Printable Version of Topic
Click here to view this topic in its original format
914World.com _ 914World Garage _ Anyone know who makes this harness bar?
Posted by: neo914-6 Nov 22 2005, 02:03 AM
Also need to know where to purchase.
Attached image(s)
Posted by: Joe Sharp Nov 22 2005, 02:10 AM
There are no markings on the bar.
:PERMAGRIN: Joe
Posted by: sj914 Nov 22 2005, 06:19 AM
maybe a custom bar. 
Posted by: J P Stein Nov 22 2005, 09:21 AM
That bar positions the belts way too high.
Posted by: Aaron Cox Nov 22 2005, 10:37 AM
The previous owner of joes car said it was made in somewhere in huntington beach.... i think is what he said.
ironically, joe lives there too.
i wanted to make one with 2 humps..one over each headrest.
Posted by: Headrage Nov 22 2005, 10:42 AM
| QUOTE (Aaron Cox @ Nov 22 2005, 08:37 AM) |
| i wanted to make one with 2 humps..one over each headrest. |
Be a bitch to clean the back window.
Posted by: Aaron Cox Nov 22 2005, 10:44 AM
| QUOTE (Headrage @ Nov 22 2005, 09:42 AM) | ||
Be a bitch to clean the back window. |
you can still move the seats forward for acces allan
Posted by: Headrage Nov 22 2005, 11:02 AM
| QUOTE (Aaron Cox @ Nov 22 2005, 08:44 AM) | ||||
you can still move the seats forward for acces allan |
Still gotta get behind that bar...
Posted by: Aaron Cox Nov 22 2005, 11:04 AM
| QUOTE (Headrage @ Nov 22 2005, 10:02 AM) | ||||||
Still gotta get behind that bar... |
bar is not resting on the window either... plenty of room for a rag.
Posted by: greg.treadway Nov 22 2005, 11:06 AM
Cool bar. I also think it had to be a custom job though. I have not seen one before.
Posted by: J P Stein Nov 22 2005, 11:17 AM
Yes, cool......if that's what is important 
Posted by: Headrage Nov 22 2005, 11:21 AM
| QUOTE (Aaron Cox @ Nov 22 2005, 09:04 AM) | ||||||||
bar is not resting on the window either... plenty of room for a rag. |
Still gotta go outside to do it...
Posted by: Aaron Cox Nov 22 2005, 11:26 AM
| QUOTE (Headrage @ Nov 22 2005, 10:21 AM) | ||||||||||
Still gotta go outside to do it... |
go outside?
Posted by: Headrage Nov 22 2005, 11:36 AM
| QUOTE (Aaron Cox @ Nov 22 2005, 09:26 AM) | ||||||||||||
go outside? |
Keep yer car in the house?
Posted by: Aaron Cox Nov 22 2005, 11:40 AM
| QUOTE (Headrage @ Nov 22 2005, 10:36 AM) | ||||||||||||||
Keep yer car in the house? |
how is that point relavent? i dont wash cars inside.....getting dizzy
Posted by: Headrage Nov 22 2005, 11:45 AM
| QUOTE (Aaron Cox @ Nov 22 2005, 09:40 AM) | ||||||||||||||||
.....getting dizzy |
I'm done...
Posted by: Aaron Cox Nov 22 2005, 01:45 PM
| QUOTE (Headrage @ Nov 22 2005, 10:45 AM) | ||||||||||||||||||
I'm done... |
you sure?
so ideally, the harness bar, should be barely above the backpad? say like 1" or so?
Posted by: lagunero Nov 22 2005, 03:08 PM
| QUOTE (Aaron Cox @ Nov 22 2005, 11:45 AM) | ||||||||||||||||||||
you sure? so ideally, the harness bar, should be barely above the backpad? say like 1" or so? |
look! a maze!
Posted by: 1973914 Nov 22 2005, 04:04 PM
Three things horribly wrong with that setup
1. The belts are attached directly to it. This is not correct unless it is part of a full cage. If the bar is connect between the two upper seatbelt holes, it is not sufficient. Unless part of a full cage, you cannot hook the belt to it. That is why they call them harness GUIDE bars...
2. If this is for a street car, then you are asking for a serious head injury with the bar positioned there. Front or rear collision (or rollover) will subject occupants to significantly higher risk of injury with those bars there. Belts stretch and occupants move at significant G loads.
3. Location of restraint is incorrect. Belts should approach the shoulder from behind at no more than a 10 degree angle. Raised up high like that, the occupant would be allowed to travel up the belts in the case of a rollover and placed in contact with the bar or with the roof it it stays attached or the road/tree/gravel/whatever if the roof comes off.
At least you will be able to get at the window to clean your brains off!
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)