Posted by: SirAndy Apr 29 2009, 12:36 PM
I have what appears to be a factory /6 oil feedline from the tank to the motor. It's a large black hose with aluminum fittings on each end.
Does anyone know the size and thread pitch of the end that goes to the motor?
I'm trying to find a short adapter to 12AN as i need to run some additional hose and my motor inlet has a 12AN fitting as well.
Andy
Posted by: PRS914-6 Apr 29 2009, 12:41 PM
QUOTE(SirAndy @ Apr 29 2009, 11:36 AM)
I have what appears to be a factory /6 oil feedline from the tank to the motor. It's a large black hose with aluminum fittings on each end.
Does anyone know the size and thread pitch of the end that goes to the motor?
I'm trying to find a short adapter to 12AN as i need to run some additional hose and my motor inlet has a 12AN fitting as well.
Andy
Andy, Patrick Motorsports has a metric to AN adapter for that. I think B.A.T in Florida has them as well. Both ends....
Posted by: SirAndy Apr 29 2009, 12:47 PM
Looks like this is it. 30mm to 12AN ...
http://www.patrickmotorsports.com/part/560/
Andy
Attached image(s)
Posted by: rudedude Apr 29 2009, 12:47 PM
Which one?
To the steel line at front or below the cooler?
I can go measure mine in a few minutes.
Posted by: sixnotfour Apr 29 2009, 12:50 PM
smart racing has em too;
http://www.smartracingproducts.com/engine.htm
Posted by: SirAndy Apr 29 2009, 12:51 PM
QUOTE(rudedude @ Apr 29 2009, 11:47 AM)
Which one?
To the steel line at front or below the cooler?
I can go measure mine in a few minutes.
Well, my setup is a bit different.
From the tank to the line next to where you have your oil cooler. On the drivers side.
Andy
Posted by: SirAndy Apr 29 2009, 01:21 PM
QUOTE(rudedude @ Apr 29 2009, 12:09 PM)
Mine is 30mm x 1.5mm
Thank you sir!
Andy
Posted by: 9146986 Apr 29 2009, 08:23 PM
You might also try Pegasus Racing.
Posted by: jt914-6 Apr 29 2009, 08:54 PM
Andy, does your cooler look like this? You can see on it the adaptor I got from Pegasus. 30mm x 1.5mm female to 12an male. PN# 1219-12an. $38.99 in my last catalog.....
Posted by: SirAndy Apr 29 2009, 09:29 PM
QUOTE(jt914-6 @ Apr 29 2009, 07:54 PM)
Andy, does your cooler look like this?
Nope. The 3.6L does not have a engine mounted cooler.
Andy
Posted by: jt914-6 Apr 29 2009, 10:03 PM
Like the one PRS914-6 posted? That would be a male 30 x 1.5mm to 12an. Pegasus's PN is 1218-12an. $28.99. Sorry, didn't know what engine you had...
Posted by: SirAndy Apr 29 2009, 10:08 PM
QUOTE(jt914-6 @ Apr 29 2009, 09:03 PM)
Like the one PRS914-6 posted? That would be a male 30 x 1.5mm to 12an. Pegasus's PN is 1218-12an. $28.99. Sorry, didn't know what engine you had...
Yes, sort of like in his pic, but i have a hard line on the engine that goes towards the front firewall and ends in a 12AN fitting.
The hose from the Oiltank has a metric fitting.
I'd like to get a short line (12AN) with a "T" for easy oilchange inbetween the two, hence my question about a adapter for the oil line end.
It seems that either a 30mm to 12AN male or female will do as the "T" is available with both types of ends.
Andy