Have some movement @ the front securing bracket ,is that normal or is it starting to break ?
Reason I ask is I have had to adjust my new clutch several times,maybe my new cable is continually stretching as I have set to correct freeplay on every occasion.
Had my gearbox out to replace input shaft seal and besides minor oil contamination (cleaned up ) it was well....a new clutch.
TIA
Sounds like it's more than starting.
I'd reinforce in the tunnel and at the firewall in the engine compartment, and the sooner the better. Even if it was something else, this is an upgrade we'll all need at some point.
The front should not move at all. It is just a small amount weld attaching the tube to the body up front.
This is a problem on 914s and there are lots of write-ups on it. It comes lose at every place it is welded to the car.
Not so easy to fix completely without having the metal on the bottom opened up. Lots of creative temporary fixes but you need to look up old postings and see the ways people have done this over the years.
You will see u bolts jobs, welding part of it. Remember that your gas runs through the center tube as well as wiring and more. When you see some pictures you will have a much better idea of what you have to do.
Bob B
You can remove the bolts from the shifter base, turn the base 90 degrees and with a flashlight see that front weld joint to see if it broke loose.
Researched and found the spot welds holding the bracket are 3'' forward of the shifter is this correct before I start ?or this this case grinder.
Do the research on old postings. I find that it is easer to look up questions on Google asking something like “clutch tube lose on 914 Porsche”
I find it is much easer that using the search engine in on our site.
Look at all the pictures and people show their different fixes for this problem. To fix it for the longer run as I said you have to open it up but you may use a U bolt and nuts for a somewhat long fix. See what that looks like. With that fix there is no welding just drilling and bolting. My 6 was fixed that way when I got it and I have no idea if it worked right or for how long. I fixed it right when I went in for the full restoration of her.
You have to be very careful in any drilling or cutting because of possible damage or fire.
It is hard to see clearly in your picture, as it is too dark.
Bob B
Do the research on old postings. I find that it is easer to look up questions on Google asking something like “clutch tube lose on 914 Porsche”
I find it is much easer that using the search engine in on our site.
Look at all the pictures and people show their different fixes for this problem. To fix it for the longer run as I said you have to open it up but you may use a U bolt and nuts for a somewhat long fix. See what that looks like. With that fix there is no welding just drilling and bolting. My 6 was fixed that way when I got it and I have no idea if it worked right or for how long. I fixed it right when I went in for the full restoration of her.
You have to be very careful in any drilling or cutting because of possible damage or fire.
It is hard to see clearly in your picture, as it is too dark.
Bob B
Here's a good reference for starters:
http://www.914world.com/bbs2/index.php?showtopic=28313&hl=clutch+tube+repair
Thanks Bob and rand,picked up on Spokes repair was just confirming before I cut,I can't see a thing up there with a torch ??,the link provided has given me more good info .
No I don't plan on using u-bolt that's a bit hillbilly to me,I have started to make I clamp bracket I will weld to the base of the tunnel,hopefully fixed to the original one.
All good on the proximity of the fuel lines,mine is metal towards the rear going to new plastic line @ that point next to the shifter.
Not too concerned as I would like to paint the bottom of the tunnel so now is my change and I may do the rear bracket too.
Thanks all for comments.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)