Leaning towards an epoxy product. Any recommendations would be greatly appreciated!!
Thanks
Rob
Do yourself a favor and consider a porcelain tile floor for your garage. Harder then cement and look terrific.
You'll find 2 types. One is about 40% more than the other. That's the one. If it is an old floor you might consider a pro application w/ a warranty against flaking/peeling or bubbling. A novice can handle a new homes floor but old ones are Hell to properly prep. That being said; get one. It's so nice cleaning up oil spills with a swipe of a rag. FWIW, avoid parking on it if you just came off the hi way in summer temps. If you do, the epoxy paint tends to stick to the tire if not prepped correctly.
I thought about porcelain tile floor but I have a 5000 Lb. rated forklift I'm not sure if its too much weight for floor tile? Since its rated at 5000 not sure what the actual weight of the forklift is...
Thanks,
Steve
I still just prefer a clean concrete garage floor.
-Steve
I have used this stuff on two garage floors. Once it's cured, it does not react with the rubber in your tires. Prepping it properly and letting it cure long enough are the key. The prep. being most important. http://www.griotsgarage.com/product/tan+floor+paint+one+gallon.do?sortby=ourPicks&refType=
Rubber floor tiles
I used a rustoelum product I got from Menards. I used the solvent based product not the water based stuff. I used the light grey and skipped the plastic flakes. It is an epoxy mix and it was a bit expensive but it did hold up well. I am due for a recoat but it received hard use and lasted several years. Easier to clean than concrete surface. The biggest improvement was light. It was incredible how much brighter the shop became after painting
Used the rustoleum product from HD. It is a two part epoxy.
Have used it on two floors now and very pleased. It is bright, durable, easy to clean,
and does not lift onto the tires. And it is affordable.
Proper prep is a must or you will be left with a mess. Follow the directions to the letter. The prep will take two long days of scrubbing, degreasing, scrubbing, rinsing drying, etc. The application goes quick.
The epoxy must be catalyzed properly (the correct time for the temperature). IF not done correctly it will never fully cure and again- a mess.
The color batches vary slightly. Rustoleum advises to mix several gallons in a 5 gal bucket then refill original containers prior to adding catalyst. I mixed enough to set aside a spare gallon for future touch ups.
+1 for the tiles. The guys and women at Race Deck have always been good. Not to mention, you can have more flexibility with the design. And if a tile or two go to pot, you just replace them.
http://www.motoroso.com/racedeck
Thanks guys!!
The Behr garage floor paint from Home Depot sucks. I wish I had spent the extra couple of bucks on the epoxy stuff.
Konrad
If I can recall correctly, race deck is a plastic tile, with holes in it to allow dirt to go below. Not something I would use.
When I say rubber floor tiles, think commercial tiles like what you see on stairs at large office buildings.
It comes in tiles or 12 foot wide rolls, as long as you need.
It weighs a ton.
It can take your forklift weight.
It is a lot easier to install than paint.
Attached image(s)
I think this would work great... But anybody got a link on where to buy it and how much it costs?
Thanks,
Steve
http://www.sears.com/incstores-coin-pattern-nitro-garage-floor-mat-covering/p-SPM7465836902?prdNo=25&blockNo=25&blockType=G25
There are many other colors....that was just one
i have a 2 car cement garage. I stripped painted (walls and floor) with the proper paint and...
have always had antique automobiles and learned early that keeping the floor covered with tarp prevents rust. it has worked over 30 years. try it ....
914 luva
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)