Good Morning,
Yesterday was supposed to be the day Mike drives off in his freshen up 72 daily driver.
Didn't quit go as planned ................ I finished the shift rod install before lunch. Then he and his right hand man, O'Ryan went about installing the hoods. Then it was time to dial in the shift linkage adjustment. Set about using what I call the Chris Neutral adjustment. Has work flawlessly for a long time. Not This Time.
Looks like Chris might have been converted to the 4th gear club.
After more time I want to admit (or charge for) we couldn't get it to completely shift into the 1-3-5 plane. Pulling my hair out ............... this isn't supposed to be that tough. Long story short. Finally determine its not the linkage adjustment. I have a nice and tidy neutral. Can feel all gears. Just won't stay in lower plane. So we finally pull off the shift cover. Remove the shift rod. Then go about shifting the gear box by hand. Still no lower/back plane. Gear box is toast.
Mike is amendment it worked great when he drove it in San Diego and when he drove it up here years ago.
So I grab the ball pin and watch it turn. Guess what. The ball pin is turning and not the shift rod. That don't look right. So I go over and check other gear boxes standing in the corner. No Play. Hmmmmmmmmmmmmm. I did have a coil pin, not just a roll pin.
Shifted great last time I drove it : New Data Points
If you have boxes in the corner, remove a shift console and swap it out. This will require draining the oil.
I'm not a tranny guy. I've got people for that ......... LOL
That was one of my first thoughts. But it looks like the shaft is pinned again inside the box. Or does that whole thing slide in and out ?
Part 14 at the top of the shaft is a critical component, also subject to wear that exacerbates sloppy shifting. New ones from Porsche are pricey.
The shape of the "comb" is important to smooth transition from one gear to another.
Ok ............. you've perked my interest/curiosity.
Not going to touch the one that my boys call my best shifting box. But I have a side shifter I got in a Montana garage clean out. It will be my victim.
Mark probably wouldn't like me stealing the one out of his project car box. LOL.
I assume neutral in and out ?
I'll stop at Ace from some roll pins too.
Swapping consoles, while not difficult, is messy and does take time. And, when done you'll be left with a good shifting trans in the car and an incomplete trans on the shop floor. If you want to reassemble the one on the floor you're going to need to deal with the old console. Why not just ream for the next larger roll pin withe the console still in the car? If I recall correctly there should be enough room. Ultimately less time and less mess than the path you're pursuing and you don't run the risk of introducing new oil leaks.
What size should the hole be reamed out to and what size coil pin replacement?
Classic engineering answer: it depends.
Search Google for "coiled spring pin" and there are numerous manufacturers that give hole size based on the size of the pin you're using. The OP shouldn't need to enlarge the hole much beyond the original size. What the final hole size will be is dependent on how enlarged the current one is and what size coil pins are available to him.
Hmmmm
On the way out to the shop I stopped for some coil pins. No luck just roll pins.
Both 1/4 and 6mm.
First Data point in my head. The PET calls outs a 6 * 32 roll pin. The coil pin the came out was 5.79xx and really worn in the middle.
The roll pins I bought had on OD of 6.02mm. I enlarged the hole in the ball with a 15/64 drill bit. 5.9531mm.
Hole started at 5.831. Not too much but the new 6mm wouldn't start. After running the drill thru there the new roll pin fit nicely, though a little short. They only had 30mm. So I installed it back on the transmission and gave it a go. Thus time I couldn't see any movement with the naked eye. Installed the shift rod back on, time for a test. The lower plane shifts feel a little better. So I give it the test. Will it stay in gear ?
Start the car in 3rd. Pops right out. Start the car in 5th. Pops right out. Time for a time out. Short day, heading to a birthday dinner ............
But I pull down the spare gearbox and start draining the oil. Only to find out its stuck in 4th gear.
The battery in my micrometer was giving me issues so a little shy on numbers.
Here's the info on coil pins.
https://www.spirol.com/library/sub_catalogs/cldp-Standard_Coiled_Pins_us.pdf
Also, recheck shift alignment. If your stick cannot transition far enough aft then you will see issue with 1/3/5. If you adjust your stick to give some more travel to the aft (as noted on the shifter at the transmission), this may solve your problem.
As for the other box stuck in 4th, not a big deal. Drive out the roll pin that you are now intimately familiar with, pull the console housing while leaving the console rod and shift comb in the box. Then, once the console is clear, just wiggle the rod/comb out of the hole. You can then shift the box into neutral using a screw driver.
