Printable Version of Topic

Posted by: Mikey914 Aug 10 2015, 08:30 PM

Looking at another run of visors to recover $110 a set in vinyl naked or with flap and pocket, but need 12 sets to do this. Many happy customers, and better than $300+ for a decent set of visors.

Who's interested?

You will need to send in a stripped core (we can strip for $25 more), and we will recover. Shipping is not included in the cost.

-Mark


Attached image(s)

Posted by: wes Aug 10 2015, 11:00 PM

I'm in for a set!

Posted by: LukeD Aug 10 2015, 11:53 PM

Can you clarify what a "stripped core" is, like do I just unstitch or peal off the current material?

Posted by: mepstein Aug 11 2015, 04:43 AM

You just cut the vinyl with a sharp knife and peel off the frame. 3 minutes.

Posted by: Cuda911 Aug 11 2015, 10:21 AM

That's my car in Mikey914's post. His re-covered visors look fantastic in the car. You guys will love them.

Take off your old puffy visors, cut off all the vinyl, throw away the nasty crumbled up foam core, and just send him the wire frames.

Tip: Keep the original screws used to mount the visors onto the pins. They screw into the clips on the wire frame better than replacement screws, so that you can adequately tighten the visors onto the pins.

Another view of the visors (old vs new):


Attached image(s)

Posted by: daraho9146 Aug 11 2015, 10:52 AM

I'll take a set.
PM sent

Dan

Posted by: Mikey914 Aug 11 2015, 11:10 AM

Yep. A bit messy to do and it's just easier to get them ready to go. The $25 extra charge is because we really don't want to do it. You can't hurt anything, just take a knife and slit the edges.

mark

Posted by: mepstein Aug 11 2015, 12:21 PM

I'll take a naked set

Posted by: Kansas 914 Aug 11 2015, 01:25 PM

1 set for me.

Mark, You are going make me come out of retirement!

Posted by: bandjoey Aug 11 2015, 04:02 PM

Very good quality. Only suggestion is to cut the top outside area lower the thick stitching makes it difficult to get the a targa latches through. Se the above old vs new pictures and how the old has more spacing.

Do not let this keep u from ordering. I was in the original buy and happy. These are good quality and worth the money!

Posted by: porsche913b_sp Aug 11 2015, 04:16 PM

Put me down for a set

Posted by: aharder Aug 11 2015, 06:29 PM

I'm in for a set, Missed the first round so I don't want to miss this one.

Posted by: db9146 Aug 11 2015, 08:52 PM

I need this. When do we send the stripped cores and the payment?

Posted by: oakpark Aug 11 2015, 09:41 PM

I'm in for mine. Concours season is over at the end of October and then I'd like to send them. Would that be ok?

Posted by: Jett Aug 11 2015, 09:43 PM

I'll take a set, please send further instruction.

Cheers

Posted by: Mikey914 Aug 11 2015, 10:12 PM

May want to round up a spare set, otherwise ever one will be waiting on you. Camp 914, Mark Epstine, rhodyguy, Brad Mayer. The usual suspects should have a few laying around.

I'll set these up to process through the site that way there will be an order. Just need a few more to open it up. Looks like it will happen, may be a few more days.
Mark

Posted by: JoeD Aug 12 2015, 01:19 AM

I'm in.

Posted by: 914Next Aug 12 2015, 03:46 AM

I'm in if I can find a spare set to rebuild. Posted a wtb in that forum. If anyone has a set to sell pls let me know.

Posted by: AZ914 Aug 12 2015, 11:14 AM

I'm in.. meant to do the last run but somehow lost track of it.. thanks Mark.

Posted by: pvollma Aug 12 2015, 01:00 PM

I'm in for a set. Please post a link to the updated page on your site, as the current group buy page there lists a price of $180. Thanks!

Posted by: relentless Aug 12 2015, 02:13 PM

I'm in if I can find a spare set.

Posted by: dlee6204 Aug 12 2015, 03:52 PM

I'm in for a set

Posted by: Sbradley@netins.net Aug 12 2015, 04:11 PM

so I am new to the 914 world. just bought a 72 1.7 which is in need of a complete restoration. I am interested in the visors. please let me know where to send the visors.
Steve

Posted by: crawler Aug 12 2015, 05:36 PM

Put me on the list.

Posted by: Blue6 Aug 12 2015, 11:28 PM

I'm in also.....

