Printable Version of Topic

Click here to view this topic in its original format

914World.com _ 914World Garage _ Fuel line grommets

Posted by: Cornerlot Jul 12 2016, 07:50 AM

I'm new to 914's, previously I've just fooled with 911's.

I now have a '70 914-6 with the fuel tank out and need to replace the rubber grommets for the fuel lines. These are where the 2 fuel lines (different O.D.'s) enter the tunnel under the tank, both going through their own OVAL holes (one line per hole).

Any ideas? The closest I found are the PN 111957861 oval grommets for the brake reservoir lines and fuel in the 914-4 engine bay. The PET shows both a NLA single large oval grommet in some cars set up for 2 lines, or a un-pictured NLA grommet PN 99970209550 for single lines.

Steve

Posted by: napasteve Jul 12 2016, 08:34 AM

Your 914-6 setup is different than my 73 2.0 pictured below. I reused my single big grommet when installing SS lines; it was in good condition. You might contact Chris at Tangerine Racing. He may be able to help you.

Attached Image

Posted by: altitude411 Jul 12 2016, 08:57 AM

Mark carries these 10 mm as well as 8 mm.
http://shop.914rubber.com/Fuel-line-grommet-10mm-10mmFLG.htm

Posted by: Rotary'14 Jul 12 2016, 10:03 AM

Hi,,
914-6 has front grommets similiar to the engine shelf grommets. I have those available at $4 each plus shipping.

-Robert

Posted by: Mikey914 Jul 12 2016, 10:36 AM

Yep, I have the rear ones. If you can't find what you need. I can probably make it. Just let me know.


Attached thumbnail(s)
Attached Image Attached Image

Posted by: Cornerlot Jul 12 2016, 11:24 AM

QUOTE(Mikey914 @ Jul 12 2016, 12:36 PM) *

Yep, I have the rear ones. If you can't find what you need. I can probably make it. Just let me know.


The round ones won't work, they are larger and oval. The engine shelf ones may work. Right now I have the stock lines, so angled 8mm and 10mm should work.

Steve

Posted by: Cornerlot Jul 12 2016, 11:26 AM

QUOTE(napasteve @ Jul 12 2016, 10:34 AM) *

Your 914-6 setup is different than my 73 2.0 pictured below. I reused my single big grommet when installing SS lines; it was in good condition. You might contact Chris at Tangerine Racing. He may be able to help you.

Attached Image


That 914-4 grommet is larger than my single line grommets. The dual line one is NLA any ways.

Steve

Posted by: Cornerlot Jul 12 2016, 11:36 AM

A picture before they fell apart ...

Attached Image

Posted by: Dave_Darling Jul 12 2016, 05:06 PM

Those do look an awful lot like the engine shelf grommets.

--DD

Posted by: Mikey914 Jul 13 2016, 12:34 AM

Well I have these, which I think you may be referring to. They are the larger ID

http://shop.914rubber.com/Vent-hose-bushing-823823591-99970204950-set-of-2-99970204950.htm


Attached image(s)
Attached Image

Posted by: Mikey914 Jul 13 2016, 12:38 AM

And of course these on the fuel shelf

http://shop.914rubber.com/Vent-hose-bushing-823823591-99970204950-set-of-2-99970204950.htm


Attached thumbnail(s)
Attached Image

Posted by: Cornerlot Jul 13 2016, 08:10 AM

QUOTE(Mikey914 @ Jul 13 2016, 02:38 AM) *

And of course these on the fuel shelf


The fuel shelf ones look more oval, and those charcoal canister grommets have holes too big. I'll order the fuel shelf ones and give them a try.

Thanks.

Steve

Posted by: Mikey914 Jul 14 2016, 12:28 AM

thanks Steve,
They are elliptical, the angle of the photo is distorting the perspective. Yes my photography sucks.

Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)