Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ how do I get this out?
Posted by: hndyhrr Nov 7 2021, 06:10 PM
I am taking out the dash. How do I get this undone? See pic.
Attached thumbnail(s)
Posted by: hndyhrr Nov 7 2021, 06:14 PM
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM) 
I am taking out the dash. How do I get this undone? See pic.
here it is from the inside
Attached thumbnail(s)
Posted by: partwerks Nov 7 2021, 06:16 PM
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
Posted by: hndyhrr Nov 7 2021, 06:19 PM
QUOTE(partwerks @ Nov 7 2021, 04:16 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
tried to slide but would not budge, perhaps some gentle persuasion?
Posted by: partwerks Nov 7 2021, 06:24 PM
QUOTE(hndyhrr @ Nov 7 2021, 04:19 PM)
QUOTE(partwerks @ Nov 7 2021, 04:16 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
tried to slide but would not budge, perhaps some gentle persuasion?
Try warming it up a bit with a heat gun to see if that helps it to slide?
Posted by: hndyhrr Nov 7 2021, 07:45 PM
got it out, one more thing albeit little is done.!
Posted by: partwerks Nov 7 2021, 07:49 PM
QUOTE(partwerks @ Nov 7 2021, 04:24 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:19 PM)
QUOTE(partwerks @ Nov 7 2021, 04:16 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
tried to slide but would not budge, perhaps some gentle persuasion?
Try warming it up a bit with a heat gun to see if that helps it to slide?
Can't see the back side, but doesn't appear there are slots on the back side, so maybe slide it to the left, and then poke the back of it through first, and then those tabs might slip up into those slots??
Posted by: hndyhrr Nov 7 2021, 08:29 PM
QUOTE(partwerks @ Nov 7 2021, 05:49 PM)
QUOTE(partwerks @ Nov 7 2021, 04:24 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:19 PM)
QUOTE(partwerks @ Nov 7 2021, 04:16 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
tried to slide but would not budge, perhaps some gentle persuasion?
Try warming it up a bit with a heat gun to see if that helps it to slide?
Can't see the back side, but doesn't appear there are slots on the back side, so maybe slide it to the left, and then poke the back of it through first, and then those tabs might slip up into those slots??
it did slide to the left and then just jumped right up and out. don't have heat gun used very gentle leftward persuasion.
Posted by: partwerks Nov 7 2021, 08:30 PM
QUOTE(hndyhrr @ Nov 7 2021, 06:29 PM)
QUOTE(partwerks @ Nov 7 2021, 05:49 PM)
QUOTE(partwerks @ Nov 7 2021, 04:24 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:19 PM)
QUOTE(partwerks @ Nov 7 2021, 04:16 PM)
QUOTE(hndyhrr @ Nov 7 2021, 04:10 PM)
I am taking out the dash. How do I get this undone? See pic.
It almost looks like you would slide it to the left, and push back up through??
tried to slide but would not budge, perhaps some gentle persuasion?
Try warming it up a bit with a heat gun to see if that helps it to slide?
Can't see the back side, but doesn't appear there are slots on the back side, so maybe slide it to the left, and then poke the back of it through first, and then those tabs might slip up into those slots??
it did slide to the left and then just jumped right up and out. don't have heat gun used very gentle leftward persuasion.
Good job!
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)