Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ Front trunk inner seal causing trunk to "bow"
Posted by: Root_Werks Mar 17 2022, 03:27 PM
Front trunk aligns and closes with good gaps. Install the main outer seal, still good. Install the seal between fuel tank area and spare tire area and the trunk will bow.
I pulled the inner seal out for now. Used a scope camera and can see what looks like a pretty even 1/4" gap with inner seal removed. Use the camera again with inner seal installed and I can see the trunk rest down on the seal, but not compress it enough.
It's a 914Rubber seal. Same front to back, rear trunk seal seems just fine.
Any experience with this? Anyone?
Posted by: Steve Mar 17 2022, 03:53 PM
QUOTE(Root_Werks @ Mar 17 2022, 02:27 PM) 
Front trunk aligns and closes with good gaps. Install the main outer seal, still good. Install the seal between fuel tank area and spare tire area and the trunk will bow.
I pulled the inner seal out for now. Used a scope camera and can see what looks like a pretty even 1/4" gap with inner seal removed. Use the camera again with inner seal installed and I can see the trunk rest down on the seal, but not compress it enough.
It's a 914Rubber seal. Same front to back, rear trunk seal seems just fine.
Any experience with this? Anyone?
It’s a known problem. The stock seal is lower and doesn’t cause the trunk lid to bow.
Posted by: sholman5 Mar 17 2022, 03:59 PM
QUOTE(Root_Werks @ Mar 17 2022, 04:27 PM)
Front trunk aligns and closes with good gaps. Install the main outer seal, still good. Install the seal between fuel tank area and spare tire area and the trunk will bow.
I pulled the inner seal out for now. Used a scope camera and can see what looks like a pretty even 1/4" gap with inner seal removed. Use the camera again with inner seal installed and I can see the trunk rest down on the seal, but not compress it enough.
It's a 914Rubber seal. Same front to back, rear trunk seal seems just fine.
Any experience with this? Anyone?
I had the same problem. Pull the seal off and put the right side on the left and left on the right. Basically it is on backwards. Worked for me.
Posted by: 914Mels Mar 17 2022, 05:03 PM
QUOTE(Root_Werks @ Mar 17 2022, 01:27 PM)
Front trunk aligns and closes with good gaps. Install the main outer seal, still good. Install the seal between fuel tank area and spare tire area and the trunk will bow.
I pulled the inner seal out for now. Used a scope camera and can see what looks like a pretty even 1/4" gap with inner seal removed. Use the camera again with inner seal installed and I can see the trunk rest down on the seal, but not compress it enough.
It's a 914Rubber seal. Same front to back, rear trunk seal seems just fine.
Any experience with this? Anyone?
Noticed the front hood was sitting higher after putting in the new 914 rubber seal. Tried it both ways in the channel but it's too tall. put it in a couple months ago but it's not compressing. For now I just pulled it out, I might try to modify it but not sure short of cutting the flap part of what could be done. The front edge fits fine on the bumper.
Posted by: Root_Werks Mar 17 2022, 05:32 PM
QUOTE(914Mels @ Mar 17 2022, 04:03 PM)
QUOTE(Root_Werks @ Mar 17 2022, 01:27 PM)
Front trunk aligns and closes with good gaps. Install the main outer seal, still good. Install the seal between fuel tank area and spare tire area and the trunk will bow.
I pulled the inner seal out for now. Used a scope camera and can see what looks like a pretty even 1/4" gap with inner seal removed. Use the camera again with inner seal installed and I can see the trunk rest down on the seal, but not compress it enough.
It's a 914Rubber seal. Same front to back, rear trunk seal seems just fine.
Any experience with this? Anyone?
Noticed the front hood was sitting higher after putting in the new 914 rubber seal. Tried it both ways in the channel but it's too tall. put it in a couple months ago but it's not compressing. For now I just pulled it out, I might try to modify it but not sure short of cutting the flap part of what could be done. The front edge fits fine on the bumper.
Yup, same here, might wind up getting a universal seal that's softer and shorter or more shallow.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)