plz?
thank you. trying to show someone...
i have been denied by
AAron Cox
Sure. Hold please.............................................................................................................................................
QUOTE (skline @ May 10 2005, 08:33 PM) |
Sure. Hold please............................................................................................................................................. |
One ringy dingy, two ringy dingy, snort***snort, three reingy dingy.....
QUOTE (SLITS @ May 10 2005, 08:39 PM) |
One ringy dingy, two ringy dingy, snort***snort, three reingy dingy..... |
Medic.....sure hang on I have a tape...............
One a two a three............Ooops...that's the wrong tape....dam Jane Fonda workout....
and then?
I think he passed.......I did find my Eddie and the Crusiers tape tho.....so some good came out of this....
Here is a picture of a nice fitting Tee
Attached image(s)
Sorry, wrong pic, try this one.
Attached image(s)
My mom is out again... must be dinner time for someone.
M
QUOTE (Mueller @ May 10 2005, 09:03 PM) |
Mmmmm, brass nipples make me HOT.....
where can you buy that adapter?
BTW- did you have to mod the caliper to clear your rim scott?
You would need two if your only doing 1/2 your car
here is the drawing for it...not too hard to make at all........
QUOTE (Aaron Cox @ May 10 2005, 09:08 PM) |
where can you buy that adapter? BTW- did you have to mod the caliper to clear your rim scott? |
QUOTE (Mueller @ May 10 2005, 09:11 PM) |
here is the drawing for it...not too hard to make at all........ |
QUOTE (skline @ May 10 2005, 09:13 PM) | ||
Mike, since you have it all right there, why dont you make up a few dozen and sell them. I would take a couple of them. I am pretty sure Aaron will too and maybe Bernbomb as he runs the same calipers on his car. |
lemme price up the material...they should be pretty cheap.....
QUOTE (Mueller @ May 10 2005, 09:21 PM) |
lemme price up the material...they should be pretty cheap..... |
I would think brass since the T fittings I have are brass.
Mike will they fit BMW 2002 units? This is my setup. I would like a set of those if they fit....
Attached image(s)
QUOTE (rick 918-S @ May 10 2005, 09:33 PM) |
Mike will they fit BMW 2002 units? This is my setup. I would like a set of those if they fit.... |
QUOTE (Aaron Cox @ May 10 2005, 08:39 PM) | ||
volvos are a tad bigger than the 2002 units. you could measure them |
for these volvo calipers are they the ATE or GIRLING types?
Whachya gonna do with that oval window?
QUOTE (Verruckt @ May 11 2005, 04:08 AM) |
Whachya gonna do with that oval window? :D |
QUOTE (rick 918-S @ May 11 2005, 07:01 AM) | ||
This summers project for the 15 yr old. Rat rod with a carb'd type IV. |
dan,
believe they are girlings......
see what AZ price youcan get
Mine are ATE, they are for the vented rotors, maybe the non vented are Girling.
QUOTE (skline @ May 11 2005, 10:51 AM) |
Mine are ATE, they are for the vented rotors, maybe the non vented are Girling. |
Girling for solid rotors are for 914 struts.
http://www.fcpgroton.com/volvo240brake.htm#calipers
scott/ron
which one for 3" spacing and vented rotors?
AND BTW- hawk racing makes pads for these calipers 50 bucks a set
QUOTE (Aaron Cox @ May 11 2005, 12:27 PM) |
scott/ron which one for 3" spacing and vented rotors? |
QUOTE (Aaron Cox @ May 11 2005, 09:50 AM) |
dan, believe they are girlings...... see what AZ price youcan get |
$60 for loaded and $30 for unloaded?
QUOTE (SLITS @ May 11 2005, 02:50 PM) |
$60 for loaded and $30 for unloaded? |
http://www.fcpgroton.com/volvo240brake.htm#calipers
Check the link above that was posted....$60 each loaded (yeh, they want a $25 core and shipping).
i will admit that's a better price, but the shipping of the cores wouldnt be so nice. i'd prefer having a lifetime warranty. http://www.autozone.com/servlet/UiBroker/?UseCase=C001&UserAction=answerRequiredQuestion&Parameters=%7C%7EWITH+SOLID+ROTOR&PageSync=5 and 20% employee discount
Well for the solid 914 rotor guys, they have brand new girlings for $69 and no cores.
BAH that stupid link didnt work...here's a screenshot
Attached image(s)
QUOTE (Travis Neff @ May 11 2005, 03:15 PM) |
Well for the solid 914 rotor guys, they have brand new girlings for $69 and no cores. |
FENCO (Fenwick) is a rebuilder out of Canada
ARI (American Remanufacturers, Inc..old ACEI) is out of Anaheim, CA.
QUOTE (SLITS @ May 11 2005, 03:43 PM) |
FENCO (Fenwick) is a rebuilder out of Canada ARI (American Remanufacturers, Inc..old ACEI) is out of Anaheim, CA. |
I'd prolly go with ARI (my apologies to the Canucks) based on business experience.
ARI down here does calipers, boosters and CVs. Their name (before acquisition) was Automotive Caliper Exchange, Inc (ACEI).
Fenco does everything in their Canadian location.
If you can afford new...get new!
rebuild kits for girling calipers are 23 bucks a pair...
im so stoked....
and ron. i have mcaliper 3" struts
QUOTE (dlo914 @ May 11 2005, 03:40 PM) | ||
where at? |
yummy.... HAWK performance pads (like 2x M caliper and stock 914 pad size)
for ATE calipers
http://www.buybrakes.com/store/HB172-595
Scott... will you take a picture of my windshield?
QUOTE (Eric_Shea @ May 11 2005, 07:41 PM) |
Scott... will you take a picture of my windshield? |
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)