Printable Version of Topic
914World.com _ 914World Garage _ Removing rear sway bar
Posted by: itsa914 Nov 9 2003, 09:54 PM
OK dumb question. I got the rear sway bar unbolted
finally from the chassis, was is the correct way to get
the drop link off from the bottom of the shock?? Does
it just pop off??
- Garold
Posted by: seanery Nov 9 2003, 09:55 PM
yes.
Don't forget to save the ball end from the shock mounts.
Posted by: itsa914 Nov 9 2003, 09:57 PM
QUOTE
Don't forget to save the ball end from the shock mounts.
OK, how do you remove those??
Posted by: Jeroen Nov 9 2003, 09:57 PM
use a "pickle fork"
cheers,
Jeroen
Posted by: seanery Nov 9 2003, 10:00 PM
the ball ends are part of the lower shock bolts, just unbolt em and pull 'em out.
Posted by: itsa914 Nov 9 2003, 10:00 PM
Is that a dill pickle fork
Posted by: seanery Nov 9 2003, 10:01 PM
Here is a pic of everything that you need to take with the rear.
Posted by: itsa914 Nov 9 2003, 10:05 PM
anything else I need to do before I remove that bolt?? This
is comming off a parts car.
Posted by: seanery Nov 9 2003, 10:07 PM
watchout for the wheels drooping when you do. If you don't need them on the car take 'em off.
now would be a good time to remove the whole rear suspension.
Posted by: itsa914 Nov 9 2003, 10:13 PM
QUOTE
now would be a good time to remove the whole rear suspension
All I want is the sway bar & hardware
everything else is
scrap. I relly don't want to mess with the suspension.
Posted by: SirAndy Nov 9 2003, 10:20 PM
QUOTE(itsa914 @ Nov 9 2003, 08:13 PM)
All I want is the sway bar & hardware
everything else is
scrap. I relly don't want to mess with the suspension.
take it out anyways. there could be some hidden treasure in there
like, a whole stack of alignement shims, or adjusteable shocks, or unbent trailing arms.
sell (or give it to me for free
) every little piece of it that's not rusted ...
Andy
Posted by: rdauenhauer Nov 9 2003, 11:00 PM
Garold, assuming this is an otherwise stock LE (rust & re-paint notwithstanding) It would be interesting to note: Rear shocks- Make, Front strut housing & inserts- make?
Posted by: itsa914 Nov 10 2003, 04:19 PM
QUOTE
take it out anyways. there could be some hidden treasure in there like, a whole stack of alignement shims, or adjusteable shocks, or unbent trailing arms
OK how do you tell for sure that the trailing arms are not bent?
They look ok, I haven't taken them off yet, just wondering.
Also Do I need to compress the spring on the shock before
I remove it or can it be removed as one complete piece?
- Garold
Posted by: SirAndy Nov 10 2003, 05:23 PM
QUOTE(itsa914 @ Nov 10 2003, 02:19 PM)
OK how do you tell for sure that the trailing arms are not bent?
They look ok, I haven't taken them off yet, just wondering.
Also Do I need to compress the spring on the shock before
I remove it or can it be removed as one complete piece?
as for the trailing arms, ask brad
if you're asking if you need to compress the spring to remove the shock from the chassis, NO.
if you're asking if you need to compress the spring to remove the spring from the shock, MAYBE.
if the springs anywhere near stock, you'll be able to compress them by hand if needed.
usually, when you unbolt them, you'll notice than there's no pressure on the nut for the last few threads anyways.
as always, point them away from you, just in case ...
later,
Andy
Posted by: itsa914 Nov 10 2003, 09:06 PM
QUOTE
if you're asking if you need to compress the spring to remove the shock from the chassis, NO.
yep that is what I was asking.
Thanks Andy
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)