

I'll go for 4 , 5, 6d for iPhone 5
Thanks for all the work !

Posted by: auto_cran Nov 10 2013, 08:01 PM

Please put me down for

#2 Embossed, Soda


Like others -thanks for doing this!

Chris
(auto_cran)

Posted by: rnellums Nov 14 2013, 06:46 PM

The first 6 are shipping out!

Ray and I are going to wait until we hear back from the first six customers on how they like the quality before heading into production full swing. It is my hope that these first buyers will post their honest opinions of the product in this thread to provide a customer's perspective on the cupholders.

It is very important to us that people are happy with the product, so I want to be very clear about the level of finish of the 3d-printed parts.

Due to the way the printers work, the top of each part looks like a topographic map, and the build layers are visible. This is a 3d-printed part and looks as such.

Ray and I feel that the resolution/finish of the printer leaves something to be desired(is not that of a production part). That said, for us, the usefulness of the design far outweighs the aesthetic compromises.

I couldn't be more happy with how it works in both my 914's.

-Ross

Posted by: scotty b Nov 14 2013, 06:53 PM

put me down for

#4 = stealth
#5 = can holder

Thanks

Posted by: turk22 Nov 15 2013, 09:06 PM

Ross,

I'm sorry, I didn't firm up my order earlier.

I'll take the stealth model.

Turk

Posted by: rmdinmd Nov 17 2013, 08:20 PM

put me down for a
#2 holder and
soda holder.


great idea.

Rick

Posted by: David Stowers Nov 21 2013, 10:39 AM

How's production going? Any feedback from the first batch yet?

Posted by: naro914 Nov 21 2013, 11:07 AM

I got mine on Monday and really like it, though I have not really 'tested' it while driving. I am not bothered at all about the 3D build layers because I got one of the 'stealth' versions so the only time you would see the surface of the part is when its pulled out...and to be honest it looks MUCH better than the old finish of my ash tray anyway!!

To me, the usefulness, quality and value FAR exceed any concerns one would have on the look and feel, which honestly is not bad at all anyway.

Here would be my only comment...you need a fairly large mug/cup to fit in without sliding through. No wimpy 'small' size Starbucks...though I think a pint glass fits nicely...

(Gosh, look at those cracks in the dash!!)

Posted by: Kansas 914 Nov 21 2013, 07:48 PM

QUOTE(David Stowers @ Nov 21 2013, 09:39 AM)

Posted by: ben*james Nov 21 2013, 09:54 PM

I love it!

It's not so close to OEM looking that you would mistake it for being factory but it is tastefully done and seems to function very well.

My vote for best new 914 product of the year.

(My balls thank you. No more scolding coffee burns)

Posted by: rnellums Nov 23 2013, 08:17 PM

Ray and I are rolling into production! Several more will be headed out monday!

I have attached a couple of images of how the locking lugs work. You use an allen wrench to turn the lug from the 3 o'clock to 7-8 o'clock (straight down on stealth models will hit the heater controls behind the dash).

With regard to the stealth models, I want to make sure everyone knows that they do not come with a front. You will need to re-use the stock ashtray front portion.

I'm looking forward to getting more feedback!

-Ross


Attached image(s)

Posted by: scotty b Nov 23 2013, 08:25 PM

Ross, I may have missed this, but when and how do you want payment ?

Posted by: rnellums Nov 23 2013, 08:31 PM

QUOTE(scotty b @ Nov 23 2013, 10:25 PM)

Posted by: billh1963 Nov 27 2013, 06:53 AM

I'm late to post a review but I'm very please with mine! The fit is good and it fills the ashtray hole nicely. I won't bother posting a picture since others have done that already.

I don't drink coffee so I can't comment on the fit of a coffee cup. However, it does hold a water bottle with a little persuasion

The only issue would be the texture on the front,,, that will be a matter of personal taste.

Overall it's a great product and I'm sure improvements will be coming at a rapid rate over the next few months!

