Printable Version of Topic

Click here to view this topic in its original format

914World.com _ 914World Garage _ Center tunnel fuel lines

Posted by: whitey May 7 2007, 12:05 PM

I'm going to replace my tunnel lines...can I get away with fabricating my own lines out of brake line (what size-2.0 FI) or should I buck up for the stainless lines?

Thanks

Posted by: skline May 7 2007, 12:08 PM

I have done a couple of my cars, not FI however but I used brake lines, they are stainless and they work great. I would think for FI you would use a 5/16 and 1/4? They only come in 5' lengths from Kragen which gets you from the front to the rear only. You would use rubber line from there. I bought a flaring tool and bender when I did my first carb conversion. Now all I do is V8 cars so I only need one line and block off the return line at the front.

Posted by: zymurgist May 7 2007, 12:20 PM

I used a pair of 5/16" mild steel brake lines from NAPA. (Those must be for trucks since I've never seen a car that used brake lines that big.) Got a 5' length for the tunnel and a shorter one for the engine compartment. Used a brass 90 degree fitting to make the turn. Used a Harbor Freight tubing bender to bend the heck out of the short lines so they come up in the stock location. It's a really nice custom job, if I do say so myself. wink.gif

If I had it to do over again, I would buy the stainless kit. No muss, no fuss, just install it and be done with it. But it wasn't available yet when I did the job.

This was for a 2.0 D-jet car and it seems to be getting enough fuel.

Posted by: 914Sixer May 7 2007, 02:21 PM

Buy the lines from Chris and be done with the replacement.

Posted by: SLITS May 7 2007, 03:28 PM

3/8" and 5/16" Stainless Tube (I bought 10' lengths)

or better yet

buy them from Racer Chris.

Posted by: rhodyguy May 7 2007, 10:18 PM

agree.gif no hassle deal with the ones chris offers. i know i would go thru atleast 2 10' pieces if i tried to make them. i'd have to buy the tubing bender set. tinkering is not my thing. even taking the end off of a coil wire and replacing it is pushing the limits. biggrin.gif

k

Posted by: PRS914-6 May 7 2007, 10:53 PM

If you are not going to race it, why not just use a good quality fuel injection hose the entire length? I don't know why everyone goes to the hassle of metal lines and all the fittings since the newer style hose is very good and designed for high pressure. Racing does prohibit this though. The rubber lines only take a couple of minutes to run.

I ran mine from the front fuel pump directly to the rear filter without any additional fittings. I slid some heat shrink over the portion inside the car for abrasion resistance and some temp insulating sleeve over the outside portion.
Attached Image
Attached Image

Posted by: John May 7 2007, 11:23 PM

QUOTE(PRS914-6 @ May 7 2007, 08:53 PM) *

If you are not going to race it, why not just use a good quality fuel injection hose the entire length? I don't know why everyone goes to the hassle of metal lines and all the fittings since the newer style hose is very good and designed for high pressure. Racing does prohibit this though. The rubber lines only take a couple of minutes to run.

I ran mine from the front fuel pump directly to the rear filter without any additional fittings. I slid some heat shrink over the portion inside the car for abrasion resistance and some temp insulating sleeve over the outside portion.
Attached Image
Attached Image



Wow, you have the car up on a single scary style jackstand. I'm not getting under there.
poke.gif

Posted by: skline May 7 2007, 11:30 PM

He was just demonstrating the amazing balance his car has!! I wouldnt get under there either. huh.gif

Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)