Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ Anyone replaced their tail/crossbody?
Posted by: jaredmcginness Jul 16 2020, 08:48 AM
Hey guys,
Next on my list for body work that I've been putting off.
Tail section. I'm having a hard time finding any threads on the subject. I remember reading one with a red car. Lots of sandwich and layered pieces.
Has anyone tackled this, any tips/photos?
Cheers
Posted by: peteyd Jul 16 2020, 09:30 AM
@http://www.914world.com/bbs2/index.php?showuser=439
I believe Perry has installed one.
Pete
Posted by: SirAndy Jul 16 2020, 10:13 AM
That was probably mine, did that many, many years ago.
There should be a thread here somewhere ...
Posted by: 9146C Jul 16 2020, 10:17 AM
I did a "spliced" repair as I didn't want to mess with the driver's side tow pull bracket (there was no corrosion in this area on my car).
The RD panel I bought was a perfect fit to OEM.
The only "issue" I had was getting a good rosette weld on the rolled lip of the trunk pan (which was also replaced)...I wound up through drilling the pan to cross panel seam.
If you look closely at the photos (in my thread) of the left sail panel repair, you'll get a glimpse of the 2x4 I cut to maintain the trunk width before sizing the new panel. Now that the work is complete and I've temporarily fit the rear deck lid, the gaps looks good front to back on both sides. (I don't recall the cross dimension, but it can be found on the dimension specs of this forum.)
http://www.914world.com/bbs2/index.php?showtopic=342108&st=20
Posted by: Root_Werks Jul 16 2020, 10:18 AM
I might need to do this to my 914. Rear lid is bent, have a replacement and will see how things line up.
Doesn't look easy.
Posted by: jaredmcginness Jul 16 2020, 10:52 AM
Thanks for the good replies guys.
The splicing is not a bad idea, if it the edges are in good shape. I dont think mine are...
I suppose one of my questions was the dimensions. Seeing if anyone has braced the opening to keep it dead on.
I'll try to look through your post history Andy. 
Posted by: 9146C Jul 16 2020, 10:57 AM
http://www.914world.com/specs/bodydims.php
These were the dimensions I used...it is the same for the full width of the trunk...I was able to brace mine with a 2x4 as it had a natural tendancy to want to spring inboard.
Good luck!
Posted by: Mikey914 Jul 16 2020, 11:49 AM
@http://www.914world.com/bbs2/index.php?showuser=1608 has done 2 of mine. There is an early late issue
You have to modify floor for late.
Posted by: dr914@autoatlanta.com Jul 16 2020, 12:29 PM
many times, you must salvage pieces from your old rear panel to make this one work. Also the wurth gun with the correct calking it will apply the sealer to the joint in a factory type way. Make sure that your unibody is pulled out straight before installing the rear panel or the rear lid will not fit and the quarter panels will be slightly flared out
Hey guys,
Next on my list for body work that I've been putting off.
Tail section. I'm having a hard time finding any threads on the subject. I remember reading one with a red car. Lots of sandwich and layered pieces.
Has anyone tackled this, any tips/photos?
Cheers
Posted by: IronHillRestorations Jul 16 2020, 12:54 PM
Although more difficult and involved, replacing the whole panel is probably the best way to go.
The radius on a couple 90* bends is different than stock, so doing a section is going to require some extra "massage to fit", if you choose to go that route.
I cut the top off narrower than the bottom, within the tail light openings, but if I were doing it again, I would indeed replace the whole piece.
Posted by: bkrantz Jul 16 2020, 09:54 PM
I removed and re-installed the rear panel (which was not the original).
One challenge is the seams with the fenders. These are actually triple layer, with the flanges on the rear panel sandwiched between the inner and outer fender edges.
Posted by: jaredmcginness Jul 17 2020, 07:00 AM
I removed and re-installed the rear panel (which was not the original).
One challenge is the seams with the fenders. These are actually triple layer, with the flanges on the rear panel sandwiched between the inner and outer fender edges.
Sounds good. I just ordered the replacement.
Edit: Nevermind, found on page 3 and 28. Helpful photos to get a better idea of what i'm dealing with.
Posted by: cary Jul 17 2020, 07:49 AM
I've done 3.
I have another ready to go on another onsite project.
What George and Bkrantz said. The qtrs have to be pulled out a smidgen to get that triple layer section
at the taillight slid in.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)