Posted by: rnellums Nov 27 2013, 09:13 AM

A bit of bad news. Looks like the controller board on the printer bit the dust last night . We are on the horn with customer support trying to get this issue resolved, but it might take a while. I apologize for the delay everyone!

Posted by: Kansas 914 Nov 27 2013, 01:38 PM

QUOTE(rnellums @ Nov 27 2013, 08:13 AM)

A bit of bad news. Looks like the controller board on the printer bit the dust last night . We are on the horn with customer support trying to get this issue resolved, but it might take a while. I apologize for the delay everyone!

Posted by: wndsnd Nov 27 2013, 03:33 PM

I got my #1 Basic Cupholder today. Just in time for my road trip to Tangerine on Friday!

I have never seen a printed part before so I was really impressed. The engineering is great, the fit, perfect, and the little allen stop couldn't be easier.

I think I might like a stealth version, but the front of my ashtray to transfer isn't that great so I think this is the better version for me now.

Thank you.

Posted by: naro914 Nov 27 2013, 10:46 PM

I got my Soda Can and Iphone 5 holders today... all I can say is Wow... Everything fits very nicely, very snug and is very solidly built. Very, very impressive!! The Soda Can accessory works great for small coffee/water bottle/other small drinking objects....a must have IMO

They have done an awesome job with all this.... my 911 buddies are jealous!!

Posted by: krk Nov 27 2013, 11:20 PM

QUOTE(rnellums @ Nov 8 2013, 10:26 PM)

QUOTE(krk @ Nov 8 2013, 11:41 PM)

I love this project. (and, oh, I love 3D printing....)

I'm in for #1, #4 and #6. (I have a droid x -- hopefully it'll work, but I'll work with
what I get

PMO works best for me. PM me where to send it

--krk.

---
Kim Knuttila
mobile: 408 564 9545

I can definitely design something up that should work, but I'll need good measurements. Do you have a set of calipers? PM me for further discussion!

Posted by: rnellums Dec 1 2013, 10:28 AM

Great news! Ray has fixed the printer (two wires had broken from fatigue) and we are back up and printing!

-Ross

Posted by: David Stowers Dec 5 2013, 06:09 AM

Great news! Keep pumping them out guys

Posted by: David Stowers Dec 11 2013, 03:03 AM

Where are we with the production list? Can't wait for mine!

Posted by: rnellums Dec 11 2013, 08:54 AM

David,

I updated the list. We are currently cranking out around 6 orders a week. We have also been working on some cool upgrades that we should be rolling out pretty soon!

Sorry it is taking so long!


-Ross

Posted by: porbmw Dec 11 2013, 01:31 PM

Forgot about this.

Can you put me down for a Stealth, with soda insert.

Thanks

Paul

Posted by: rnellums Dec 11 2013, 01:44 PM

QUOTE(porbmw @ Dec 11 2013, 12:31 PM)

Posted by: jfort Dec 11 2013, 02:23 PM

got mine the other day. stealth unit with iPhone 5S holder. Haven't put it in the care yet. Need to install the real front onto the unit. The iPhone fits perfectly. So far, so good.

Posted by: David Stowers Dec 11 2013, 04:18 PM

QUOTE(rnellums @ Dec 11 2013, 06:54 AM)

Posted by: melly Dec 12 2013, 03:26 PM

Hi, I'd like to order a stealth unit and an iphone insert.

Patrick Melly

Posted by: wndsnd Dec 12 2013, 03:50 PM

I would like to order

1) can insert for holder already purchased
1) phone insert if it works with Galaxy S3

Thanks

Posted by: J0n52 914 Dec 12 2013, 09:13 PM

#1 cup cupholder please.



Thanks

Posted by: 914four Dec 13 2013, 03:44 AM

Please change my order, if it is not too late, to #2 Embossed, Galaxy S4 Active and Soda Holder.

Kelvin

Posted by: karlo Dec 13 2013, 06:25 AM

You should consider printing these with the Taulman 645 nylon filament. I've used that a lot lately, and I am really impressed. It's tougher than anything I've printed with before, abrasion resistant and flexible. Short of taking a box cutter or lighter to the printed parts, they really cannot be destroyed.

