Printable Version of Topic

Click here to view this topic in its original format

914World.com _ 914World Garage _ Adjusting Idle PMO Carbs - Six Cylinder

Posted by: mmascari Jun 16 2023, 02:23 PM

Do I turn the idle adjuster clockwise or counter-clockwise to Increase the idle?

Posted by: porschetub Jun 16 2023, 04:13 PM

QUOTE(mmascari @ Jun 17 2023, 09:23 AM) *

Do I turn the idle adjuster clockwise or counter-clockwise to Increase the idle?

Clockwise ,my tip in throttle isn't a lot,just enough to get idle up to factory setting,cheers.

Posted by: brant Jun 16 2023, 04:14 PM

Wrong thread
Delete

Posted by: Steve Jun 16 2023, 05:45 PM

QUOTE(mmascari @ Jun 16 2023, 01:23 PM) *

Do I turn the idle adjuster clockwise or counter-clockwise to Increase the idle?

Clockwise, but remove the cross bar from one side when making the adjustment.
I also used the ball thingy on the throats to make sure they were the same on both sides. Then put the cross bar back on and adjust accordingly if it throws the carbs off.
https://www.amazon.com/Latest-Rage-5385730856-Carburetor-Airflow/dp/B00CMC57R0/ref=asc_df_B00CMC57R0/?tag=hyprod-20&linkCode=df0&hvadid=309898128610&hvpos=&hvnetw=g&hvrand=17901556736193398373&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9031558&hvtargid=pla-568420224882&psc=1

Posted by: nditiz1 Jun 16 2023, 07:00 PM

As Steve said.

Don't buy that one from Moore Parts/latest Rage it is garbage. Spring 20 more for the German brand one.

Posted by: porschetub Jun 20 2023, 04:44 PM

QUOTE(Steve @ Jun 17 2023, 12:45 PM) *

QUOTE(mmascari @ Jun 16 2023, 01:23 PM) *

Do I turn the idle adjuster clockwise or counter-clockwise to Increase the idle?

Clockwise, but remove the cross bar from one side when making the adjustment.
I also used the ball thingy on the throats to make sure they were the same on both sides. Then put the cross bar back on and adjust accordingly if it throws the carbs off.
https://www.amazon.com/Latest-Rage-5385730856-Carburetor-Airflow/dp/B00CMC57R0/ref=asc_df_B00CMC57R0/?tag=hyprod-20&linkCode=df0&hvadid=309898128610&hvpos=&hvnetw=g&hvrand=17901556736193398373&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9031558&hvtargid=pla-568420224882&psc=1

My experience was I found I hadn't exactly set up the drop links after replacing the worn ball cups ,found when hooking up the crossbar again it was clearly obvious they weren't even.
Reset them and much improved,rebuilt the all the crossbar throttle linkages as due wear on those ball cups I had lots of slack in the system @ those points.
IMO if all this is sorted and your carbs are fresh and you have even vacuum on all throats set up is pretty straight forward.
Cheers.

Posted by: Luke M Jun 20 2023, 07:18 PM

This is PMO EFI but linkage is the same.

https://www.youtube.com/watch?v=LGjN3wrGi0g

Posted by: porschetub Jun 20 2023, 11:36 PM

QUOTE(Luke M @ Jun 21 2023, 02:18 PM) *

This is PMO EFI but linkage is the same.

https://www.youtube.com/watch?v=LGjN3wrGi0g

Ok but the title was "PMO carbs" from the OP ???.

Posted by: VaccaRabite Jun 21 2023, 08:34 AM

QUOTE(porschetub @ Jun 21 2023, 01:36 AM) *

QUOTE(Luke M @ Jun 21 2023, 02:18 PM) *

This is PMO EFI but linkage is the same.

https://www.youtube.com/watch?v=LGjN3wrGi0g

Ok but the title was "PMO carbs" from the OP ???.

linkage adjustment is the same, either way.

Zach

Posted by: porschetub Jun 21 2023, 02:45 PM

QUOTE(VaccaRabite @ Jun 22 2023, 03:34 AM) *

QUOTE(porschetub @ Jun 21 2023, 01:36 AM) *

QUOTE(Luke M @ Jun 21 2023, 02:18 PM) *

This is PMO EFI but linkage is the same.

https://www.youtube.com/watch?v=LGjN3wrGi0g

Ok but the title was "PMO carbs" from the OP ???.

linkage adjustment is the same, either way.

Zach

Exactly.

Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)