anybody got a trick to doing this?
I dont want to take the HEs off if I don't have to....
is there a trick to popping the valve cover with a screwdriver with the HEs on?
I tried popping the sides, but that didnt work out?
b
remove the H/E????
are you on crack???
you should be able to use a screwdriver, a wrench etc.....to provide leverage to pull the wire down....try the middle of the cover....
listen....
look at what i said...
a wrench might work...not much space though....
No trick, just the normal proceedure.
Reach down from above with a thick flat-bladed screwdriver THROUGH the bailwire... Pry DOWNWARD and the bail wire should slide down to the bottom of the valve cover. Then stick your screwdriver tip into the little hole on the corner of the valve cover and pull away from the head. Tada! It's off.
PS: Listen to what Mueller said... no need to take the HEs off.
QUOTE (Brando @ Oct 18 2005, 01:33 PM) |
No trick, just the normal proceedure. Reach down from above with a thick flat-bladed screwdriver THROUGH the bailwire... Pry DOWNWARD and the bail wire should slide down to the bottom of the valve cover. Then stick your screwdriver tip into the little hole on the corner of the valve cover and pull away from the head. Tada! It's off. PS: Listen to what Mueller said... no need to take the HEs off. |
QUOTE (bd1308 @ Oct 18 2005, 12:33 PM) |
listen.... look at what i said... a wrench might work...not much space though.... |
You can always take a shop rag, loop it around the bail, grab both ends, & pull down.
QUOTE (markb @ Oct 18 2005, 12:42 PM) |
You can always take a shop rag, loop it around the bail, grab both ends, & pull down. |
QUOTE (markb @ Oct 18 2005, 12:42 PM) |
You can always take a shop rag, loop it around the bail, grab both ends, & pull down. |
QUOTE (markb @ Oct 18 2005, 12:42 PM) |
You can always take a shop rag, loop it around the bail, grab both ends, & pull down. |
what year is your car? the 75-76 HEs can be a PITA, but there is still room to work around them. just gotta get creative.
QUOTE (Mueller @ Oct 18 2005, 01:41 PM) | ||
I know there is not much space....you need to figure out how to get the wire to lift up and over the protrutions of the valve cover in order to get the wire to swing down..... a wrench "will" work if you pick the right size and angle....how sad to be out-smarted by a valve cover |
If the bails are installed upside down, and you can't believe how many I see that way, the cover won't come off without removing the bail. I insert a medium sized screwdriver from the bottom, and pry the bail out and down. Installation is the reverse. As you view the bail, it should dish upward from the pivot point. The Cap'n
VW symbol upside-down, correct cap'n?
b
QUOTE (bd1308 @ Oct 18 2005, 12:57 PM) |
it's too damn hot outside, i'm on gravel, and i have oil dripping on my face and mouth. plus my friend was bitching about the heat.... b |
QUOTE (bd1308 @ Oct 18 2005, 12:00 PM) |
VW symbol upside-down, correct cap'n? b |
QUOTE (bd1308 @ Oct 18 2005, 12:57 PM) |
it's too damn hot outside, i'm on gravel, and i have oil dripping on my face and mouth. plus my friend was bitching about the heat.... b |
QUOTE (Cabasa @ Oct 18 2005, 12:27 PM) |
QUOTE (bd1308 @ Oct 18 2005, 12:36 PM) |
maybe my screwdriver is too big.... |
ya'll crack me up....
Cap'n the VW emblem goes upside down...looks like M something
M
^ <-----that's what it looks like
anyway, all valves are adjusted....lost one pair of jeans and a mercedes shirt.....
Now i still have some tap tap noise, which i think is due to me being conservative with the valve adjust.....now on to carb fine tuning.
OH and apparently the head sucked in the gasket...it was wierd....and on the other side it moved pretty far over.....so there's my oil burning problem....
AA, my driver was simply, too big......
thanks guys!
b
i pull HE's to change my alternator belt.
QUOTE (Aaron Cox @ Oct 18 2005, 05:02 PM) |
i pull HE's to change my alternator belt. |
QUOTE (Aaron Cox @ Oct 18 2005, 04:02 PM) |
i pull HE's to change my alternator belt. |
flame away...i'm off to get cleaned off.