Posted by: RoadGlue Aug 13 2015, 04:26 PM

OK, I'm in for a naked set.

Posted by: MJHanna Aug 13 2015, 08:23 PM

I'm in for a set

Posted by: mepstein Aug 13 2015, 08:42 PM

I do have a set of cores and maybe a 2nd set. I found one but havent found the match yet. maybe this weekend. PM me if you'd like to buy. $40 includes shipping to 914 rubber with your name on it. Cores are in good condition and will be stripped to bare frame.

Posted by: wes Aug 13 2015, 09:42 PM

Is that aimed at anyone in particular if not I'm in for one set.

Posted by: mepstein Aug 14 2015, 04:19 AM

Sent you pm

Posted by: flipb Aug 14 2015, 08:58 AM

Mark,

Please count me in. My original visors live in the front trunk... just having them mounted, I usually end up getting foam dust everywhere. Look forward to restoring to functionality.

Posted by: Shredhead Aug 14 2015, 11:35 AM

I'm in.

Posted by: Mikey914 Aug 14 2015, 02:45 PM

Look's like we can do this. I'll keep the thread open for another week or so. I know I always seem to miss someone.
The cores can be mailed to :
914Rubber.com
21300 NW Cornell RD PO Box 6
Hillsboro, OR 97124

You will need to strip or the fee will apply.

I'll open up the GB on the site shortly, so you will need to identify your shipment so I can match them up when I open it up.

Posted by: RoadGlue Aug 14 2015, 02:57 PM

Awesome, I'll send my cores out next week. Thanks for putting this together Mike!

Posted by: Blue6 Aug 14 2015, 03:49 PM

As soon as I get the car back, I'll send them up. Thank you for the group buy effort, mine look like $hit....

Posted by: crawler Aug 14 2015, 04:43 PM

Do we send you $ with the visor core,or pay you when you ship them back?

Posted by: Mikey914 Aug 14 2015, 06:39 PM

I just need to identify who's is who's.
You will need to place the online. I just finished opening it up.
http://www.shop.914rubber.com/914-visor-rebuild-service-GB-914VRB.htm?categoryId=-1

Us the print and call method for payment if you want to use a check. We do not cash checks until they ship. PLEASE, if you can include a copy of the invoice or invoice number so I can process in order. It will be about 2 weeks before we start, ans these will take a few weeks to complete. The option for plain or pocket is there as well as leather, if you are so inclined.

Posted by: chummasteve Aug 15 2015, 11:51 AM

im in too sent # and name

Posted by: Mikey914 Aug 15 2015, 12:26 PM

Address for shipping is
914 rubber.com
Attn Mark Whitesell
21300 NE Cornell Rd PO box 6
Hillsboro OR 97124



21300

Posted by: RoadGlue Aug 15 2015, 01:10 PM

Paid. Thanks again Mark! I'll send my stripped visors in next week.

Posted by: wes Aug 15 2015, 02:56 PM

Paid and Mark 914name "mepstein" will send them to you. thanks wes.

Posted by: RoadGlue Aug 20 2015, 04:48 PM

(edited - taken care of, thanks Steve!)

Posted by: relentless Aug 20 2015, 05:35 PM

I sent off the metal frames yesterday. I couldn't believe how the original foam had turned into powder, no wonder they looked deflated.

Thanks again for doing this for us!

Posted by: porsche913b_sp Aug 20 2015, 09:50 PM

Just double checking was that Cornell Rd or PO Box 6 ?
Visors will be going in the mail.

Thanks

Posted by: Mikey914 Aug 20 2015, 10:41 PM

We have a PO box at Cornell rd and if it's UPS unit 904.

1 set has shown up so far

Posted by: Blue6 Aug 20 2015, 11:32 PM

I sent them yesterday. Post office said Cornell rd address and the PO box, were to different zip codes.....

Posted by: Mikey914 Aug 21 2015, 01:59 AM

same place 40 ft apart both 97124

Posted by: mepstein Aug 21 2015, 09:04 AM

Got mine today -(mikey had a pair of naked in stock)
Great product - as usual.

You should have Wes and my cores today or tomorrow.


Attached image(s)

Posted by: e_artiles Aug 21 2015, 10:03 AM

Is it too late to get in on this GB?

