I saw this in the flyer, so I checked it out at the store in San Antonio. It is well made and half way light weight. Extends to about 20" with about a 12x14" rubber coated platform. Upper level comes off if needed. It would be a pretty stable platform to work with for engine/trans removal with out having to balance the trans end while lowering jack. I am probably going to get one for me because I do most of my work alone. Price is $189 but with a 20% off coupon brings it down to $150
Attached thumbnail(s)
Bought one and used it less than 10 times before the hydraulic ram let go... buyer beware!
How did it work though?
I got the same one from Sears.com works good for the tranny. I built a bolt on jig to cradle the tranny.
I've pulled many an air cooled engine with the cheaper yellow one from HF. Indispensable tool in my garage. I even considered it when purchasing a stand. I got a C type stand so I could roll the ATV jack into it with the engine on, then lift it in place with a shop crane or a buddy.
One of my favorite things is that the ram is very good letting it down. The foot pedal on mine has a nice long travel and allows for very slow and small movements.
That and a couple scrap 2x4s will stably and reliably pull engines out of most VWs and the 914. My old westy was the best. The whole ass end came off and you didn't even have to put the bus on jack stands.
I'd say buy it if you plan to pull and replace more than 4-6 engines. If not, find a buddy that has one
One other thing - when you pull the engine/tranny from a 914 as a unit, the tranny will hit the handle frame when you only go down a bit. It's not a problem as long as you keep it stable. It could become a big problem if you let it slide off and drop.
This even helps a bit by creating a slight rake on the assembly, making it easier to clear the half shafts and the trunk. Some bailing wire or a ratchet strap can really help keep it in place on there.
I've pulled my 914 engine with one of those and also used it to pull the trans on my old Mercury, plus numerous other jobs. they're very useful.
here is the one I use, only mine was build on a yellow paint day in China:
http://www.harborfreight.com/1500-lb-capacity-atvmotorcycle-lift-60536.html
It looks like the one you listed above does not have the tranny/handle frame issue. When I just worked on VWs, this wasn't a problem, but something to consider for 914s.
hi,
I bought two of the 3 ton low profile floor jacks from HF.
also bought one of the furniture dollies .
having two floor jacks made the engine removal easy, one would have been a
hassel with constant moving of the jack from side to side as you lower and raise
the car during engine removal/installation.
the furniture dolly worked great for the process. easy to move the
engine/trans around the garage. I do not have an engine stand, so
I just used the dolly and the two floor jacks to elevate the engine/trans as high as
the floor jacks would go, and then placed four jack stands under the dolly.
worked for me.
also.. I think that you can not use the 20% coupon on floor jacks.
it is in the small print on the coupon.
randal
I just re-read the coupon, no discount on lots of items INCLUDING floor jacks.
I have used a regular 3 ton Craftsman Jack along with Chris Foley's 914 Engine Jack Plate for Many. Many Engine/Transaxle Removal and Installs. I have never needed an assistant to hold or balance the assembly in any way. Perfect tool for the job. Even has a cutout for a tuna can. It won't allow slipping of the assembly in any direction and is made to assure perfect balance of the assembly with or without muffler attached. I personally wouldn't go any other way.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)