Ed reminded me that we've seen that ball end welded to the shaft at least once before.
I took the tightest one from the Rothsport collection. Plus the loose rod and hardware.
Than ran the old MiddleMotors spare thru the jet washer a few times to get it cleaned up.
Then went ahead and pulled the bearing bracket without the rod from the spare. Once the bracket was out of the way, the rod came right out. Into the jet washer they went.
Just like Doc said.
Seals and pins are inbound.
Then went ahead and drained the Swepco out of Mike's gear box.
So here's where we're at :
Wednesday night Mike and I had a moonlighting session using a tighter pin from the Rothsport stash. I adjust the linkage so I have the longest rearward shift I can get.
Still the same. Won't actually shift into 1-3-5. I can hold it in gear pulled back on the shifter. But not really engaged.
So I unbolt the all the linkage and move it out of the way. Now I attempt to shift into 1-3-5 by hand. No go ............. Just wont go in. We're done for tonight, lets go home.
So last night after I drain out the Swepco I can shift into 1-3-5 without an issue ...
The only other tidbit to add. Gordon Ledbetter stopped by Rothsport on Monday and I ran my issues past him. Without seeing and feeling it he didn't have much to go on. But he did say both pins have to be tight with zero play. And you need both the upper and lower washer. Upper washer is NLA. Lower available used. I don't think any of the shift rods have the upper washer on them.
Without the engine running, it can be difficult to engage gears sometimes. Was this tranny recently worked on? Did you install a gasket between the shift console and the case? There shouldn't be one. It is sealed by an O-ring
With the console removed you can move each selector rod into gear by levering with a big-ass screwdriver/prybar.
You can also verify that the spacing/alignment of the selector rods is correct if you have the specs from the workshop manual.
Those washers are missing on most of the shifter consoles and are not actually critical to the operation of the part. They serve to keep wear of metal on metal down to a minimum, but there is not all that much wear. The comb will align with the rods irrespective of the washers presence.
Yes, make sure no paper gasket is there (only the O ring). It is a tail shift/nose shift part and can mess up shifting with a side shift console.
I also wonder if work was done recently and the rods were not adjusted correctly. Chris has the right next step, try shifting them with a screwdriver or bar from the hole.
Sometimes it is a pain to shift into gear with it not running or if it hasn't been lubed by being run after someone was in it.
The fact that you can shift once the Swepco is drained is odd. That would indicate that your synchro bands are not able to exert enough force on the slider to keep it locked in and it is too slick causing it to pop out. Like trying to hold a greasy pig.
I think Mike's owned the car 10 years. Daily driver in San Diego 5 years ago. Been on jack stands the 5 years its been in PDX. Who knows. Tried it with dyno gear lube. No go.
Swapping out the gear box from my project car. We have it about ready to drop on the table. Mike's thinking he'll take a swing it rebuilding.
Now me I'm thinking I'll start begging for a Dr. Evil rebuild clinic here at MiddleMotors.
Starting List :
Cary
Super In Law (Jack)
Mark Whitesell
Matt Whitesell
Mike Warhurst
Taylor Whitesell
Maybe we can use the McMenamins Grand Lodge for our out of town guests.
I have your DVD and written word all set to go for Mike ............
Update : We ended Saturday just about ready to reinstall. (AX Annual Tech for the Carrera in the am) While we had it out , again. It got a new alternator harness. Its going to get a new ignition harness too, but I'll need to do a conversion to a 72 today. Sorry to say the heater wires will have ride on the outside. But they'll be new and fresh.
Hopefully 10 years hasn't jinxed my spare gear box and Mike will be driving home tomorrow. He's talking about taking it down to Route 66. That would give him a some time with the dye kit in the engine oil to help us (me) find the oil leak(s). Filter was about a 1/4 to 1/3 turn loose, hopefully that was it.
On his way home .................... with his borrowed gear box.
Hit the linkage adjustment dead on first shot. Chris bungee cord in neutral
He'll be back this afternoon to box up his spare parts. I'm going to tune his window frame so they fit tight to the windshield frame. Clutch needs some adjustment. Jacked out and to the left. Goofy ............ While the pedal cover is off I'll set the brake pedal free play to spec. Then we'll see if he wants a little tune on the pedal free play.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)