Posted by: porbmw Dec 19 2013, 12:18 PM
Is the rear circuit board of a 6 the same as a 4?
I'm guessing not....
Am trying to get the 6 done...PO had done a cheap respray in different colour (color to you across the Border)...crappy paint all over the rear panel.
Am I stuck with trying to restore this mess...
Thanks
Posted by: carr914 Dec 19 2013, 01:20 PM
The Boards are Different.
Posted by: toolguy Dec 19 2013, 01:22 PM
As you'd expect, they are NOT the same. . . and you'll have a hard time finding a good one at a reasonable price. . unless someone here has one to spare. . . they can be restored if you do find one
Posted by: porbmw Dec 19 2013, 01:26 PM
Of COURSE they are.....
Thanks
Will see how we do with this.
Anybody have any tricks re getting paint off of plastic.
I have tried a product or two on things I didn't mind destroying....they are destroyed.
Posted by: Mark Henry Dec 19 2013, 03:26 PM
What engine and intake are you planing on using? Is it a real /6 or a conversion?
I'd only worry about a /6 board if it's a real /6.
If it's a conversion some guys run a /4 board and just don't use what is not needed.
Others build a new harness that that plugs into the stock plug and they eliminate the board altogether.
Posted by: Eric_Shea Dec 19 2013, 03:33 PM
QUOTE
Anybody have any tricks re getting paint off of plastic.
Soda blast it. Send it here if you want.
Posted by: porbmw Dec 19 2013, 04:07 PM
QUOTE(Eric_Shea @ Dec 19 2013, 01:33 PM)
QUOTE
Anybody have any tricks re getting paint off of plastic.
Soda blast it. Send it here if you want.
Soda blast!
That is a thought!
I'll see if anyone up here has/does that stuff, or how tough it would be to get a decent little setup going on my own.
If it works on plastic, would be the ticket on a few items!
Will proceed from here, thanks for the info, and the offer!
(It is a real 6.......has Eric's restored/GT brakes...am a luddite, but Jake has taken some pics as he does the re-assembly, am expecting they will get posted in due course. The underneath is getting too pretty....will be a bit of a hurdle to persuade the right foot to get it mobile and full of dirt and grime (well, not THAT much of a hurdle...)
Posted by: 396 Dec 19 2013, 04:12 PM
QUOTE(porbmw @ Dec 19 2013, 02:07 PM)
QUOTE(Eric_Shea @ Dec 19 2013, 01:33 PM)
QUOTE
Anybody have any tricks re getting paint off of plastic.
Soda blast it. Send it here if you want.
Soda blast!
That is a thought!
I'll see if anyone up here has/does that stuff, or how tough it would be to get a decent little setup going on my own.
If it works on plastic, would be the ticket on a few items!
Will proceed from here, thanks for the info, and the offer!
(It is a real 6.......has Eric's restored/GT brakes...am a luddite, but Jake has taken some pics as he does the re-assembly, am expecting they will get posted in due course. The underneath is getting too pretty....will be a bit of a hurdle to persuade the right foot to get it mobile and full of dirt and grime (well, not THAT much of a hurdle...)
Full of dirt and grime..yes just don't drive it during the days she it rains....oh that 89% of the time here in Van BC
....currently in W/B for some runs
Posted by: porbmw Dec 19 2013, 05:42 PM
QUOTE
....currently in W/B for some runs
Geez
Last time I looked, you were up here at the end of summer for a marathon...
Now here at W/B to ski.
I obviously am doing something wrong...
Enjoy