Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ 914/6 conversion on BAT
Posted by: Tom_in_NH Mar 21 2024, 01:07 PM
I noticed a different engine mount arrangement on this conversion. It uses a steel square tube mounted using 911 motor mounts in the standard 914/4 receivers. No idea what the engine console mount looks like though.
It looks like a less involved conversion mount if there isn't much fabrication at the engine console.
Here's a link to the auction/photos:
https://bringatrailer.com/listing/1973-porsche-914-124/
Posted by: brant Mar 21 2024, 01:14 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
Posted by: mepstein Mar 21 2024, 02:56 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
Also didn't handle heat exchangers - iirc.
Posted by: eric9144 Mar 21 2024, 03:34 PM
I had that on my 1st conversion way back in the 90's, was an easy button but not ideal by any means and it creates a low point under the car--I remember scraping it on a high speed bump at one point. Go with a bulkhead type mount if at all possible, much better 
Posted by: Thunderchief Mar 21 2024, 04:30 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
I have that type on one of my -6's. Where does it crack/fail?
Posted by: Steve Mar 21 2024, 05:40 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
I have that type on one of my -6's. Where does it crack/fail?
It depends on the manufacturer. MSDS used to sell them. I never had a problem with there bar. I used it over 20 years and only changed to the Rich Johnson center mount so I could run heat exchangers. PMS used to sell a curved one that scraped the ground and had other problems.
IMHO Pretty kludgy to put a heavy oil tank in the rear trunk. Just to save a couple hundred bucks on a retro tank?
Posted by: mepstein Mar 21 2024, 06:59 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
I have that type on one of my -6's. Where does it crack/fail?
It depends on the manufacturer. MSDS used to sell them. I never had a problem with there bar. I used it over 20 years and only changed to the Rich Johnson center mount so I could run heat exchangers. PMS used to sell a curved one that scraped the ground and had other problems.
IMHO Pretty kludgy to put a heavy oil tank in the rear trunk. Just to save a couple hundred bucks on a retro tank?
“The Targa top is no longer stowable in the rear trunk due to the installation of an aluminum oil tank and spin-on oil filter adapter.”
Posted by: Maltese Falcon Mar 21 2024, 08:15 PM
believe this is the quick six type of conversion part that was available in the 80's before bulkhead conversion mounts became the standard.
many of the quick six type cracked and had failure problems
don't believe any of the bulkhead style have this problem these days
I have that type on one of my -6's. Where does it crack/fail?
It depends on the manufacturer. MSDS used to sell them. I never had a problem with there bar. I used it over 20 years and only changed to the Rich Johnson center mount so I could run heat exchangers. PMS used to sell a curved one that scraped the ground and had other problems.
IMHO Pretty kludgy to put a heavy oil tank in the rear trunk. Just to save a couple hundred bucks on a retro tank?
What's happening my friend @http://www.914world.com/bbs2/index.php?showuser=822 ! ¿ The short story on my Qwik-6 conversion mount started in 1977 when I converted my '74 2L. I started out with the "Goodspeed" (bar) style mount, which failed in about 6 months and the 2.7 turbo six was saved by hanging on its AN#12 and #16 oil lines
So I reinvented it with thicker, cold roll steel tube bar, .375" welded cradle, and gussets...still with the car today. The 5L Cayenne v8 in the 8gtt runs a bar style but it's 1.25" square /solid steel and 2) .375" welded cradles. Engine weighs just a bit more than a 930 engine, and
the bar does not hang much lower than the floorpan; no deflection either.
Posted by: Karl R Mar 21 2024, 09:14 PM
I'm kinda in the market for one of these types of mounts. I don't weld and don't want to get hung up trailering to a welding shop and such. I'd like to use the easy solution while I sort out oil lines, fuel system, etc then drive it to a welder.
Posted by: Tdskip Mar 21 2024, 09:40 PM
I'm kinda in the market for one of these types of mounts. I don't weld and don't want to get hung up trailering to a welding shop and such. I'd like to use the easy solution while I sort out oil lines, fuel system, etc then drive it to a welder.
Do a search for a mobile welder that can come to you - as other has said it is worth doing the firewall mount.
Posted by: live free & drive Mar 22 2024, 01:51 PM
There is a quick six bar for sale recently in the for sale area:
http://www.914world.com/bbs2/index.php?showtopic=369622
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)