Posted by: Mikey914 Aug 21 2015, 10:17 AM

No not too late it's still going.
I have it set up on the site -

http://shop.914rubber.com/914-visor-rebuild-service-GB-914VRB.htm

Posted by: AZ914 Aug 21 2015, 01:32 PM

Visor cores are in the mail. USPS seems to have some issue with that street and PO Box combo. Not sure why.. hope they get there!

Posted by: aharder Aug 21 2015, 02:15 PM

You should get mine today, UPS shows by the end of the day

Posted by: crawler Aug 21 2015, 05:18 PM

When I was checking out,it said QTY. Is this for 1 pair @ $110.00 for 2 or is that just for 1 visor?

Posted by: Kansas 914 Aug 21 2015, 06:28 PM

Price is for the pair.

I bought 2 sets.

Posted by: Mikey914 Aug 21 2015, 07:00 PM

3 pairs showed up today !!! And Yes it is $25 to have us strip them, we really don't want to and it allows you to see if all your clips are good.

Posted by: Dominic Aug 23 2015, 09:29 PM

Paid and mailed off the stripped cores on Saturday, sorry for the delay.

Posted by: Mikey914 Aug 24 2015, 12:21 AM

No problem these will hopefully get started this week. Just need 12 sets to get started.

Posted by: crawler Aug 24 2015, 03:59 PM

what address do I use? It was not clear to me.

Posted by: Mikey914 Aug 24 2015, 04:18 PM

USPS add box #6, for any other service we are Unit 904.
Thanks
Mark

Posted by: Shredhead Aug 28 2015, 06:53 AM

Mark,

I put in an order for one pair but want to make it two pair (both stripped). If you tell me what I owe, I'll include a check for both pairs. Will mail tomorrow.

I also have a single visor if anyone needs one (have to check which side).

Kevin Clark

Posted by: mepstein Aug 28 2015, 07:04 AM

side doesnt matter once you strip them

Posted by: Kansas 914 Aug 29 2015, 07:35 AM

Mark,

I put 2 stripped visor core sets in the mail yesterday. You should have them Tuesday. I already put the order in for 2 sets on the website.

I put a copy of the order in the box with the cores.

Posted by: pvollma Aug 29 2015, 09:09 AM

I sent my visors and a copy of the online order via UPS last week, UPS shows they were delivered Friday. I've sent two emails and left a phone message this week asking how to pay for them, but have yet to receive any response.

Posted by: RoadGlue Aug 29 2015, 09:53 AM

You need to pay via his website:

http://www.shop.914rubber.com/914-visor-rebuild-service-GB-914VRB.htm?categoryId=-1

Posted by: pvollma Aug 29 2015, 10:28 AM

Following his earlier instructions, instead of paying online, I selected "Print and call" so I had the order sheet to include with the visors. Your link takes me to the order page, which I suspect will enter a new order not associated with the one included with the visors. Also, his posts here set the charge at $25 for sending covered visors (which I did), but the order page at the time I entered the order set the charge at $10. I need to communicate with 914Rubber.com to find out my total, and to pay for the order. I printed, I called, but have yet to receive a response.

Posted by: JoeD Aug 29 2015, 12:32 PM

My stripped visor cores are on their way, along with a copy of my invoice and check. Thanks!!!

Posted by: relentless Aug 29 2015, 01:09 PM

I sent the metal frames last week and paid on the 914rubber web site. Any idea what the timeframe is for these?

Posted by: Mikey914 Aug 29 2015, 08:13 PM

Must place the order on the site, address for check is
Whitesell Architectural Supply
21300 NW Cornell Rd box 6
Hillsboro OR 97123
If it's no processed through the site we can't keep them in order and track.
We have 12 and are starting them.
Mark

Posted by: Mikey914 Aug 29 2015, 08:15 PM

Some to start shipping late next week to wrap up in about 21 days.
Mark

Posted by: MJHanna Sep 4 2015, 06:32 AM

Finally got my frames sent to me I went on line to create the order on 914 rubber and the price is now $180.00. I guess I missed the window??

Posted by: Mikey914 Sep 4 2015, 10:35 AM

No, The window is open til the end of the month or until all done. We had to get more mirrors made up as the ones I had were damaged. They'll be ready this next week. I did have a few that were good that will be shipping out Tue.
Mark

Posted by: Shredhead Sep 18 2015, 03:08 PM

Still working on them?

Posted by: Mikey914 Sep 19 2015, 08:00 AM

The majority of them will be done this next week. We had to do up more mirrors as the ones I had had got damaged. So the 10-12 sets will be going out this next week with the rest the following. If they are not here by mid next week you might miss out. I will be wrapping this up them.

