I read a post on Pelican where you put a open end wrench underneath it and hit it upwards with a hammer.............
Is this really the way ? And if so does it wreck the compression fitting or is it reusable ?
I bought a NOS leather with Porsche logo knob that I would like to replace it with, just find it hard to believe that you smack up on it to come off then smack down on it to go on ???
Just pull it off. Never had to use hammer.
I don't even know what a crush ring looks like ? Does this have one.
That type was not the AMCO one more widely sold by dealers, but from the period anyway.
However, it looks like the threaded type down in the hole, which IIRC was used on some 356s & early 911/912s with threaded shift shafts. Not sure it will fit on your shift shaft, unless it is threaded.
Crush Sleeve & a repro 901 shift knob are shown at this link below from SMC, but other suppliers may be better sources nowadays.
http://www.sierramadrecollection.com/914-914-6-70-76-/Pedals-Shifter-Parking-Brake-Assembly/Shifter/Shift-Knob-Crush-Sleeve-65-86-p19751.html
I don't know what you paid for that knob - which is a painted vs. cloisonne crest, but if it doesn't fit, then I think AA sells a newer cloisonne version with a black trim ring for not too much, plus Porsche Classics is making the original 901 5-spd pattern ones new again & available from dealers & other parts houses like Stoddards $ Einmalig for about $175 IIRC.
Sometimes the original AMCO cloisonne crest ones in walnut to leatherette come up on evilbay for not too much in good used to NOS condition as well.
It would insert into the hole to fill the gap tightly when pressed onto the shaft.
Look for the Porsche crest cloisone (which is essentially baked glass) & its surrounding metal ridges separating the colors in the best possible condition without chips, cracks, oxidation of the metal, etc. - & the leather/vinyl can be not so good - since you can get a local upholstery shop to recover it, along with your steering wheel leather (or at Dallas Steering Wheel) & the leather shift boot (if a center console 914) - all in the same leather.
Personally I like the look of the crest & can remember the shift pattern just fine!
BTW - I could never just pull my knob off as Mark/914sixer said, but by just tapping it off with my "U" wood bit described above usually worked it off cleanly. I just was being facetious when I said "banging" it off above.
Good Luck!
Tom
///////
Thanks for the info Tom, and yes got if off eBay from some guy in Hawaii. I had the one you described on my first 914 many years ago, I just couldn't remember all the details. It looked the same to me. Bad news it was 40.00 bucks. Good news is it's one more thing I will bring to the next So Cal 914 swap meet.
Does that knob have small threaded holes near the base for a couple of set screws? They never seem to hold. Does the knob slip on tight or kind of sloppy? I have a shift lever that the po used epoxy or the like to keep the knob in place. Almost a good idea except the knob can not be removed and thus if one ever wanted to replace the bushings that cradle the lever ball or any other service to the shifter assem it's impossible. You can't even remove the rubber boot. Same if the lever has worn excessively at the detent plate contact point. The leather covered knob is now garbage.
Every crush sleeve knob I've ever encountered came off with a bit of muscle.
I don't like the idea of using a hammer here.
Btw, for a stock knob with the sleeve, simply turning the knob and pulling it comes off. Look for set screws on the base of yours.
[quote name='Tom_T' date='Feb 11 2016, 08:02 AM' post='2301666']
Coondog - if that's NOS or even excellent condition used, $40 isn't a bad price at all.
I'm 5-10 mins from the Phoenix Club & will go over if I'm in town that date this year (I've been away the past 2), so will catch you there, if you venture down from Apple Valley (PM or email me if you plan to).
Yes Tom I have it on my calendar, all good on the rest of the interior but would like to find a leather knob with the Porsche crest that will fit. I will bring mine just in case someone wants to trade.
Hope to see you there, I will be wearing a Orange, Stoddard 914 parts shirt.
Greg
Another vote here for the slotted board trick. The previous owner glued the knob onto one of my cars. There was no way it would pry off.
I cut a U-shaped slot the width of the shift lever, about an inch or two long, into the end of a short board. That way, you can wack it good from the bottom with a hammer and not damage anything
The crush washer looks like a little corrugated metal cylinder.
I tried the open wrench and mallet..... once. I now have a cracked shifter hand I e.
Nevef again.
[quote name='Coondog' date='Feb 11 2016, 08:49 PM' post='2301989']
[quote name='Tom_T' date='Feb 11 2016, 08:02 AM' post='2301666']
Coondog - if that's NOS or even excellent condition used, $40 isn't a bad price at all.
I'm 5-10 mins from the Phoenix Club & will go over if I'm in town that date this year (I've been away the past 2), so will catch you there, if you venture down from Apple Valley (PM or email me if you plan to).
Yes Tom I have it on my calendar, all good on the rest of the interior but would like to find a leather knob with the Porsche crest that will fit. I will bring mine just in case someone wants to trade.
Hope to see you there, I will be wearing a Orange, Stoddard 914 parts shirt.
Greg
[/quote]
Greg - keep watching evil-bay & CL & TheSamba.com classifieds.
Also, look at Auto Atlanta or call George the & see if he still has the newer version of them with the black trim ring around the crest, since those will fit 914 & 911.
Also Einmalig in Huntington Beach may have some of them too in their deep stash.
So ... El Camino or 914 to the Pheonix Club in March!? Toough choice buddy, but a great one to have!
Tom
///////
[quote name='slotty008' date='Feb 19 2016, 11:40 AM' post='2305095']
[quote name='Coondog' post='2301414' date='Feb 11 2016, 01:57 AM']
I read a post on Pelican where you put a open end wrench underneath it and hit it upwards with a hammer.............
Is this really the way ? And if so does it wreck the compression fitting or is it reusable ?
I bought a NOS leather with Porsche logo knob that I would like to replace it with, just find it hard to believe that you smack up on it to come off then smack down on it to go on ???
[/quote]
Can you tell me where you found the leather Porsche shift knob?. I have an aluminum Momo shift knob wich I don't like and I'm not a big fan of the original black shift knob.
[/quote
eBay, seller was not a Porsche vendor. He had it in a box in his garage for 20 plus years.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)