...I bought from my original owner Dad in 2002 with 41K mi. and have been driving it since, now with 58K miles. It has been to 5 Okteenerfests among other events, and some members here have seen this very clean car. I'm wondering what remains of near 50 yr. old lubricants, and what should I be most concerned about replacing? I've replaced shocks/springs, injectors/ and other necessary items, but now am thinking about old lube in CVs, bearings, and other rolling parts. I can do most maintenance wrenching, but hate to disturb working systems, if it ain't broke should I fix it. What should be the priorities here?
First reaction is to leave well enough alone and enjoy.
Great example
Not many of these around
Keep fluids (engine oil & trans lube) changed on regular interval and keep valves adjusted.
Brake Fluid is you biggest contamination from time perspective. Brake fluid is constantly absorbing environmental moisture even through that tiny vent hole in the reservoir cap. I'd replace it with a complete flush every 3-4 years.
I wouldn't sweat the grease too much. Over time it tends to get hard/waxy and loses lubricity. If you haven't run into issues in the last 16K miles you're not likely to have failure now so not a high priority action item. Rear wheel bearings are sealed for life and when they begin to fail you'll know it and will get plenty of advance warning. Front wheel bearings are a regular maintenance item (adjust & lube).
For the rest of the components. . . deal with as needed. Drive & enjoy!
Really the only thing "necessary" is to replace the original plastic fuel lines and any old rubber fuel lines in the engine compartment. Preventing a fire is paramount in our old cars.
Yay!
My plastic fuel lines are still soft & flexible. The car is a "73 with 48K miles. Go figure. Did Porsche use different materials for these lines depending upon the logistics & timing of the assembly process?
BTW, I did replace the "rubber" tubing at the gas tank, fuel pump, & fuel injectors (IIRC). I also replaced the fuel pump & it's rubber mounts. That was a PITA since this really takes two people, but I managed to do it solo. It would have been much easier if my arms were twice as long. I hate working with gasoline. BTW, sweet car!!!
@http://www.914world.com/bbs2/index.php?showuser=8476 .
no - re materials on fuel lines. from 70-74. all used same clear plastic with a stainless steel end up near the tank.
factory changed them when they shifted fuel pump to front to a high pressure fuel hose material.
you would be unusual in having still flexible lines all the way from the tank to the pump if the pump is still in the area under the engine bay.
i have a car, of similar mileage to you and which didn't do much for 16 of the last 18 years. the lines where they emerge from the tunnel and travel across the passenger compartment firewall to the fuel pump location are the vulnerable area. subject to radiant heat from the fan housing casting. thats the risky part. also the little lengths of plastic line in the engine bay. these get cooked a bit too. not as bad as section under the car though.
i pulled mine out two years ago. all the stuff in the tunnel was fine. still almost factory new. the stuff exposed was not something i wanted to risk running fuel through anymore.
@http://www.914world.com/bbs2/index.php?showuser=2939
great looking car.
about the only thing i can think of might be to take a look at CV joints and see if they need repacking. i did mine. similar story to your car. brake fluid change as per superhawk suggestion. rest of it - don't fix something that ain't broke. but maybe pay attention to all fuel lines.
enjoy the car. its beautiful.
Trans lube?
And given the recent thread about wiper linkage corrosion, maybe trying to get some grease into the shafts?
Great looking example, thanks for posting pics.
Enjoy her in good health
I am really embracing my mechanics advice to me. Pretty much "how I learned to stop worrying and love the 914".
Sure, there are things that should be fixed, but as long as it starts and is fun every day, and my fun isn't making the car fall apart, whatever. Somebody else can obsess over my new custom fuel pump holder.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)