Whats the going rate for a usable 1.8 AFM (0 280 200 012) as the one I have is toast ?,not worried about cleaning and servicing.
I have an good early 1.7 shortblock and have heads and 96mm B&P set to fit but will need to purchase injectors also,in real terms the case is worth very little with the cam it has and think this may be a good move for my situation,I don't know if the D-jet cam plays well with L-jet cam?,believe they do.
I have sold most of my D-jet stuff now and also prefer the less complicated system with L-jet and besides I have bugger all knowledge of D-jet besides.
TIA .
All the 914 4cyl engines used essentially the same camshafts.
The part numbers listed in PET are only different for the cam gear variances.
The 1.8 injectors are big enough for a 1.7 with 96mm pistons.
So you should be good to go with the 1.8 L-jet injection.
Jim
If your in Oregon, Try Craig at Camp 914 I know he has a pretty good stash of parts. I can check as I may have some 1.8 stuff. I do have a 912E with a running fuel injection system and it's great. Really the way these cars would have went if they continued production.
Dragged the case out and checked it out ,all good ,cam and lifters good...that was my main concern as don't want to split the case,test assembled the engine with old parts today, injection system on and went though the "where is this part fit" deal .
Enjoyed test fitting it together and know it will be a good engine,but need to confess it will be a bus engine just for resale and think someone will get good use from it.
Will report further cheers.
Cleaned up the case and doing a refit of the rods with new standard KS big end bearings,these are the same part number (standard size) shells that I removed,my question is how tight should they be on the crank journals,side clearance appears ok but they seem a little loose,please fire some idea's my way as I don't remember way back when I did my last T4.
Deck clearance checked @ just over 1mm so happy enough with that,I still need to check further as my pistons are high compression and I can't find my chamber measuring gear .
TIA.
Think I have my connecting rods sorted,usual PO issues ,dizzy drive 180 degrees out,and found the rear main seal glued in with sealer as per the front seal,RMS was proud of case and running hard on the flywheel most of the face worn off ,well atleast the flywheel is good .
Flywheel bolts done @ several different torques and used chewed up washer ,end float checked ok before removal however.
Need another torque wrench as none of mine will not do the lower settings required ...too large or too small ,just my luck .
Going pretty well so far,will post some pics soon.
Case cleaning has taken way longer than I thought between other work but it is clean now,JB welded the oil gallery plugs ,most likely not needed but wanted to be sure ,due to poorly fitted RMS seal there was a small leak , have been checking end float,came out @ .0032 so happy with that.
Case has been split before but some fine individual has been very excessive with gasket shellac and caused BS to get rid of it @ front and rear crank seals recess's.
Not 100% happy with piston pin fit so will get the rods rebushed,hooked up with a local engine shop and have found new bushes in my country.
Heads are a bit of a guess really,fully rebuilt but part number 022 102 372G comes out @ 2.0 bus ,understand they are low compression but fit my 1800 barrels so something is odd.
Attached thumbnail(s)
Rechecked deck height again and came up with 0.028 instead of my original half arse attempt ,won't order shims until heads are measured for volume.
I have mothballed the L-jet motor as this (carb) motor is more complete and I have a guy that wants to buy it for a repop 550 Spyder.
Heads still remain a mistery as the number keeps coming back as 2.0 bus ?,these were flycut to 105mm (93mm) barrels,intake ,exhaust valves are larger than these heads were supplied with also.
Partially stripped one head to find the reconditioning on these to be a very high standard,guess it matters little what they are off as the condition is exceptional.
More to follow,cheers.
Placed base shims under the barrels and came up slightly over 1mm deck clearance with high comp pistons that gives me around 8.1.1 allowing for piston dome, jeez I have checked that many times .
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)