Posted by: rnellums Dec 13 2013, 08:45 AM

QUOTE(914four @ Dec 13 2013, 02:44 AM)

QUOTE(karlo @ Dec 13 2013, 05:25 AM)

Posted by: ConeDodger Dec 13 2013, 09:55 AM

Stealth + soda can holder + iPhone5 if i'm not already listed.

Posted by: CptTripps Dec 13 2013, 10:07 AM

Any idea when you'll have one available for a 1975?

Posted by: rnellums Dec 13 2013, 07:12 PM

QUOTE(ConeDodger @ Dec 13 2013, 08:55 AM)

Stealth + soda can holder + iPhone5 if i'm not already listed.

QUOTE(CptTripps @ Dec 13 2013, 09:07 AM)

Posted by: turk22 Dec 13 2013, 10:30 PM

QUOTE(turk22 @ Nov 15 2013, 10:06 PM)

Posted by: CptTripps Dec 14 2013, 04:05 AM

QUOTE(rnellums @ Dec 13 2013, 08:12 PM)

Posted by: StratPlayer Dec 14 2013, 09:18 PM

#4 for me please... late model

Posted by: RickS Dec 15 2013, 12:29 AM

#4 with Soda Insert. Thx

Posted by: Jeffs9146 Dec 19 2013, 07:18 PM

I received my cupholder yesterday and spent a few minutes installing it today! Although it looks good and I am sure it will function as advertised I wanted to put out an issue that I had when it was put in!

I first tried to slide it into the ashtray slot and it started to bind up. When I got it to go all the way in I tried to pull it back out and the back lip kept hooking on the top of the ashtray track frame! I took some sand paper and smoothed out the edges on the back of the holder. It worked pushing it back in and out a few times so I decided to put the stop down to keep it from sliding out beyond where it is supposed to go! I then pushed it back in and pulled it back out and it stuck half way again on the lip. I pulled hard and it wouldn't budge! I started wiggling it and pulling it and WAM it popped all the way out braking the stop off!

At first I was a bit miffed but I decided to make one out of metal and ground some more off the lips!

It turned out fine, and works great, but I wanted to let other people know that if it sticks you may need to grind a bit of the lip off the back edge like in this photo!

I do like the holder.....thanks


Attached thumbnail(s)

Posted by: RazorbackFan78 Dec 24 2013, 12:16 PM

Please put me down for a #2 with Soda Insert.
Thanks! -Matt

***EDIT: since 2&3 are discontinued I'll take a #1 for my 73'

Posted by: Speedmster Dec 29 2013, 06:43 AM

Please add me to the list. I would like a #4 The Stealth Ashtray Cupholder (Up to 73') -$45 and a #5 Soda-holding Insert -$8.

PM to follow.

Posted by: rnellums Dec 29 2013, 09:45 AM

Ray and I have been cranking these out like crazy over the holidays! Look for a flurry of shipments in the next few days! Also, be on the lookout for a new development coming around the new year!

-Ross

Posted by: David Stowers Jan 6 2014, 11:50 AM

How's the flurry of shipments progressing?

Posted by: Jerlle Jan 7 2014, 01:38 PM

QUOTE(rnellums @ Nov 8 2013, 10:26 PM)

QUOTE(krk @ Nov 8 2013, 11:41 PM)

I love this project. (and, oh, I love 3D printing....)

I'm in for #1, #4 and #6. (I have a droid x -- hopefully it'll work, but I'll work with
what I get

PMO works best for me. PM me where to send it

--krk.

---
Kim Knuttila
mobile: 408 564 9545

I can definitely design something up that should work, but I'll need good measurements. Do you have a set of calipers? PM me for further discussion!

Posted by: David Stowers Jan 15 2014, 05:02 AM

QUOTE(David Stowers @ Jan 6 2014, 09:50 AM)

How's the flurry of shipments progressing?

