These are the steering shaft bearings that also cross over to 911. We have actually been able to improve on the design some and these make a very nice fit. You can buy them on this GB when we are ready to ship (end of the week or so).
In purchasing this you also have the option to include the puck (
901.347.201.02, for $22
Hardware (including new washers - the ones that bend up as shown) for $8 more
2 elliptical washers ( 901.347.248.00) with 4 bolts as shown.
We are also working on the rubber that holds the bearing 901.347.223.03 that is NLA for $10.
You will only be able to get the special pricing on the add-ons if you buy the bearing at a greatly reduced price.
So.... Whos in?
Attached thumbnail(s)
Attached image(s)
I'm in for that! Lot of work but I'm tired of shaky wobbly steering.
I’m in for a couple. Thanks!
We are also adding some more racks back into inventory in the next week as we have gotten more parts back from plating. So we may be able to do the one stop shopping to swap it all out - for at least a few of ya.
I’m in for a Beardsley by
Thanks
I am in for one set
? What's involved to do this bearing replacement ?
Does this fix the metal scraping sound I hear when I turn my steering wheel sometimes?
I'm in.
In
I'm in.
in for the complete setup... just let me know when/how to order
In for bearing and seal.
I'm in for a complete set, thanks again !
i'm in for a set
I'm in for a set.
Jeff B
If we choose to include the rubber that holds the bearing, do you just ship the whole group when everything is ready?
I am in for two sets - this will also fit a 1972 911T right?
Bearings are actually done right now. We are just finishing up the rubber that houses the bearings and should have that ready within about 10 days. We also have a couple other items that are coming online to that of course you could consolidate with if you want.
perfect timing; I'm in for the bearing and bushing to go on the rack you just rebuilt for me
We will also clean up some of the shafts too, to make it all pretty (for those that like nice clean car parts. Will have them as an option, but in limited quantity.
I'm in for the bearing and hardware. Thank you.
In.
Why not: need some instruction though....
I've got the factory bearing in my parts stash and your rubber coupler but I'll need the rest of the hardware (minus the shaft) to refresh it all so I guess I'll be ordering the piece parts.
Just test for the rubber for the bushing from the prototype run.
Wiil be starting the GB up like this week. Just need to know who's in so I can send PM's with the codes
In for both, please
I am in for a set. Let me know how to pay.
Thx
We will be sending discount codes to all that bump the thread here shortly.
I'm in..
Codes sent out to all thus far.
Link to listing
http://shop.914rubber.com/searchquick-submit.sc?keywords=901.347.2414.01
This ends today 11/15/17 and we are just finishing up the rubber run so they will be shipping shortly
I am in for one full set
I'd like to get a full set also.
Mark, I'm down for a full set.
PM's sent
I can't do maths. How much for the set?
Thanks
Brett
Went out and yanked this off my shaft. All wrapped up in rubber like that, I can't imagine this thing ever wears out. Mine is gummed up a little from the old rubber but has no play in it. Seems like the real gem of this set is not PN 26, but PN 22 and 30. Sign me up!
Base on your initial post, $22 for the bearing, $10 for the rubber bushing, $8 for the hardware comes to $40... PN 22 is circled in the diagram but not sure where it fits in the price scheme?
I just ordered a set. thanks!
I’m in for a set please!
Thank you!
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)