I've looked at the Weber Service Manual kindly scanned for us.
Can the check/adjustment be done without the special tools listed in the manual? If so, how?
-Rusty
yes
i have the haynes weber manual and it says to use a rubber wedge to hold the float and venier calipers and a feeler gauge for the mesuarments.
that's how i dunit.
doug
Was the adjustment fairly easy?
Do you know about how to check the floats for servicability?
I'm concerned about reasons why my carbs might be overflowing. Checking the needle valves are next on the list. I cleaned them once before.. but I'm going to check them after the floats.
-Rusty
did your bowls just start overflowing?
has it been running?
how do you know they are overflowing?
leaking fuel somewhere?
if the floats are leaking, you should be able to shake them and feel the fuel in them.
yeah it was easy, a little tedious. you want to check and recheck you measurements.
Yes, it was running. But, I had a problem of fuel hydrolock of the engine. Now that I've fixed other issues, now I'm looking for the root problem of the hydrolock.
-Rusty
hhmm .... "i think" .... overflowing bowls can be sticking needle valves, sinking or sticking flaots or too much fuel pressure.
do you know your pressure?
if it has been running fine. the float levels are probably good.
Dude,
The measurement the manual lists is only approximate. It will get you running, but it won't get the float levels to the correct setting all by itself. BTDT You really need to follow up with the gauge that screws into the sides of the float bowls.
Call my cell tomorrow.
I purchased the float gauge tool.
Using it was a pain.
When the engine was running, the float level 'jumped' due to vibration.
A lot of fuel is wasted due to having to drain each float chamber to screw it in, and to add washers under the float valve.
There also is some 'surface tension' on the fuel so the height is difficult to judge accurately.
Mine seem to be about right now (only one needed a washer to raise the valve), but I remain to be convinced about this method.
Attached image(s)
My gut instinct tells me that the issue isn't the float adjustment (it's been running fine for 2-3 years without tampering with it). However, I've got to pull them to check to see if they're leaking inside, so I might as well adjust the height.
I use the gauge in the pic.
I set the floats with the carbs off the engine....static, with the carb in a pan to catch the gas. A few "special tools" were necessary to fill each float bowl......backyard engineering....a turkey baster for one
A bit of experimenting with shims under the needle valves to learn how much each effects the float height.
Another PITA, but part of the learnng curve.
Why did you fill the float bowls to set their height?
Anything special about the shims? Something I should buy locally, buy from PMO or make myself?
Nothing is ever easy.
Hey Mike,
When doing the float level adjustment - why have gas in the carb?
-Rusty
The gauge in the pic attaches to the port in the side of the float bowl. It fills with gas. The level of the gas is between the upper 2 lines on the gauge when the floats
are set properly. Using the static method, I set the level at the 2nd line from the top ...Kentucky windage for the lack of pressure...seems to work.
Setting the floats is prolly the most important part of dialing in Webers so's they neither flood nor lean out
durring hard cornering.
Shims come with the rebuild kits....never throw any away.....I have a pee pot full of them in both copper and ....composition.
ohhh shezzzz ..... yeah, you definitly need the float level gauge!! sorry .... i took a quick glance at the manual you were referring to and i only saw the spring to hold the float and the special gauge for the float.
if you are taking the tops off, you should get the rebuild kits. it's easy to tear the top gasket. plus you get all the shims and other washers. you probably know this, but be careful with those needle valve caps. they are soft and you can muck them up, ask me how i know. it's best to loosen them while the carbs are on the car. but pmo sells new ones.
good luck,
doug
Rusty,
Your problem sounds like one I had with over flowing carbs. What you are attempting is what I tried and didn't help until I began to think about the whole system operation. To make a long story short, I loosened the gas cap to allow it to breathe. Clamped off the fuel line to the carbs at the pump. Turned the ignition to on. and listened for all the air bubbles coming back to the tank by way of the return lines. IE; Air block in the return line while the tank is pressurized. The pump is pushing through the line with least resistance. Once the lines between the tank and the pump are fully primed, the pump is rotating the gas between the tank and itself.
Try that. Then think about how the entire system works. Worked for me.
Don
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)