Posted by: e_artiles Sep 21 2015, 02:46 PM

I made the visor rebuild purchase on your website. I am sending the cores and a check by USPS today. Just wanted to verify the ship to address as:

914Rubber.com
21300 NW Cornell RD PO Box 6
Hillsboro, OR 97124

Posted by: Mikey914 Sep 21 2015, 03:37 PM

Yes.
Please make sure we recvieve no later than Thursday. We are trying to close this out. Should have about 7 sets going out Friday and about that many until we are complete. so 3 weeks they will all be done, if I have by Thursday. It took us longer as the mirrors I had were damaged and we had to do more up. They are all done, and we are moving forward full speed.
Mark

Posted by: Blue6 Oct 14 2015, 10:33 PM

Mark, just checking, have all the visor sets been shipped out?

Posted by: Mikey914 Oct 14 2015, 10:55 PM

No,
We had many stragglers and ran the 1st 20 and are shipping out. We are delayed in that we have to search each order to check to see what needs to be consolidated. We will not be offering this in the future as it slows the process significantly. We are running more this next week and we still waiting for some. We may have to send refunds if not received.
mark

Posted by: JmuRiz Oct 15 2015, 08:27 AM

I wish there was a way to get you a bunch of cores so you could make them and just have them for sale when you have stock...no core needed.

But I'm guessing cores are too hard to come by for that.

Posted by: relentless Oct 15 2015, 10:40 AM

Got mine last Saturday and they look terrific!

Posted by: RoadGlue Oct 15 2015, 11:18 AM

Excited to find out if you received the cores that another member sent you over a month ago. Sent a few PMs Mark but haven't heard back. Realize you're busy. Paid up front, realized I didn't have cores, paid another member decent money for cores, there was a shipping problem and I have no real confirmation that you've received my cores or that I'll be getting a set of visors. Just nervous. Perhaps I've had too much caffeine today! :-)

Posted by: AZ914 Oct 15 2015, 12:01 PM

I received my visors the other day and they look great!! Thanks guys!

Posted by: Mikey914 Oct 15 2015, 10:20 PM

Drop Blake a call tomorrow, 855-914Guys. I know he has more to ship out. He also has a detailed spreadsheet of who paid, when the cores came in and when we shipped. I'm on the road til late Monday.
Mark

Posted by: mepstein Oct 16 2015, 06:41 AM

Mark - do you have time to make one more. Looking for a set of naked. I can ship cores right away. I can probably dig up one or two more sets of cores if you want them for your stock - $n/c to you. Let me know. Thanks

Posted by: RobW Oct 16 2015, 06:53 AM

I missed this the first time around and would love to get in too. NBD if its a "no".

Let me know if Randy still owes a core set. I'm not the member he's referring to, but I can send you a set for him if needed.

Posted by: RoadGlue Oct 16 2015, 10:00 AM

Aww, you guys give me the warm fuzzies (pretty sure that's not an STD...). Thanks RobW!

Mark - I'll call up to the shop today.

Cheers,

Randy

Posted by: Shredhead Oct 19 2015, 03:05 PM

IGNORE THIS, I FOUND PINS...

Hi Mark,

I got my two sets and they look fantastic. Only problem is that I'm missing two pins? I realize now that they probably should have stayed with the brackets, but I think I shipped them with the stripped visors. If they are laying around on the floor of your shop I wouldn't mind getting them. If not I can probably track down a new set.

Kevin

Posted by: RoadGlue Oct 19 2015, 03:17 PM

Called and left a message last week and haven't heard back. Didn't know which dept. to leave the message with so I hunted around on the phone tree and left a message with "Production" (I think).

Anyways, still not sure if you have my cores. You have the funds as I paid for the order right away.

Thanks Mark.

Posted by: Kansas 914 Oct 19 2015, 03:21 PM

I always email Blake at: blake.914rubber@gmail.com

Posted by: RoadGlue Oct 19 2015, 03:37 PM

You are awesome. Thank you.

Posted by: daraho9146 Oct 19 2015, 04:17 PM

Just installed mine yesterday. These are great. Thanks.

Posted by: RoadGlue Oct 19 2015, 04:27 PM

Blake got right back to me via email. My cores are there (whew!) and in the queue.