Posted by: rnellums Jan 15 2014, 08:48 AM

Yes! my apologies for not responding to you last message! I sent out 7 earlier this week! Specifically, David, your cup holder is on deck to be printed! Ray is out of town this week, but it should be about ready next week!

I made an Assembly and installation video, and then promptly lost the phone it was recorded on, but look for one of those coming in the near future!

Posted by: David Stowers Jan 15 2014, 09:03 AM

QUOTE(rnellums @ Jan 15 2014, 06:48 AM)

Posted by: Java2570 Jan 18 2014, 08:52 PM

Hey Ross - I got my stealth cupholder the other day, thanks for the quick shipment!
It fits the dash great and I'm pleased with it. The only issue I see so far is my latch is getting hung up on my wiring for the "fasten seat belt" light underneath. I was in a hurry to get off to work and it's freezing in my garage so it'll have to wait for another day. Thanks for making a cool product for us!! Jon

Posted by: Steve Jan 23 2014, 04:51 PM

I just got mine today and installed it. Nice product, very happy with it. Slid right in no problems. I just need to figure out how to reach back in there to turn down the latch, so it doesn't come out. The Soda Can insert is a must. Soda cans fits very nice as well as my small water bottles. I probably shouldn't have ordered the iPhone 5 adapter since my iPhone has an otter box case on it.

Posted by: rnellums Jan 23 2014, 04:56 PM

QUOTE(Steve @ Jan 23 2014, 03:51 PM)

Posted by: rnellums Jan 25 2014, 11:05 AM

Printing is going well, but unfortunately the #2 and #3 cup holders are not printing as well as could be hoped. Due to some difficulties in printing them we will be discontinuing those models.

-Ross

Posted by: 914itis Jan 25 2014, 12:04 PM

QUOTE(Steve @ Jan 23 2014, 05:51 PM)

Posted by: rnellums Jan 25 2014, 12:09 PM

QUOTE(914itis @ Jan 25 2014, 11:04 AM)

QUOTE(Steve @ Jan 23 2014, 05:51 PM)

I just got mine today and installed it. Nice product, very happy with it. Slid right in no problems. I just need to figure out how to reach back in there to turn down the latch, so it doesn't come out. The Soda Can insert is a must. Soda cans fits very nice as well as my small water bottles. I probably shouldn't have ordered the iPhone 5 adapter since my iPhone has an otter box case on it.

Got mine as well and I agree with the comments. However the iPhone adapter is useless and maybe to must of us. The issue with the iPhone is thickness,; one must remove the case To fit. I have the slimmest case and no go. Must of us have a case and it's inconvenient to remove.

Posted by: Speedmster Feb 8 2014, 11:04 AM

QUOTE(Speedmster @ Dec 29 2013, 07:43 AM)

Posted by: larryM Feb 8 2014, 05:35 PM

got mine about 2 weeks ago - nice idea, works well

got one of each normal & stealth -

- agree on the challenge of setting the tab -

did have to trim the left edge of the normal style unit to clear my dashtopper, but that's my problem, not the unit's - it can easily be shaped on a bench grinder

Posted by: David Stowers Feb 9 2014, 03:40 AM

QUOTE(larryM @ Feb 8 2014, 03:35 PM)

Posted by: rnellums Feb 9 2014, 10:01 AM

QUOTE(David Stowers @ Feb 9 2014, 02:40 AM)

QUOTE(larryM @ Feb 8 2014, 03:35 PM)

got mine about 2 weeks ago - nice idea, works well

got one of each normal & stealth -

- agree on the challenge of setting the tab -

did have to trim the left edge of the normal style unit to clear my dashtopper, but that's my problem, not the unit's - it can easily be shaped on a bench grinder

Not had mine yet. How come they're not being done in the order on page one anymore?

