This is an "improved" kit that uses a slightly softer high temp silicone to seal the cover plate that joins the blower housing to the sheet metal portion of the heat exchanger on the bottom.
I have included 4 allen head screws with washers. These allow you to get good tension on the screw, and to remove easily without destroying the screw.
I can provide as cork if you prefer at the same cost, but This should be a reusable gasket that is now inexpensive!
Compare to
021256325A
and
021256326A
These go where the sheet metal attaches to the blower. The ones I removed were pitiful. Most are missing completely.
http://shop.914rubber.com/021256325A-021256326A-Heater-blower-plate-gasket-kit-0212563256A.htm?categoryId=-1
Attached thumbnail(s)
Nice mark. They used to be cost prohibitive elsewhere.
Nice Mark. I'm definitely in for a set. I need my heat this time of year
I'll take a set right now. Working on the heat for my car right now. Had no idea these even existed!
PMs sent
Want.
Just got a new set of brackets from bstone.
3 sets for me.
Put me down for a set, Thanks
1set
I'll take one set!
1 set, please!
PMs sent to all
I'll take a set. Thanks.
I'm sure that my daughter's car will need one...and I probably do as well.
Two, please
A set for me too Mikey !
Sir Mike one set for me too.
I never even knew those existed! 1 set for me please.
I'm in for a set of the silicones. Let me know.
I will take a set. Is there an update on the CHT senders or did I miss it?
one set for me.....
PMs sent to all -
The CHT GB closed, but I
If you bumped the thread You should have got the code. It's possible I missed you, but I'll take care of you
Mark
Mark,
I need to get a set of these gaskets if the GB is still open
thank you
brant
I'm in for a set. Sent you a PM, but not sure you got it .Thanks
Jesse
I'll take a set for the creamsicle which is currently missing these gaskets.
Can these gaskets be replaced/installed without removing the heat exchangers?
I'm thinking the allen screws might make it possible without removing them.
I would like one set of these seals in silicone, please.
PMs sent to all so far.
I am a bit confused you have 3 different prices for these. You have 2 different numbers which I believe are for 2 different sizes and another price of $20.00 for a pair(?). Would you please elaborate?
Thanks,
Buck
I have 3 different listings
one for the 021256325A gasket alone
http://www.shop.914rubber.com/021256325A-Heater-blower-plate-gasket-021256325A.htm?categoryId=-1
One for the 021256326A gasket alone
http://www.shop.914rubber.com/021256326A-Heater-blower-plate-gasket-021256326A.htm?categoryId=-1
And the one that should have been in the PM I sent with the code for all that bumped the thread - The Kit with screws
http://www.shop.914rubber.com/021256325A-021256326A-Heater-blower-plate-gasket-kit-0212563256A.htm?categoryId=-1
The discount code only works on the kit.
Mike
Please count me in for one "Iimpvved kit"). Send a PM cost details.
Thanks,
Matt
Please put me down for one also, Mark. Thanks!
P.S. Any way to combine this order with your upcoming Black Friday specials?
Just saw this today.. I want a set too.
BTW: I showed my local Porsche mechanic your 1.8 Throttle Body gasket; he really liked it !
PjMs sent to all
Mark, I just saw this ... I was in AZ working on the new house and not on the board very much
I'd like to get two sets of these gaskets ... Too late for the discount?
I really need to go to the site and see what other great new items you've released recently
Mark,
Please count me in for a set if still available.
Thanks, Marty
Ok. Merry Christmas
Just dropped these on sale on the site
http://shop.914rubber.com/021256325A-021256326A-Heater-blower-plate-gasket-kit-0212563256A.htm?categoryId=-1
Thanks Mark ... I just sent in an order for a bunch of little goodies
Ordered and PayPal sent.
Left it open til Christmas for those that missed it.
... and the little mouse trap doors that go inside
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)