QUOTE (Headrage @ Oct 18 2005, 04:10 PM) | ||
Really? I've only needed to do it when I am trying to fix my leaky tail light housings. |
QUOTE (Aaron Cox @ Oct 18 2005, 04:16 PM) | ||||
i had to cut a hole in my firewall to get the headlights to work too! |
QUOTE (Aaron Cox @ Oct 18 2005, 04:16 PM) |
i had to cut a hole in my firewall to get the headlights to work too! |
QUOTE (Grimstead @ Oct 18 2005, 04:57 PM) | ||
How dumb are you???? Everyone knows you just need to put the fuild in that channel between the seats! Duh! |
You guys are funny. You should not ride him so much. hes a young guy learning to work on his car.
Back in my high school days my friend said he was going to change the oil in his Chevy. Stopped by a little later to check on his progress. Found that he had removed the oil pan still full of oil! I asked didnt you see the drain plug? He said what is a drain plug?
When you stop learning its time to die
David
Bumper bolts are easy..
Using:
Telekinesis.. Ask Aaron how... he's writing a book about it with a forward from Slits.
MattR
Miles,
have you tried a Dremel?
I DON'T speak from experience on this, just speculation....those little Dremels will cut through everything....
why the hell ASK me to sell my car...?
I'm keeping it AND the parts car and there's nada anyone can do....
everybody needs to chill out...stop ribbing me.
If you all don't want me here, i'll go to pelican....this is rediculous (sp)
oh and before I get a mouthfull from you-know-who....
YES I KNOW THE ABOVE WORD IS SPELLED WRONG. i'm not a english major.
it could be worse, I could not give a damn and not work at anything and have you all pay for my living.....
b
QUOTE (bd1308 @ Oct 18 2005, 06:32 PM) |
i'll go to pelican... |
QUOTE (Headrage @ Oct 18 2005, 07:55 PM) | ||
Really? |
damn, did he really leave
QUOTE (bd1308 @ Oct 18 2005, 11:57 AM) | ||||
it's too damn hot outside, i'm on gravel, and i have oil dripping on my face and mouth. plus my friend was bitching about the heat.... b |
QUOTE (bd1308 @ Oct 18 2005, 06:57 PM) | ||||
fine. see ya all I guess i'll see some of you all at FFC if I end up actually making it. |
QUOTE (Grimstead @ Oct 18 2005, 08:28 PM) | ||||||
Don't go! Just tell us to F off and get over it. I know for a fact that the majority of the guys in the post are just goofing off and it has nothing to do with you personally. I myself hear it from Aaron all the time. So in the memorable words of Gandhi "Don't hate the playa, hate the Game" |
Lets all take a lesson from Earl.......karma. I made my own list, #126 made fun of Britt.
QUOTE (Aaron Cox @ Oct 18 2005, 08:51 PM) |
hey, at least people in canada dont think your gay...... |
QUOTE (Grimstead @ Oct 18 2005, 09:38 PM) | ||
I owe you for that one |
QUOTE (Aaron Cox @ Oct 18 2005, 08:39 PM) | ||||
a sierra nevada is proper pennance |
QUOTE (Alison Baker @ Oct 18 2005, 09:51 PM) | ||||||
I would recommend something stronger then that Aaaaaaaaaaaaaaaaron......would n't you say so ???? |
Martin and I WILL BUY YOU SOME Of these aaaaaaaaaaaaaaaaaaaaron ..................Yeah Baby
Wow Britt, way to take a joke.
Suck it up, crack a few back, and live life.
QUOTE (Aaron Cox @ Oct 18 2005, 08:51 PM) |
Britt. chill out. look at all the ribbing i get.... |
QUOTE (bondo @ Oct 18 2005, 11:31 PM) | ||
Aaron: Ribbed for your pleasure! (I don't normally take part in the Aaron bashing, but I couldn't pass that up) |
QUOTE (bondo @ Oct 18 2005, 10:31 PM) | ||
Aaron: Ribbed for your pleasure! |
QUOTE (Alison Baker @ Oct 18 2005, 09:51 PM) | ||||||
I would recommend something stronger then that Aaaaaaaaaaaaaaaaron......would n't you say so ???? |
Oh man that's wrong. anytime I find your beer in the store I buy ALL of it.
QUOTE (Grimstead @ Oct 19 2005, 07:09 AM) | ||||||||
That's it! A man has to put his foot down somwhere and for me it is when (I walk) people start bashing my Beer! |
We'll see about that....
You have been challenged!
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)