Posted by: Sm914650 Jul 21 2019, 06:51 AM
Seat***
Have some normal rips where bolster corners off on both seats. Thinking of ordering the bolsters from 914rubber. Anyone have any experience installing these? Wondering what the process is, and whether I need to reupholster them to the seat or just fit them in. Havnt been able to get an answer as of yet.
Posted by: mepstein Jul 21 2019, 07:44 AM
I did them a couple months ago. Good product. I used weldwood contact cement and a heat gun. It takes longer than you expect but came out nice.
Attached thumbnail(s)
Attached image(s)
Posted by: bbrock Jul 21 2019, 08:17 AM
http://www.914world.com/bbs2/index.php?s=&showtopic=71844&view=findpost&p=900796
I have a few additional details from my experience starting here
http://www.914world.com/bbs2/index.php?s=&showtopic=307290&view=findpost&p=2684884
Posted by: 914werke Jul 21 2019, 09:00 AM
what about the match to the OE vinyl grain /pattern?
Posted by: mepstein Jul 21 2019, 10:48 AM
QUOTE(914werke @ Jul 21 2019, 11:00 AM)
what about the match to the OE vinyl grain /pattern?
Very close. A little smoother and shinier.
Posted by: cuddy_k Jul 21 2019, 11:28 AM
The biggest differerence is that OEM is thicker. The slightly thinner gauge of the 914Rubber material means you need to pay a little more attention to the smoothness of the foam underneath, and how it wraps around the back of the headrest. I ended up using 1/8 inch closed foam on top of the existing, and used an upholstery needle and thread to tighten the headrest area up.
I did my driver's side (which was ripped) and didn't end up needing to do the passenger side (which was perfect) since the match was so close. No one has ever noticed...
Posted by: 914werke Jul 22 2019, 11:26 AM
QUOTE(cuddy_k @ Jul 21 2019, 10:28 AM)
The biggest differerence is that OEM is thicker. I did my driver's side (which was ripped) and didn't end up needing to do the passenger side (which was perfect) since the match was so close. No one has ever noticed...
I thought it was single piece already sewn together? both bolsters & back
Posted by: mepstein Jul 22 2019, 12:04 PM
QUOTE(914werke @ Jul 22 2019, 01:26 PM)
QUOTE(cuddy_k @ Jul 21 2019, 10:28 AM)
The biggest differerence is that OEM is thicker. I did my driver's side (which was ripped) and didn't end up needing to do the passenger side (which was perfect) since the match was so close. No one has ever noticed...
I thought it was single piece already sewn together? both bolsters & back
It is. I think he was talking driver seat/passenger seat.
The big thing I learned with upholstery is it takes time. Prep, glue drying and the little details. Don't say, I'm going to do it this weekend, Say, I'll keep working on it until it's done.
Posted by: cuddy_k Jul 22 2019, 03:02 PM
QUOTE(914werke @ Jul 22 2019, 01:26 PM)
QUOTE(cuddy_k @ Jul 21 2019, 10:28 AM)
The biggest differerence is that OEM is thicker. I did my driver's side (which was ripped) and didn't end up needing to do the passenger side (which was perfect) since the match was so close. No one has ever noticed...
I thought it was single piece already sewn together? both bolsters & back
Yep. The bolsters and back are one piece. I was just saying that because the material is thinner, it needs a little more finessing than OEM. After nearly 50 years, the lower bolsters on mine definitely needed additional foam to fill out the new cover.
I also agree with Mark. Definitely doable as a DIY, but you need time.
Posted by: mepstein Jul 22 2019, 03:23 PM
QUOTE(cuddy_k @ Jul 22 2019, 05:02 PM)
QUOTE(914werke @ Jul 22 2019, 01:26 PM)
QUOTE(cuddy_k @ Jul 21 2019, 10:28 AM)
The biggest differerence is that OEM is thicker. I did my driver's side (which was ripped) and didn't end up needing to do the passenger side (which was perfect) since the match was so close. No one has ever noticed...
I thought it was single piece already sewn together? both bolsters & back
Yep. The bolsters and back are one piece. I was just saying that because the material is thinner, it needs a little more finessing than OEM. After nearly 50 years, the lower bolsters on mine definitely needed additional foam to fill out the new cover.
I also agree with Mark. Definitely doable as a DIY, but you need time.
I didn't need more foam but I did heat up the vinyl and do a lot of stretching.