Posted by: MegoManSF Apr 8 2014, 03:00 PM

[size=2]
I would like the embossed one. I have a '74 with the rivet style ashtray. I'd also like the water bottle attachment and attachment for iPhone 5. If you want to send me a PayPal statement my email is copykatharry@comcast.net. Thank you so much for this ingenious invention! How long will it take to get? Thanks- Harry

Posted by: rnellums Apr 8 2014, 03:03 PM

I'm afraid we have halted production for the moment. Both Ray and I have gotten so busy at work that completing this side project has become a minor priority. I'm sure it will get back going again in the future, but there certainly isn't a delivery time frame for the moment.

-Ross

Posted by: MegoManSF Apr 8 2014, 04:17 PM

QUOTE(rnellums @ Apr 8 2014, 02:03 PM)

I'm afraid we have halted production for the moment. Both Ray and I have gotten so busy at work that completing this side project has become a minor priority. I'm sure it will get back going again in the future, but there certainly isn't a delivery time frame for the moment.

-Ross

Posted by: 75porsche914 Jul 4 2014, 08:16 PM

If these are still being produced, can I please purchase an all black one, closest to OEM looking for a cup holder/water blt holder please?

If needed I have a couple extra ash-trays.

Don't think it matters but my car is a 75.

Thank you

Posted by: dudzy's914 Jul 4 2014, 08:33 PM

When will you make the regular ash tray with the embossed "914"?

Posted by: rnellums Jul 6 2014, 09:28 AM

QUOTE(75porsche914 @ Jul 4 2014, 08:16 PM)

If these are still being produced, can I please purchase an all black one, closest to OEM looking for a cup holder/water blt holder please?

If needed I have a couple extra ash-trays.

Don't think it matters but my car is a 75.

Thank you

QUOTE(dudzy's914 @ Jul 4 2014, 08:33 PM)

Posted by: 76-914 Jul 7 2014, 07:56 AM

Making one for the Suby converts, too?

Posted by: 914socal Sep 13 2014, 07:45 PM

Will you guys start production on these ashtrays again?

Posted by: Hank914 Sep 13 2014, 07:55 PM

QUOTE(914socal @ Sep 13 2014, 06:45 PM)

Posted by: rnellums May 4 2015, 11:04 PM

Well I'm afraid to say the printed cupholders don't look like they'll be coming back, but I think I have arrived at a viable replacement.

Introducing the next ashtray cupholder - out of stainless!




Model 1:
Uses the stock ashtray front from a 73 or earlier ashtray, looks totally stock when it's pushed into the dash.

In order to get enough throw to fit a cup, the rails on the ashtray mount in the dash must be modified (filed) to be shorter. Does not effect the ability to go back to a stock ashtray in the future.

Model 2:
No modifications to anything. Remove your ashtray and slide in the cupholder, I think it looks better with the face painted black and the background silver personally.


I'm looking for 4-5 people to trial test a few models at a discounted price before I go into full production.

Posted by: rnellums May 4 2015, 11:09 PM

In the dash.

Posted by: bandjoey May 4 2015, 11:53 PM

Hi Ross. I'm interested in a 914 version. What's the volunteer experimental highly discounted price? Bill.
Can u post a picture with a cup to see how big a drink cup fits? Thanks

Posted by: Hank914 May 5 2015, 01:09 AM

I'm interested in the 914 version also. Thanks!

Posted by: MJHanna May 5 2015, 07:13 AM

I'll be a guinea pig, I have a 74, I like the model 2 if it matters.

Mark

Posted by: Amenson May 5 2015, 07:20 AM

Put me down as a tester also, stock version....or the other whichever is needed more.

Posted by: sb914 May 5 2015, 07:22 AM

I'm in as well,stock look

Posted by: rnellums May 5 2015, 07:29 AM

Excellent! The beta group is closed. I'll send a few pms later today!

Posted by: 914ltd May 5 2015, 07:41 AM

Wow, I like it. I'll take 2 that use the stock front. Either style since I have lots of ash trays. Brad

Posted by: LeftCoastErik May 5 2015, 03:35 PM

I am in for a stock faced one also. Let me know when they are available! Thanks!