Posted by: Kansas 914 Oct 19 2015, 04:29 PM

Posted by: RoadGlue Nov 10 2015, 12:27 PM

Still haven't received my set. I heard there was a delay for those that didn't want mirrors, but that was weeks ago. Status update?

Posted by: dlee6204 Nov 10 2015, 03:56 PM

Still haven't received mine either

Posted by: AZ914 Nov 11 2015, 10:11 PM

QUESTION:

Anyone having an issue installing these? I cannot get the passenger visor to stay in the 'up' position, either forward or backwards. It will slowly sag down. I've tried to snug the screws up to the pins as hard as possible, I've tried to shim the pins with some electrical tape thinking the metal bracket is too loose, etc. No luck. The drivers side stays up 'pretty-well' but can start sagging when hitting bumps.

Ended up breaking one of the pins off, so now I'm SOL.

Anyone else have this issue or a suggestion?

Posted by: Mikey914 Nov 11 2015, 11:03 PM

I'm betting the screws were not cut quite short enough. You can file off about 1/16" I do have the old ones I can return but they are not a pretty.
Drop me the name in a PM I'll get you a new visor clip.
Mark

Posted by: Mikey914 Nov 11 2015, 11:05 PM

These are now all complete! they are mailing out in the next day so everyone will have them in a few days.
Thanks for your patience.

We have also acquired some cores that we will be doing up to have these on the shelf. We will charge a premium for the core as we do want to get the old ones back to keep this going. These will be stocked in the next week.
Thanks,
Mark

Posted by: AZ914 Nov 12 2015, 07:14 AM

Ah.. ok, that makes sense. If the screws are a bit too long on mine, they won't allow the ring to snug up. I will give that a try.

Posted by: pvollma Nov 15 2015, 03:20 PM

If you have the mirror style like I do, the flap that covers the mirror on the rebuilt visor is significantly thicker than the original, especially at the "hinge" where it attaches to the visor. The hinge area hits the rubber at the inside top of the windshield before the visor can be placed in the fully up position. I don't know whether this is a design flaw or an attempt to improve the durability of the hinge.

Posted by: Mikey914 Nov 17 2015, 06:27 PM

We did beef up the "hinge" as you can see the OEM ones came off as the plastic got brittle.

Posted by: LowBridge May 6 2017, 05:25 AM

still offering this service and if yes when is the next run going to happen? I'd like to get mine done on this run because it's finally sunny in New England, well almost sunny

Posted by: drem914 May 6 2017, 10:36 AM

+1

Posted by: gcrotvik May 6 2017, 10:41 AM

I'm in for a set.

Posted by: Mikey914 May 6 2017, 12:22 PM

Yes we can open up a new run on these. Need about 10 to make it worthwhile. I have a few I can do up, so really only need about 7-8 to make it work,
Looks like we are 2 in
who else needs these? Price is the same as 1st run. do note we will return the ones you ship in lead time is about 3-4 weeks from when we start.

Also send them stripped to the cores, if not we can do it for $20 extra, but you can save the cash if you do it.

Ill PM everyone when we hit the 10

Posted by: somd914 May 6 2017, 12:44 PM

You did a pair for me on the first run - nice work. Could use a set for the new teener, so I'm in.

Posted by: Big Len May 6 2017, 02:08 PM

I'd be in for a set if it were the winter when i put the car away. i don't want to lose the visors during driving season

Posted by: Chris Scott May 6 2017, 03:28 PM

I would like a set too please.
Thanks

Posted by: markhoward May 6 2017, 03:35 PM

I'm in for a set but do not have cores. Maybe a set will pop up.

Posted by: Mikey914 May 6 2017, 03:46 PM

Try classifieds you should be able to find some.

Posted by: restore2seater May 6 2017, 07:28 PM

I'm in for a set.

Posted by: Evan0 May 7 2017, 12:02 AM

I'm interested in a set.

Posted by: Minerva's 914 May 7 2017, 04:32 AM

Add me to the lot.

Posted by: cooper951 May 7 2017, 05:57 AM

I'm in for a set. Just let me know the process.

Posted by: Robnxious May 7 2017, 07:50 AM

Put me down for a set as well Mark. Thanks

Posted by: 71914-4 May 7 2017, 07:57 AM

I'm in for a set as well, please.

Posted by: NoEcm May 7 2017, 09:21 AM

I'm in for one set with flap and pocket. Thanks!

