I started out to restore my 73 2.0L to its original D-Jetronic fuel injection. At some point I decided that I while I was working on the fuel system I might as well replace the plastic lines with stainless steel and relocate the pump. Here are some pictures with commentary of the fuel line upgrade.
Overall the fuel line install was fairly easy. It would have been much easier if I hadn't decided to run one solid line from the tank all the way to by the MPS sensor. If I did this over again I would do everything the same except that the solid lines would stop at the right side of the firewall and I'd run hose from there.
First, I removed the interior and pulled the fuel tank. Here is a photo of the tank halfway out. The hoses on the tank were long enough that I didn't need to disconnect them through the service hole below the tank. I was able to lift the tank to this position and then disconnect the hoses from above. The new hoses I installed are also long enough to permit access from above.
Attached thumbnail(s)
Here is a view of the old lines beneath the tank. The old lines come out of a rubber block that connects with the front part of the tunnel. They stick out a few inches.
There is some surface rust under the tank. I cleaned this up with sandpaper and primed it with Zinc-Chromate before installing the new lines.
Attached image(s)
After the tank was out I pushed the lines back through the block and then went back to the engine compartment, disconnected everything, and pulled. The lines came out easily. I haven't got a clue how you would put plastic lines back in. It would be like pushing a wet noodle up the tunnel.
Here are the lines out of the car. They are steel for the first foot or so and then plastic. The plastic was in pretty good shape but I am still happy I replaced them.
There is a ~30 degree bend about xix inches from the end. The new lines go in much easier if you make this bend *before* you stick them down the tunnel.
Attached image(s)
Another view of the old lines showing the bend near the end.
Attached image(s)
After the old lines are out its time to put the new lines in. I used 5/16 stainless steel tubing - available from Summit Racing. It comes in a 20 foot length all coiled up. What a pain. I would much rather have started with a straight piece. Also 5/16 inch steel brake line would work fine here. The stainless is nice, but the chance of corrosion in the tunnel is minimal.
I put the 30 degree bend in the line before inserting it in the tunnel. Then I test fit the line to mark where the 90-degree bend (actually about a 110 degree bend followed by a 20 degree bend the other way) at the firewall should be. Then I put the line back through the tunnel. Inserting the lines in the tunnel is fairly easy. You just need to make sure you miss the harness that is right on the other side of the firewall.
I reused the original grommets which were in good condition. The small one was a tight fit. The large one needed some RTV to make it snug on the 5/16 line.
Here's a picture with one line in and the other on the way.
Attached thumbnail(s)
The lines are run along the firewall and held in place with Adel clamps. I'm probably paranoid, but I don't want them vibrating around and work hardening.
The lines make a 90 degree bend above the heater hose. If I were to do it again I'd stop the hard lines there. Most of the time was spent making the bends after this point and working the lines up through the tin. There is little to be gained by running hard line for the last two feet and that run would be much easier with hose.
Attached thumbnail(s)
Here are the lines running along the right side of the engine compartment. The come up through the original grommets, right under the MPS.
Meanwhile back under the gas tank, I fabricated a steel bracket to hold the lines. This is probably not needed. In retrospect the rubber block should do an adequate job of keeping the lines from vibrating.
If you do make a bracket, be careful drilling holes here. There is a brake line on the other side of this panel.
Attached thumbnail(s)
Good thread, thanks! I'll be doing this soon.
You need to replace those clamps with real FI hardware.
How are you clamping the lines in the tunnel?
The lines are not clamped in the tunnel. They are held at the rear of the tunnel by grommets and at the front by the rubber block. They should be OK without clamps unless some kind of resonance causes them to vibrate in the tunnel.
QUOTE |
You need to replace those clamps with real FI hardware |
From what I've seen, it's the edges of the clamp. Regular hose clamps have sharp edges where FI clamps are curled up. I have seen old FI hose that was cracked and cut at the clamp.
Great job
This is one my list before I put the engine back in and your thread is going to help alot.
Thanks!
Great job, thanks for the post. I have a couple of questions.
1) Just to be sure : Did you do the whole job w/ the engine in the car ?
2) When you are pushing the lines in from the rear, how do you manage to get them to come out at the front end of the tunnel ? I haven't done any work in that area, but it sounds like a tough job : like threading a needle from a foot away.
3) What do you use to cut the tubing ? Would a regular (home plumbing style) tubing cutter do the job ? I'm guessing this stuff is too hard for that.
4) Did you use a special beding tool, or just do it by hand ?
Thx,
Jeff
QUOTE (jsteele22 @ Sep 16 2005, 09:06 AM) |
1) Just to be sure : Did you do the whole job w/ the engine in the car ? 2) When you are pushing the lines in from the rear, how do you manage to get them to come out at the front end of the tunnel ? I haven't done any work in that area, but it sounds like a tough job : like threading a needle from a foot away. 3) What do you use to cut the tubing ? Would a regular (home plumbing style) tubing cutter do the job ? I'm guessing this stuff is too hard for that. 4) Did you use a special beding tool, or just do it by hand ? Thx, Jeff |
QUOTE (Headrage @ Sep 16 2005, 08:28 AM) |
From what I've seen, it's the edges of the clamp. Regular hose clamps have sharp edges where FI clamps are curled up. I have seen old FI hose that was cracked and cut at the clamp. |
I got all of mine at either Autozone or Pep-Boys...
From your last picture it looks like you used 2 different types of hose under the gas tank. What was the reason? Also, from an old post the ends of the metal fuel line was threaded so the hose gets a good bite. Do you think there is any chance of your connections coming apart? This is my next project. I am glad it can be done with the engine in place. How long did it take including removing and replacing the interior? Thanks, Eddy
QUOTE (smooth_eddy @ Sep 16 2005, 02:57 PM) |
From your last picture it looks like you used 2 different types of hose under the gas tank. What was the reason? Also, from an old post the ends of the metal fuel line was threaded so the hose gets a good bite. Do you think there is any chance of your connections coming apart? This is my next project. I am glad it can be done with the engine in place. How long did it take including removing and replacing the interior? Thanks, Eddy |
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)