Posted by: A&P Mech May 5 2015, 07:22 PM

I had the opportunity to see both of the new stainless steel cup holders today. They are very cool. They are a vast improvement over the plastic version. I will be adding one to my car as soon as they become available.

Thanks Ross for working on this!

Ray

Posted by: bakerj May 5 2015, 07:25 PM

I wpold love to have one with the plain front.

Posted by: cary May 7 2015, 08:20 AM

Cool ................

Posted by: Harpo May 7 2015, 09:37 AM

Please sign me up for stainless version #2

Thanks

David

Posted by: brant May 7 2015, 10:55 AM

Ross,

put me down for a stock style when they become available.
and let us know what/where to file....

thank you sir
brant

Posted by: Kansas 914 May 7 2015, 11:01 AM

Hi Ross,

Nice job!

I too am in for a stock style - cheers!

Posted by: db9146 May 8 2015, 02:28 PM

Ooohh, stainless stock....I'm in!!!

Posted by: porbmw May 9 2015, 11:21 AM

Can you put me down for 2 of version 1....and PM me when you are ready to roll, re payment, etc
Thanks
Paul

Posted by: cdn914 May 9 2015, 01:34 PM

I will take one as well.

Gord

Posted by: StratPlayer May 9 2015, 03:24 PM

I'm in

Posted by: euro911 May 21 2015, 01:20 PM

Nifty item. How much are the 'New & Improved' stainless steel ones gonna cost?

Curious - why aren't you making the plastic ones any more?

Posted by: john77 May 21 2015, 06:06 PM

I'm in for a stock fronted one when they're available. Thanks.

Posted by: forrestkhaag May 21 2015, 07:41 PM

off topic a little but I turned my ashtray facility into a map light fixture that, when pulled out, has the Hella three-position switch therein (from the backpad), allowing the driver or passenger to open the map light tray (ashtray) then to choose to turn on the light / but in any case, in passive mode, it simply illuminates the cab when the doors are opened.....

Posted by: rnellums May 21 2015, 09:13 PM

QUOTE(euro911 @ May 21 2015, 01:20 PM)

Posted by: bandjoey Sep 1 2015, 10:43 PM

Received mine today and it's made out of the left over steel from the Battleship Texas! Solid Stainless and in good taste. When the car is a small coffee can of rusty metal this cupholder will be sticking out of the can.

Pictures tomorrow.

Posted by: Hank914 Sep 2 2015, 08:48 PM

Pics?

You want some pics?

I Beta tested this thing over the weekend.

Your basic Double Shot Medium Latte








Attached thumbnail(s)

Posted by: Hank914 Sep 2 2015, 08:53 PM

Posted by: Hank914 Sep 2 2015, 08:55 PM

Posted by: Hank914 Sep 2 2015, 08:57 PM

Yay! Fits the Jumbo Drink from Panda!!!

Posted by: 914socal Sep 2 2015, 09:40 PM

I will take a model 2 when they are ready to ship.

Posted by: keely444 Jul 13 2019, 09:49 PM

Are these cup holders still available?

Posted by: rnellums Jul 14 2019, 06:47 AM

Sorry to say that these haven’t been made in a while. If someone else has interest in carrying on the projects I would definitely provide the files.

Posted by: keely444 Jul 14 2019, 07:44 AM

QUOTE(rnellums @ Jul 14 2019, 05:47 AM)

Posted by: Chi-town Jul 14 2019, 11:04 AM

Can you send me the files?

I may have a way to have a few made

Posted by: FlacaProductions Jul 14 2019, 11:13 AM

Not trying to distract from this but presenting as an option - no affiliation - I found this the other day. Just not sure - when attached to the seat rail - if it would be high enough off the floor to be effective. https://shop.autoracingtechnik.com/collections/accessories-tools/products/porsche-911-carrera-911sc-993-964-944-968-cup-holder

Posted by: Sm914650 Jul 14 2019, 11:20 AM

Id like to order just the #1 ashtray holder please..!.THankU