Posted by: seanpaulmc May 7 2017, 09:53 AM

Mark, put me down for a set as well. They'll go great with all those other interior pieces from 914Rubber in the box waiting on the rust abatement. Thanks.

Posted by: cuddyk May 7 2017, 10:56 AM

LMK if a winter is an option.

Posted by: rob gannon May 7 2017, 11:06 AM

In for a set please

Posted by: TM_Corey May 7 2017, 11:20 AM

I really want to do it, but mine are perfect except the crunchy foam.....arrrgghhhhhh!!!

Let me try and find a replacement set of frames.

Posted by: 9won4 May 7 2017, 11:23 AM

I'm in. Thanks!!

Posted by: dlee6204 May 7 2017, 12:08 PM

I'm in for getting a set done

Posted by: racerx9146 May 9 2017, 01:08 PM

Just paid. Naked style...Will send in cores tomorrow. No more rattling mirror

Posted by: 914Sixer May 9 2017, 01:49 PM

I am in for one set

Posted by: LowBridge May 9 2017, 01:53 PM

3-4 weeks ... it will be winter again in New England if it takes that long

still in on getting a set done

Posted by: Lucky9146 May 9 2017, 03:29 PM

I'm in for a set. Thanks

Posted by: Mikey914 May 9 2017, 04:26 PM

PMs going out shortly,
Mark

Posted by: markhoward May 9 2017, 04:44 PM

Have not found a core set yet. If anyone has a set they don't need, send me a PM.

Posted by: arne May 9 2017, 04:50 PM

I wish this GB was 6 months or so farther out. I want these bad, but I need to stay focused on the important stuff if I'm going to get this car safe and road ready.

Posted by: Mikey914 May 9 2017, 08:45 PM

We can always do the later, just not at the GB price . We can look at a GB later but the key is I need to do at least 10 to offer the better price.

Posted by: Mikey914 May 10 2017, 02:19 AM

PMs sent to all so far.

Posted by: Gulf91474 May 10 2017, 07:12 AM

I'm in for a set.....

Posted by: BENBRO02 May 10 2017, 10:43 AM

I'm in for a naked set.

Posted by: green914 May 10 2017, 11:08 AM

Okay ... I am in for a set.

Posted by: NoEcm May 10 2017, 05:12 PM

Payment and cores sent.

As an observation the cores were not real easy to package efficiently though.

Posted by: bbrock May 10 2017, 09:14 PM

I'm in the same boat. So that is already 2 down and 8 to go for a future GB maybe. I'm fighting hard not to jump on all these great GB offers when I still have so much work before the car is even a roller, let alone on the street.

Posted by: Mikey914 May 11 2017, 10:35 AM

Well, I do have a few sets of frames I can do up, but I must get the cores back. I will charge a $75 core deposit (so I do get them back) if any want these now. I only have a couple sets. if there are any takers let me know and I'll add them to the website.

Mark

Posted by: saigon71 May 11 2017, 01:03 PM

I'm in for one set. Pocket on drivers side, mirror on pass side - just like factory.

I'll strip the cores and mail them early next week.

Thanks!

Posted by: dgraves May 11 2017, 01:18 PM

Mark, I'd like a set, but don't have cores. Do you have any?
Thanks,
Dan

Posted by: markhoward May 11 2017, 01:23 PM

Got my cores lined up thanks to Jeffrey!

Posted by: JmuRiz May 11 2017, 01:33 PM

Is it possible to spec different colors for the thread stitching?

Posted by: mb911 May 11 2017, 02:00 PM

Me too down thr road.

Posted by: Mikey914 May 11 2017, 05:28 PM

Yes, send to us what you want we can use it. Yes it is possible to go back and forth and spec something, but we had one customer that we did that with and spent a lot of time working it out, only to have him say it wasn't the color he thought it was ( didn't like the way it looked when done). So yes we will put any thread you want on, but ask you provide. 90 Bonded Poly works well. Available at many craft stores in less that a full 1# spool.

Mark

Posted by: Mikey914 May 11 2017, 05:41 PM

PMs sent to all there are a few cores available - they in the associated items on the top of the listing so if you need them you can select that way.

Thanks,
mark

Posted by: Bartlett 914 May 11 2017, 06:12 PM

I am if not too late

Web site shows 160.00. Is this too late to get the GB?

