Okay, so my '73 1.7 has been misfiring and without power. I checked the dwell, it seems fine. Plenty of spark on all plug wires. New plugs. Tried pulling the injector wires at idle, and on cylinders one and two, the car will die quickly when either wire is pulled. On cylinders three and four, however, this is not the case at all. The car will continue to run just the same (to my ear and according to the tach) indefinitely. I figured it must be either an injector issue or a wiring issue. I swapped the cylinder 1 and cylinder 3 injectors, and the problem stayed with the cylinder, not the injector. Shit.
So I replaced the wiring harness with a spare Todd sent me home with. Still having the same issue. Fuch!
Any other ideas? A local shop told me I had a vacuum leak. Hmmm. Tried replacing the hoses, but didn't help at all.
I've got an XR700 sitting here, thought I might install that. Figured if it did turn out to be the points, that would solve it. Basically just reaching.
Help?
Thanks!
Cole
check the injector point on the distributor
The injector trigger points. (lower part of the Dizzy)
The injector Grounds (Under plenum, passenger side.)
Make sure the wiring to the injectors is correct...i.e. the injector wires could be flipped, so the injectors are all firing at the wrong time.
Also, check that the ignition wiring, the firing order, is correct, the car will run (like crap) if the plug wires are put on backwards..
Rich
Are you related to britt?
You have changed to many things.
Go back.
the FI trigger points.
Take out the dizzy.
In the lower half of the dizzy is a part that has two screws holding it in, and has a plu connector for the FI harness.
Take out the two screws, and carefully pull out this part, your FI trigger points.
Take an ohm meter and test to see that each side makes contact when they are closed, you might need to adjust the angle, or possibly clean the points to get them to make contact.
Use the meter on OHMs with this part disconnected from everything.
Once you get those working again.
Put them back in the dizzy
Put the dizzy back in
Did you remember the previous position of the dizzy prior to removing it?
If not, you need to static time it to get it close to correct, then use a timing light to get it perfect.
If the timing is wrong, it wont start
If the dwell it wrong it wont start
If you forgot to plug one of the FI plugs back in, it wont start
Rich
Before you get carried away make sure to check the Kuhneuter valve and clean the flux capacitor
--><div class='quotetop'>QUOTE(scotty b @ Jan 3 2007, 07:49 PM) </div><div class='quotemain'><!--quotec-->
Before you get carried away make sure to check the Kuhneuter valve and clean the flux capacitor
[/quote]
Thought those only came on the L-Jet systems????
Cole
[quote name='wrpspddrvr' date='Jan 3 2007, 04:50 PM' post='842 085']
--><div class='quotetop'>QUOTE(scotty b @ Jan 3 2007, 07:49 PM) </div><div class='quotemain'><!--quotec-->
Before you get carried away make sure to check the Kuhneuter valve and clean the flux capacitor
[/quote]
Thought those only came on the L-Jet systems????
Cole
[/quote]
Damn you're right I wasn't paying attention to your setup. Your car needs a new rhomulan bypass chord. That's what you have going on
[quote name='scotty b' date='Jan 3 2007, 07:54 PM' post='842089']
[quote name='wrpspddrvr' date='Jan 3 2007, 04:50 PM' post='842 085']
--><div class='quotetop'>QUOTE(scotty b @ Jan 3 2007, 07:49 PM) </div><div class='quotemain'><!--quotec-->
Before you get carried away make sure to check the Kuhneuter valve and clean the flux capacitor
[/quote]
Thought those only came on the L-Jet systems????
Cole
[/quote]
Damn you're right I wasn't paying attention to your setup. Your car needs a new rhomulan bypass chord. That's what you have going on
[/quote]
I'll make sure to replace that about the same time I sort out all the leaks in my fallopian tubes.
Cole
This is from personal experience....
Check your firing order. If you swap 3 and 4 on the distributor, it will run, but neither 3 nor 4 will make power. They will just sit there, fat, dumb and happy.
This can happen if you mentally reverse the distributor rotation, and setup the plug wires that way.
Easy way to remember how to wire a 914 /4 engine....
Left side of the car.. cross the wires and hook them to the distributor towers on that side.
Right side of the car... hook them to the distributor towers directly.
Here's a crappy line drawing done with MSpaint to illustrate the point.
Clay P are you sure you are showing the wires correct??? . 1 4 3 2 clockwise. Is the firing order.
Sorry I took a look again you Got it 100% right.
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)