I just finished installing an overhaul kit in one of my 44idf's. It runs great now except for a stubborn fuel leak at the large 19mm filter holder plug just next to the fuel intake. The one that holds the small white filter. That one. I can't get it to stop leaking. Not a pouring out leak but a drip per second leak. I tried loosening it, tightening it and using two gaskets together and it still leaks. both surfaces look clean and smooth. Any ideas?
Cooper crush washer, or the red fiber crush washer? If it's a fiber crush washer, soak it in low viscosity motor oil or gasoline for an hour. Wipe off the excess oil, and reinstall. Soaking it in gas or oil allows the fiber washer to swell up, and facilitates sealing. To be honest, if you left it sit overnight, then tightened it a little bit in the morning, it would seal, but this method guarantees it will seal the first time out.
Common problem with new fiber sealing washers. I'm assuming they are the fiber ones, as pretty much all the rebuild kits I've seen include the fiber washers...
Threebond 1104, Yamabond is the same thing except rebranded by Yamaha.
Light bead on each side of the aluminum or fiber washer.
Try loosening and tightening it softly a couple of times to set the gaskets in place
If with the gasket in place you have a leak, most likely you have some damage of th mating surfaces.
Typically, unless it's a huge gash, the gasket will make up for,the difference...
Are you using a gasket there?
What type?
Is it the right filter or maybe it's holding the part. Just a hair.
I know there are what, 10 different accelerator pumps for them....maybe there are multiple filters and you got one too tall.
Jbweld.....had to be said.
[quote name=''73-914kid' date='Jul 24 2016, 06:13 PM' post='2375964']
Cooper crush washer, or the red fiber crush washer? If it's a fiber crush washer, soak it in low viscosity motor oil or gasoline for an hour. Wipe off the excess oil, and reinstall. Soaking it in gas or oil allows the fiber washer to swell up, and facilitates sealing. To be honest, if you left it sit overnight, then tightened it a little bit in the morning, it would seal, but this method guarantees it will seal the first time out.
Common problem with new fiber sealing washers. I'm assuming they are the fiber ones, as pretty much all the rebuild kits I've seen include the fiber washers...
[/quote
I soaked it in oil for a few hours and re-installed it. It looks like that might have done the trick. Thanks for the tip.
[quote name='Elliot Cannon' date='Jul 25 2016, 10:00 PM' post='2376554']
[quote name=''73-914kid' date='Jul 24 2016, 06:13 PM' post='2375964']
Cooper crush washer, or the red fiber crush washer? If it's a fiber crush washer, soak it in low viscosity motor oil or gasoline for an hour. Wipe off the excess oil, and reinstall. Soaking it in gas or oil allows the fiber washer to swell up, and facilitates sealing. To be honest, if you left it sit overnight, then tightened it a little bit in the morning, it would seal, but this method guarantees it will seal the first time out.
Common problem with new fiber sealing washers. I'm assuming they are the fiber ones, as pretty much all the rebuild kits I've seen include the fiber washers...
[/quote
I soaked it in oil for a few hours and re-installed it. It looks like that might have done the trick. Thanks for the tip.
[/quote]
Keep a close eye on it. watched a local teener burst into flames at the last autocross after it lost a plug from a carb. Needless to say it didnt help my opinion of carbs....
I think I finally got something that would stop the leak. I bought very thin 1/2 inch mylar washers, opened them up to 9/16, squeezed one of them over the threads of the plug, installed it and so far no leaks. I'm pretty sure the mylar will hold up. I'm told mylar never deteriorates. Ever.
Also, for future work, get an extra 6 sided 19mm and shave it down so the mating surfaces are perfectly square. It helps you get some torque on that fitting without damaging it.
I think so
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)