Posted by: Mikey914 May 11 2017, 07:06 PM

No only have to sign up so I can send you the code and instructions .
OTW

Posted by: Bartlett 914 May 12 2017, 11:02 AM

cores going out today!

Posted by: adolimpio May 15 2017, 08:06 PM

I'm in for a set.

Posted by: gerber28 May 15 2017, 09:37 PM

Put me on the list, also

Posted by: Mikey914 May 16 2017, 08:02 AM

well we have enough of these in to get rolling, PMs sent to all so far. We will keep tis open for a few weeks, but if you want in get the cores coming!
Thanks,
Mark

Posted by: saigon71 May 17 2017, 09:00 AM

Changed my mind on style...going naked. Cores shipping out today.

Posted by: JmuRiz May 31 2017, 08:07 AM

Get your order in today.
I got my cores and thread last night, I'll place my order today.

Still deciding on pocket/mirror or naked...

Posted by: Chris Scott May 31 2017, 08:29 AM

thanks for the reminder i just placed my order

Posted by: JmuRiz May 31 2017, 07:57 PM

whoops, guess i was too late, message shows they filled their lot and the code doesn't work anymore

I'll wait till next time.

Posted by: Mikey914 May 31 2017, 09:11 PM

No we got 15 and only had that many codes in so I bumped it up. This ends today so get your order in!

Thanks to all that are participating we should be starting to get some out this next week. Also adding in a special for those that want it and are part of the GB.
Mark

Posted by: burton73 May 31 2017, 09:53 PM

I want a set for my 914-6 and want to get into the GB but cannot come up with a set of cores right this minute as the car and original interior is at PMB performance.
Also when I was at your site it said it did not have me under burtonplastics@mail.com but that is my email and I have bought from you before.

Bob B

Posted by: Mikey914 May 31 2017, 11:02 PM

I have the cores in stock looks like 4 sets left. $50, but return serviceable cores and you can get a refund if you can do so within 120 days.
It shows you have placed 3 orders. I just copied the info over and you should be in these I'll pm you the password.
Mark

Posted by: jkb944t Jun 1 2017, 05:40 AM

Mark,

I would like a set too if I am not too late.

Jeff B

Posted by: JmuRiz Jun 1 2017, 06:58 AM

Great customer service Mark...it's a win-win, you got more orders than expected! Getting my order submitted now.

Posted by: Bartlett 914 Jun 1 2017, 08:29 AM

What is the ETA on receiving these?

Posted by: Mikey914 Jun 1 2017, 11:24 AM

Will be filled in order received, and some will be starting to be done this Friday!
Shipping them Monday

Posted by: Lucky9146 Jul 9 2017, 01:00 PM

Mikey can you give us a status on visors please. Mailed mine in on May 13.

Thanks,
Jim

Posted by: ConeDodger Jul 9 2017, 02:12 PM

Love mine! So much better than the flimsy vinyl originals that get all puffed up and worn out looking!

Posted by: Mikey914 Jul 10 2017, 09:28 AM

Yep, I'll have Scott following up with those that are still to ship. we did have a slow down is resolved and things are getting done now.
Mark

Posted by: JOEPROPER Jul 10 2017, 12:04 PM

Do you have room for one more set?

Posted by: NoEcm Jul 22 2017, 07:56 PM

Cores mailed in May 10, 2017

Rebuilt Visors arrived today in Seattle, WA USPS Priority Mail July 22nd.

Good fit and finish at a very reasonable price.

Thanks a bunch for a great product!!!

Posted by: Mikey914 Jul 22 2017, 08:36 PM

supposed to be complete and shipping the balance Monday
Sorry it took longer than planed

Posted by: NoEcm Jul 22 2017, 10:15 PM

Not a big deal, it was worth the wait.

Posted by: seanpaulmc Jul 25 2017, 11:20 AM

Wanted to give a shout out to Mark and the team at 914Rubber. Got my visors back and they are outstanding quality. Best looking thing on my car now (I have to get working on that).

Posted by: markhoward Aug 9 2017, 10:57 AM

Got my visors a couple weeks ago. Superfly!! Thanks Mark!!!

Posted by: Guberif Aug 9 2017, 02:33 PM

I'm in too! sending pm

Posted by: drem914 Aug 10 2017, 02:37 PM

Visors showed up today and look great!
Thanks,

Posted by: rob gannon Aug 11 2017, 11:17 AM

Received visors last night, they look awesome!!
Thanks Mark!