I played around with photoshop a little bit. I hope 914RS doesn't mink I used his picture.
Anyway, instead of having a tube go from the ear to the firewall, I thought that one could take some sheetmetal and create a shelf. I don't thin this will work for /4 but it might for converted cars. I thought a cross section might look like
_____
|_____\__________
Would this be strong enough? Just seeing if there is a nice way of doing the brace. So It would be like having another shelf. I don't know how low the engine mount goes but I think one could work around that. On the ear the attachment point would be pretty low and be able to handle movement better. On the firewall site it would attach to the back edge of the floorpan.
Attached image(s)
As long as the box tubing is substantial enough, I think that would work fine.
In that case the question becomes, what is substantial enough?
Hey smrz914,
Here is the way we do it to all our hot rods and race cars.
We box the almost all of the suspsion console with 12Ga like the GT stiffing plates.
The ReaL week point is the lower section of the ear.
It takes the most load. The tubing is good to add also
Here's some pics.
Attached image(s)
another
Attached image(s)
QUOTE (smrz914 @ May 3 2005, 08:18 PM) |
In that case the question becomes, what is substantial enough? |
I did my race cars similar to Porsche Doc. I fishplated the console and then added tubing. My tubing goes through the firewall and ties into the cage.
The shelf idea is interesting, but what are you attaching it to at the front? (the floorpan?) You may need to add some strength to that if you tie in there.
To add stiffness to a structure, your anchor points must be substantial, or you are wasting your time.
If you decide to go ahead with the shelf and rectangular tubing, I would consider adding some drain holes to the shelf.
just my $0.02
Don,
I didn't see you and Charles at the Mitty. What happened?
Thanks guys I'll have plenty to mull over for a while. I'm just making plans for my project. Porsche Doc, did you add metal to where the trailing arm bolt goes through the ear, possibly requiring a longer bolt, or was that left the stock thickness, and metal added around where the nut would be?
here's what I'm planning to do
weld a piece of 2" tube around the nut
then tie braces to that (braces will be weld to both the 2" piece of tubing as the susp.ear itself)
All the cracks I've seen are either at the nut or just above it
I feel the braces pictured above don't reinforce that area
This should
Attached image(s)
QUOTE (Jeroen @ May 4 2005, 07:51 AM) |
here's what I'm planning to do weld a piece of 2" tube around the nut then tie braces to that (braces will be weld to both the 2" piece of tubing as the susp.ear itself) All the cracks I've seen are either at the nut or just above it I feel the braces pictured above don't reinforce that area This should |
QUOTE |
Watch your clearances there Jeroen - that area is close to the engine. |
When adding structure to the ear and extending it to a remote location, any flexing in the chassis that is realized between those to points may cause undue transfer of loading to the ear. This may cause the cracking/failure you're trying to avoid in the first place. A localized structure that spreads the loads I would think to be a better solution. If you have a full cage, then this may not be an issue.
Andy
QUOTE (Brett W @ May 4 2005, 12:12 AM) |
Don, I didn't see you and Charles at the Mitty. What happened? |
Yeah 400+ cars. The 914 crowd didn't really make a great showing. Most broke or also ran.
QUOTE (andys @ May 4 2005, 08:45 AM) |
When adding structure to the ear and extending it to a remote location, any flexing in the chassis that is realized between those to points may cause undue transfer of loading to the ear. This may cause the cracking/failure you're trying to avoid in the first place. A localized structure that spreads the loads I would think to be a better solution. If you have a full cage, then this may not be an issue. Andy |
QUOTE (Porsche Doc @ May 3 2005, 08:06 PM) |
Here is the way we do it to all our hot rods and race cars. |
Hi
I followed a couple topics like this and got some real help. My experience has been that they break at the bolt hole across, then fold outwards to the direction of the fender. I wonder if Brants broke this way.
My research left me to understand that, if the ear is in good condition, its ok for almost anything on the street. If it is so-so but save-able, it should be re-inforced.
I just don't think the solution offered here has any real benifit for the street. I look hard at mods to preserve my car....still looking at it.
Later..
Joe
QUOTE (JoeSpark @ May 4 2005, 04:13 PM) |
Hi I followed a couple topics like this and got some real help. My experience has been that they break at the bolt hole across, then fold outwards to the direction of the fender. I wonder if Brants broke this way. My research left me to understand that, if the ear is in good condition, its ok for almost anything on the street. If it is so-so but save-able, it should be re-inforced. I just don't think the solution offered here has any real benifit for the street. I look hard at mods to preserve my car....still looking at it. Later.. Joe |
Any more pics Jeroen?
This is an area I will be reinforcing at my next engine pull... (probably soon...)
And I want it to be able to hold the v8's tq on hoosers with rock hard suspension...
Probably get a good welder and helmet before this as well.. lol
Andrew
Jeroen has a good idea. Something I rarely see is support running BOTH directions. He addresses this.
JP,
IF, I build another car for myself.. I will do exactly like you spoke: peel the top cover off the ear and weld in a scab plates.. then weld the "cover" back on. I do not like any of the tubes leading into the front of the ear. Most people use small tubing and all it does is crack at the point where they welded to the ear.
Great discussion and good insight.
B
here are a few inner ear pictures I collected over the years...
Attached thumbnail(s)
I'm saying I like this but here it is..
Attached image(s)
other side
Attached image(s)
last
Attached image(s)
QUOTE (Brad Roberts @ May 4 2005, 05:20 PM) |
IF, I build another car for myself.. B |
Paul:
The black one don't look too bad, but I'd have to get a better look at the other sides. Nice stout plate, tho. Can't really tell what it ties into at the topo
The gray one.....I've seen the ear break off just below where that tube ties in.
I've seen some really nice looking (Strong, not pretty) done when guys raise the swing arm mounts.....got a pic here somewhere.....I think.
I'm gonna have to do something in this area. My new (IMPROVED!!) tiars are gonna raise hell with my chassis, me thinks.
(edit)
Humm....I really should take a close look at a pic before I post it
Attached image(s)
Well that ought to stiff enought!
Added 20 lbs to the car too.
Hey Jeroen
The front and rear bar is a good idea. But you would want to cope the tubing into the ear so that it dosen't stick out pass the inside face more than the thickness of the material 1/8".
I also would still plate it like we do before adding the tubing.
Then you would have something workable.
There is more steel there than in the roll bar!:o
Paul
QUOTE (URY914 @ May 4 2005, 06:15 PM) |
There is more steel there than in the roll bar!:o Paul |
QUOTE (J P Stein @ May 4 2005, 06:40 PM) | ||
There's more steel there than in your whole freakin' car |
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)