Same old story. Boy falls for project with "potential"....finally has to admit he will never have time to complete it.
Orphan project looking for good home. Truly great platform for dream project. NO surprises!
1973 SBC V8 Conversion. Everything done to date was with the intention of keeping the vehicle forever. i.e. front wheel wells have individual vent holes drilled and champhered rather than the standard chop job.
Lots of cool stuff:
As close to NO RUST as you will find in a 914. ZERO RUST in longs or hell hole.
Sheridan racing body kit
SBC 350 engine with AFR 180 heads.
Renegade conversion parts.
new 750 cfm spread bore carb
new headers
901 transaxel with 1st gear blocked off
new rennshifter
new tangering racing shift bushings, shift bar, linkage, and precision shift adjuster and clutch pulley adapter shifts better than any 914 I have driven.
new corbeau racing seats
NO rips or cracks in dash
Autopower rollbar with crossbracing
Ron Davis aluminum radiator
boxed rear trailing arms
reinforced chassis
Aluminum American racing wheels (look like wide fuchs)
6 point simpson harnesses
New closed cell optima battery
911 5 lug hubs
911 front suspension
new elephant racing rear bronze bushings
weltmeister front swaybar
bilsteins all four corners
911 "S" front calipers
911 rear calipers including working parking brake set up
New 23mm mastercylinder
Quick release 3 spoke racing wheel
GT engine lid
Powdercoated fuel tank
SS fuel and brake lines
new mallory cap, wires, and plugs
I have +/- $10K invested to date.
List needed to complete.
1) replace engine gaskets
2) replace caliper o-ring (only other side was leaking initially and I foolishly only replaced that o-ring)
3) tires and alignment
4) paint
5) rubber
Current tags and registration. Car is VERY fast and runs and shifts well but will need to be towed due to old tires, engine oil leak (Local mechanic recommends removing engine and replacing all gaskets) and front caliper leak (have new s-caliper o-ring).
Located in Calistoga California 94515
First person to show up with $6000 and a trailer can take her home.
Delete
Duh...
Car is located in Calistoga California 94515
That is a killer deal for sure! I hope someone local buys that car and finishes it. That car would be a gas to drive. GLWTS!
I have been getting inquiries about what is required to complete this project.
Here is an overview:
Electrical
1) attach ground
2) run + to starter
3) complete attachments to fuel pump etc.
***note...car has renegade wiring harness installed and VDO sending units for coolant temp and oil pressure.
Fuel
1) install gas tank (fresh powdercoated OEM tank included)
2) install fuel pump (high flow holley included)
3) attach 1 and 2 to tangerine racing SS hard line (installed)
4) add fuel!
Mechanical
1) attach shift linkage from firewall to transaxel (included with boots/bushings)
2) install axels (included)
3) purchase/install shift knob
Exhaust
1) purchase/install from headers to tailpipe
Brakes
1) install master cylinder (new 23mm included)
2) install SS lines (included)
3) bleed
Fire her up!!!!!
Could this be used for aggressive street use? In other words, street legal with conventional clear title? Just curious!
.....and if you could email more pics that would be great.
blaine.sellie@comcast.net
interior images
console.pdf ( 1.04mb )
Number of downloads: 223
dash_2.pdf ( 807.88k )
Number of downloads: 165
dash.pdf ( 720.1k )
Number of downloads: 139
interior.pdf ( 711.76k )
Number of downloads: 205
seats.pdf ( 767.92k )
Number of downloads: 193
engine images
engine_left.pdf ( 749.66k )
Number of downloads: 167
engine_right.pdf ( 804.36k )
Number of downloads: 145
hellhole.pdf ( 872.29k )
Number of downloads: 197
gas_tank.pdf ( 830.4k )
Number of downloads: 149
exterior images
front.pdf ( 443.95k )
Number of downloads: 186
side_rear.pdf ( 584.99k )
Number of downloads: 169
side.pdf ( 664.04k )
Number of downloads: 142
wheel.pdf ( 626.42k )
Number of downloads: 147
radiator images
front_wheelwell.pdf ( 652.95k )
Number of downloads: 169
radiator.pdf ( 587.84k )
Number of downloads: 176
ron_davis_radiator.pdf ( 601.23k )
Number of downloads: 168
steering_wheel.pdf ( 851.12k )
Number of downloads: 147
Those American 200S's have been my absolute favorite wheel since I first saw them in the 60s. Congrats on finding a set and they look killer!
Fig
Going
I like it!! First time I've seen American five spokes on a Porsche,looks cool!
T
Listing on eBay next week
You know you want it!
I am interested. I don't see a way to PM you or your contact info. Could you please email me with your contact info to discuss?
Thanks,
Bryan
x98boardwell@yahoo.com
Just sold my -4, plan on heading your way on SAT to check her out - will give you a ring!
td
Wow. Why is this thing not sold yet, for $5k?
NLA
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)