Printable Version of Topic

Click here to view this topic in its original format

914World.com _ 914World Garage _ Fenders, Fenders, Fenders

Posted by: pastordavid Jun 19 2005, 05:45 PM

OK, here is the new guy with a problem. I finally talked my father -in-law out of his 72 914 that has sat behind his house for the past 20 years, waitng for him to "fix it up." The good news is that the price was right (free) and he even delivered it! The bad news is...well, you can see the bad news. In 83, he had it sold, and the night before the guy was supposed to pick it up some kids broke into it and rolled it down the hill in front of his house into a brick wall. So now the question - any sources for fenders out there? Any suggestions for mods? Thanks!

David

Attached image(s)

Posted by: SirAndy Jun 19 2005, 06:02 PM

the usual places first ...

http://www.easypor.com/, http://www.highperformancehouse.com/ and http://www.PartsHeaven.com/

or maybe one of the members here can help you out ...
Andy

PS: welcome to the club!

Posted by: jimkelly Jun 19 2005, 06:14 PM

I'm curious - post some more pic when you got them.

May be buy a parts car

www.thesamba.com

www.ebay.com

as it looks like you'll need more than just a fender.

Jim

Posted by: Headrage Jun 19 2005, 06:17 PM

Drive to California. I'll give you whatever you can cut off.

Posted by: McMark Jun 20 2005, 02:19 AM

That's a serious project. You need a fender and an inner wheelwell and a headlight bucket. That whole corner of the car.

Posted by: Jeroen Jun 20 2005, 02:50 AM

keep an eye out on members sawzalling their "junkers" here
that would be the easiest/cheapest way to get a new corner for your project

Posted by: Jakester Jun 20 2005, 09:43 AM

I recently went through a similar path that is ahead of you.

Check out my initial http://www.914world.com/bbs2/index.php?act=ST&f=2&t=31948&st=0.

You definately need to be handy with a cutting torch or sawzall and have the ability to do some intricate body work and welding.

Previous post is right - that is a serious project. You only learn by doing, however, so.... ............

Good luck!

Posted by: Mueller Jun 20 2005, 12:10 PM

have you pulled the carpet and inspected the floors??

what about the section below the battery and behind the rocker panels??

from the looks of the rust on that section, I'm willing to bet you have a rusty chassis that is not worth fixing up....I could be wrong and hope I am, but you should be worried about the structual strength of the rest of the car first.....

Posted by: pastordavid Jun 20 2005, 12:26 PM

Jakester, thanks for pointing me to your thread. I have been tearing things apart in prep for a ground up overhaul, and was really getting discouraged, but after looking at what you have accomplished, I have a whole lot better outlook. Now if I could just figure out how to get those seats out...

David

Posted by: pastordavid Jun 20 2005, 12:36 PM

Mueller,
Yes, the first thing I did was pull the carpets (LOTS of mold there!) and surpisingly the floors, longs, and general area was fine. I did the "Fat Dave" test as well, and no flex. The battery tray is rusty, but not rusted. The worst rust (other than the crunched front end) is the tail light area, the door handles (extterior) on the rear quarter section, and the aprons along the sides under the doors. Otherwise, I think it is pretty good. I'll know more when I get the rest of the "stuff" out of the way. I am heading out on vacation on Friday, hoping to have everything pulled but the drivetrain, which will have to wait until I get back.

Luckily, I worked for 15 years as a mechanic, before going into the ministry, and my son-in-law is a body man, and my best friend is a custom metal fabricator. Now what about those fender flares from John...

I'll post a few more pics later.

Blessings to all,
David ?