I recently converted to 6cyl, and now when I start it it blows the oil filter seal.
We traced the oil and it is flowing freely through the system and cooler back into drysump.... we noticed that hoses were a little softer on the out side of the oil cooler (RX7 turbo cooler) so we bypassed it and it solved the problem.
I have since bought a new cooler 914-6, and now it blows again.
Any thoughts as to why this might be happening?
I checked both oil pressure springs and valves and they are there, loose and movable so they are not stuck.
Doug
right not the exxon valdez capt'n
Moving to the garage...
By any chance are you bulging the filters? What filter are you using?
I had the same problem on my 4 cylinder race motor... plus I was bulging the filter. I went to a Fram HP 1 full flow filter and RTV the seal and problem solved. Make sure you use the HP which is the High Performance filter and NOT the standard PH filter. Also try to keep the revs low on start up until the oil warms up.
GB
I agree with Mark, RTV belongs nowhere near an engine.
K&N filters are very strong, but you need to pull the bypasses out and make sure your don't have some trash behind them. You should also check and make sure you don't have two gaskets stuck together.
I am using HP 1 from patrick motorsports.
I pulled pressure springs to make sure they were not stuck.
I guess what I could do is pull them and crank it to blow by anything that would be stuck.
But here is the kicker. If I bypass the oil cooler it works fine. (putting a Male to Male connector, so lines are still used).
We are thinking that the oil presure blow off springs are super strong and not stock and we are ordering stock springs to see if that solves it.
Thanks for the input
Is the cooler blocked? if removing the cooler from the line solves you pressure problem then I suspect the cooler. Or a cooler T-stat?
Frams are for olf Fords you don't care about. RTV is for engines you don't care about. Use ONLY the OE filters, use only the correct weight oil, and check the plumbing to the external cooler, including the cooler itself. I don't remember ever seeing a 911 motor with excessive oil pressure. The Cap'n
some rx7 coolers have thermostats in em.....
bulging - does the filter "bulge" or grow in shape???
Bulges like a balloon till the seal pops out or it splits.
I've had one burst on the test stand hosing 3 cars, my 12 foot ceiling and a wall that was 40 feet away.
No Bulging accept the oil filter seal seal that you see expanding out then blowing.
As for Oil Cooler, I have blown compressed air through it it is clean.
I have removed thermostat. (RX7)
I now have 914-6 cooler.
My friend says I need in on one side and out on the other cooler.
I do not see hos that would be any different then in/out on same side.
B & B coolers are in/out on same side and I used them with good luck.
HELP
oil pressure springs on the motor have nothing to do with the oil return(scavenge) side of the pump on a six.
I have a hp-1 on mine never any problem. -12 6 foot long . how is your set up plumbed?
oil filter hooked up in/out backwards ?
Have you put a gauge on the engine to see how much oil pressure you're running?
And is the engine stock? Stock oil pump, relief pistons/springs, etc.
The thermostat on the scavenge side is there to keep cold oil away from an oil cooler.
The scavenge side is unregulated for pressure.
If your filter is upstream of the cooler,.......I'm confused.
My set up bypasses the oil cooler till the oil is hot. When cold, it goes thru the filter to the tank....the Mahle filter has a high pressure relief valve to bypass the filter element
should it overpressure....
A sketch or pic of your plumbing would be good
I am totally confused by your descriptions.
Here is a pic of my thermostat and an explanation of what is going on here.
The line on the right is output from the scavenge pump....the fitting on the engine sump, pass side. The 2 lines diving into the heat duct are in/out from the oil cooler.
The lefthand line goes to the oil tank ...to which the oil filter is attached. The internal plumbing of the stock tank routes this oil thru the filter and then to the tank.
When cold, the oil goes in from the right and out to the left. When hot, the oil comes in from the right(still ) then out the bottom fitting on the thremo to the oil cooler and returns to the top thremo fitting and then to the tank via the top fitting & lefthand line.
The thermo regulates temp via partial opening/closing thus at times oil is flowing thru all 4 lines at once. This particular thermo has a pressure relief valve that will bypass the oil cooler should there be an obstruction. It will not allow full flow of cold oil to the cooler.
Oil filters made for dry sump Porsches have a pressure relief valve which will open to shunt oil by the filter element and straight into the tank. The cold oil pressure on the scavenge side can be very high....165psi at cold start-up was observed by a fella I talked (internet) to.
Oh yeah, the pic
Attached image(s)
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)