 950 CC Type 4, 2 cylinder "big bore" |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Al Meredith |
 Jan 29 2015, 04:32 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 960 Joined: 4-November 04 From: Atlanta, ga Member No.: 3,061  |
I've wanted to do this for years! I just finished a 2 cylinder Ty 4 engine. I had a case that was not in real good shape and a couple of 1.7 heaqds that were OK. I welded up the oil holes on #2 & 4 and welded up 4 cam folowers , had the 1.7 heads fly cut for a big bore (96MM) P & C and have 1/2 of a 1911. For now and for simplicity I installed a standard 32/36 setup. I installed it om my engine start up stand and it started right up and ran fine , 60 PSI oil pressure at idle. No need to send a picture because it looks just like a regular engine although it sounds like a motorcycle.
I have a question for the forum, any suggestions on a carb set up?? I have a couple of old 1.7 bus carbs with the manifolds , I can use one of these carbs and center mount it . I can just continue to use the 32 MM weber and block off the 36 MM side??? any help. AL |
   |
 
|
Posts in this topic
Al Meredith 950 CC Type 4 Jan 29 2015, 04:32 PM
76-914 You might get some info from Leonard Millholand, i... Jan 29 2015, 04:48 PM Mueller Neat, however you need to take it to the next leve... Jan 29 2015, 05:16 PM
SirAndy Neat, however you need to take it to the next leve... Jan 29 2015, 06:37 PM
stugray
Neat, however you need to take it to the next lev... Jan 30 2015, 01:08 PM Elliot Cannon Do you have pictures, or are you just making shit ... Jan 29 2015, 08:06 PM siverson > No need to send a picture
WHAT?!?!?... Jan 29 2015, 08:08 PM poorsche914 > No need to send a picture
Perhaps not a pic... Jan 29 2015, 08:19 PM siverson :ttiwwp: Jan 29 2015, 08:09 PM Mark Henry I take it that this is for a kit plane?
Wouldn... Jan 30 2015, 07:59 AM Mueller I guess you could also convert it into a portable ... Jan 30 2015, 09:36 AM Mark Henry
I guess you could also convert it into a portable... Jan 30 2015, 10:45 AM MJHanna On the one I built I just cut a Weber in 2 and use... Jan 30 2015, 09:41 AM Al Meredith My initial plan was to use this as an emergancy po... Jan 30 2015, 11:44 AM Al Meredith I was at Chuck Becks (beck speedster and beck 550)... Jan 30 2015, 02:40 PM Dave_Darling Al, that was probably a "Polo motor". G... Jan 30 2015, 04:32 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th May 2024 - 09:00 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.